12/30241229 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
BS 7910 - GUIDE TO METHODS FOR ASSESSING THE ACCEPTABILITY OF FLAWS IN METALLIC STRUCTURES
Hardcopy , PDF
English
31-12-2013
Foreword
0 Introduction
1 Scope
2 Normative references
3 Symbols and definitions
4 Types of flaw
5 Modes of failure and material damage mechanisms
6 Information required for assessment
7 Assessment for fracture resistance
8 Assessment for fatigue
9 Assessment of flaws under creep and creep/fatigue
conditions
10 Assessment for other modes of failure
Annex A (normative) - Evaluation under mode I, II and
III loads
Annex B (informative) - Assessment procedures for
tubular joints in offshore structures
Annex C (informative) - Fracture assessment procedures
for pressure vessels and pipelines
Annex D (normative) - Stress due to misalignment
Annex E - Flaw recharacterization
Annex F (normative) - Procedures for
Leak-before-Break assessment
Annex G (normative) - The assessment of locally
thinned areas (LTAs)
Annex H (normative) - Reporting of fracture, fatigue
or creep assessments
Annex I (informative) - The significance of strength
mismatch on the fracture behaviour of
welded joints
Annex J (informative) - Use of Charpy V-notch impact
tests to estimate fracture toughness
Annex K (informative) - Probabilistic assessment
Annex L (informative) - Fracture toughness determination
for welds
Annex M (normative) - Stress intensity factor solutions
Annex N (informative) - Allowance for constraint effects
Annex O (informative) - Consideration of proof testing
and warm prestressing
Annex P (normative) - Compendium of reference stress
and limit load solutions for homogeneous and
strength mismatched structures
Annex Q (informative) - Residual stress distributions
in as-welded joints
Annex R (normative) - Determination of plasticity
interaction effects with combined primary
and secondary loading
Annex S (informative) - Information for making high
temperature crack growth assessments
Annex T (informative) - Guidance on the use of NDT with ECA
Annex U (informative) - Worked examples in fatigue
assessment using the quality category approach
Bibliography
BS 7910.
| Committee |
WEE/37
|
| DocumentType |
Draft
|
| Pages |
522
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| BS 7608:1993 | Code of practice for fatigue design and assessment of steel structures |
| BS EN ISO 17640:2010 | Non-destructive testing of welds. Ultrasonic testing. Techniques, testing levels, and assessment |
| ASTM E 1457 : 2015 : REDLINE | Standard Test Method for Measurement of Creep Crack Growth Times in Metals |
| BS EN 10025-3:2004 | Hot rolled products of structural steels Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| BS EN ISO 12737:2010 | Metallic materials. Determination of plane-strain fracture toughness |
| BS EN 10025-2:2004 | Hot rolled products of structural steels Technical delivery conditions for non-alloy structural steels |
| BS EN ISO 6892-2:2011 | Metallic materials. Tensile testing Method of test at elevated temperature |
| BS EN ISO 15653:2010 | Metallic materials. Method of test for the determination of quasistatic fracture toughness of welds |
| BS EN 1435:1997 | Non-destructive examination of welds. Radiographic examination of welded joints |
| BS EN 10225:2009 | Weldable structural steels for fixed offshore structures. Technical delivery conditions |
| BS ISO 12108:2012 | Metallic materials. Fatigue testing. Fatigue crack growth method |
| BS EN 1993-1-1 : 2005 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - PART 1-1: GENERAL RULES AND RULES FOR BUILDINGS |
| BS EN ISO 6520-1:2007 | Welding and allied processes. Classification of geometric imperfections in metallic materials Fusion welding |
| BS EN ISO 23279:2017 | Non-destructive testing of welds. Ultrasonic testing. Characterization of discontinuities in welds |
| BS EN ISO 6892-1:2016 | Metallic materials. Tensile testing Method of test at room temperature |
| BS EN ISO 11782-2:2008 | Corrosion of metals and alloys. Corrosion fatigue testing Crack propagation testing using precracked specimens |
| ASTM E 2760 : 2016 : REDLINE | Standard Test Method for Creep-Fatigue Crack Growth Testing |
| BS EN ISO 17638:2016 | Non-destructive testing of welds. Magnetic particle testing |
| BS EN 571-1:1997 | Non-destructive testing. Penetrant testing General principles |
| API 579-1 : 2016 | FITNESS-FOR-SERVICE |
| PD 6525-1:1990 | Elevated temperature properties for steels for pressure purposes. Stress rupture properties |
| BS EN 1993-1-2:2005 | Eurocode 3. Design of steel structures General rules - Structural fire design |
| BS EN ISO 7539-1:2012 | Corrosion of metals and alloys. Stress corrosion testing General guidance on testing procedures |
| BS EN 462-3:1997 | Non-destructive testing. Image quality of radiographs Image quality classes for ferrous metals |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.