12/30258383 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN ISO 11297-3 - PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND DRAINAGE AND SEWERAGE NETWORKS UNDER PRESSURE - PART 3: LINING WITH CLOSE-FIT PIPES
Hardcopy , PDF
English
31-07-2013
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Pipes at the "M" stage
6 Fittings at the "M" stage
7 Ancillary components
8 Fitness for purpose of the installed lining system
at the "I" stage
9 Installation practice
Annex A (normative) - Factory-folded heat-reverted
polyethylene (PE) pipe - Determination of
memory ability
Bibliography
BS EN ISO 11297-3
| Committee |
PRI/88/3
|
| DocumentType |
Draft
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN ISO 11297-3 : DRAFT 2012 | Identical |
| EN 12201-4:2012 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 4: Valves |
| ISO 4427-3:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3: Fittings |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 8772:2006 | Plastics piping systems for non-pressure underground drainage and sewerage — Polyethylene (PE) |
| ISO 4427-1:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 1: General |
| ISO 11295:2017 | Classification and information on design and applications of plastics piping systems used for renovation and replacement |
| ISO 12176-1:2017 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1: Butt fusion |
| ISO 3:1973 | Preferred numbers — Series of preferred numbers |
| ISO 4427-5:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5: Fitness for purpose of the system |
| ISO 12176-2:2008 | Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2: Electrofusion |
| ISO 6259-1:2015 | Thermoplastics pipes — Determination of tensile properties — Part 1: General test method |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| EN 12201-2:2011+A1:2013 | Plastics piping systems for water supply, and for drainage and sewerage under pressure - Polyethylene (PE) - Part 2: Pipes |
| ISO 497:1973 | Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers |
| ISO 9967:2016 | Thermoplastics pipes — Determination of creep ratio |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
| ISO 4427-2:2007 | Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 2: Pipes |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.