12/30256736 DC : 0
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 4437-1 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 1: GENERAL
Available format(s)
Hardcopy , PDF
Language(s)
English
Publisher
Superseded date
31-01-2014
Superseded by
£20.00
Excluding VAT
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and
abbreviations
4 Material
Bibliography
BS ISO 4437-1.
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
22
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 13953:2001 | Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 1133-1:2011 | Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method |
| ISO 6964:1986 | Polyolefin pipes and fittings — Determination of carbon black content by calcination and pyrolysis — Test method and basic specification |
| ISO 13477:2008 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test) |
| ISO 3:1973 | Preferred numbers — Series of preferred numbers |
| ISO 18553:2002 | Method for the assessment of the degree of pigment or carbon black dispersion in polyolefin pipes, fittings and compounds |
| ISO/TS 10839:2000 | Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation |
| ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes |
| ISO 11414:2009 | Plastics pipes and fittings — Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion |
| ISO 12162:2009 | Thermoplastics materials for pipes and fittings for pressure applications — Classification, designation and design coefficient |
| ISO 6259-1:2015 | Thermoplastics pipes — Determination of tensile properties — Part 1: General test method |
| ISO 13478:2007 | Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST) |
| ISO 16871:2003 | Plastics piping and ducting systems — Plastics pipes and fittings — Method for exposure to direct (natural) weathering |
| ISO 472:2013 | Plastics — Vocabulary |
| ISO 13954:1997 | Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm |
| ISO 1183-1:2012 | Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pyknometer method and titration method |
| ISO 1183-2:2004 | Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density gradient column method |
| ISO 15512:2016 | Plastics — Determination of water content |
| ISO 11357-6:2008 | Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
| ISO 4065:1996 | Thermoplastics pipes — Universal wall thickness table |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| CEN/TS 1555-7:2013 | Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity |
| ISO 6259-3:2015 | Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes |
| ISO 760:1978 | Determination of water — Karl Fischer method (General method) |
| ISO 11413:2008 | Plastics pipes and fittings — Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting |
| ISO 1043-1:2011 | Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics |
| EN 12099:1997 | Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
Summarise
£20.00
Excluding VAT
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.