12/30250149 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 16143-2 - STAINLESS STEELS FOR GENERAL PURPOSES - PART 2: SEMI-FINISHED PRODUCTS, BARS, RODS AND SECTIONS
Hardcopy , PDF
English
31-05-2014
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Information to be supplied by the purchaser
6 Classification of grades
7 Requirements
8 Inspection, testing and conformance of products
9 Marking
Annex A (informative) - Guidelines for further treatment
(including heat treatment) in fabrication
Annex B (informative) - Designations of the steels given
in Table 2 and of comparable grades covered in ASTM-,
EN-, JIS- and GB-Standards
Annex C (informative) - Applicable dimensional standards
Bibliography
BS ISO 16143-2
| Committee |
ISE/105
|
| DocumentType |
Draft
|
| Pages |
42
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 404:2013 | Steel and steel products — General technical delivery requirements |
| ISO 6929:2013 | Steel products — Vocabulary |
| ISO 6506-1:2014 | Metallic materials — Brinell hardness test — Part 1: Test method |
| ISO/TS 4949:2016 | Steel names based on letter symbols |
| ISO/TR 9769:1991 | Steel and iron — Review of available methods of analysis |
| ISO 15510:2014 | Stainless steels — Chemical composition |
| EN 10056-2:1993 | Structural steel equal and unequal leg angles - Part 2: Tolerances on shape and dimensions |
| ISO 16124:2015 | Steel wire rod — Dimensions and tolerances |
| EN 10279:2000 | Hot rolled steel channels - Tolerances on shape, dimensions and mass |
| ISO 1035-3:1980 | Hot-rolled steel bars — Part 3: Dimensions of flat bars |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| EN 10034:1993 | Structural steel I and H sections - Tolerances on shape and dimensions |
| ISO 1035-4:1982 | Hot-rolled steel bars — Part 4: Tolerances |
| EN 10024:1995 | Hot rolled taper flange I sections - Tolerances on shape and dimensions |
| ISO 148-1:2016 | Metallic materials — Charpy pendulum impact test — Part 1: Test method |
| EN 10060:2003 | Hot rolled round steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ISO 1035-1:1980 | Hot-rolled steel bars — Part 1: Dimensions of round bars |
| EN 10017:2004 | Steel rod for drawing and/or cold rolling - Dimensions and tolerances |
| ISO 4955:2016 | Heat-resistant steels |
| ISO 3651-2:1998 | Determination of resistance to intergranular corrosion of stainless steels — Part 2: Ferritic,austenitic and ferritic-austenitic (duplex) stainless steels — Corrosion test in media containing sulfuric acid |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| ISO 10474:2013 | Steel and steel products — Inspection documents |
| ISO 1035-2:1980 | Hot-rolled steel bars — Part 2: Dimensions of square bars |
| ISO 6892-2:2011 | Metallic materials — Tensile testing — Part 2: Method of test at elevated temperature |
| EN 10061:2003 | Hot rolled hexagon steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| EN 10059:2003 | Hot rolled square steel bars for general purposes - Dimensions and tolerances on shape and dimensions |
| ASTM A 555/A555M : 2016 : REDLINE | Standard Specification for General Requirements for Stainless Steel Wire and Wire Rods |
| EN 10055:1995 | Hot rolled steel equal flange tees with radiused root and toes - Dimensions and tolerances on shape and dimensions |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
| ISO 14284:1996 | Steel and iron — Sampling and preparation of samples for the determination of chemical composition |
| ISO 6931-1:2016 | Stainless steels for springs — Part 1: Wire |
| ISO 4954:1993 | Steels for cold heading and cold extruding |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.