12/30258651 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 492 - ROLLING BEARINGS - RADIAL BEARINGS - DIMENSIONAL AND GEOMETRICAL TOLERANCES
Hardcopy , PDF
English
31-07-2014
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Limit deviations and tolerance values
Annex A (Informative) - Symbols and descriptions
of traditional terms in relationship with
new terms
Annex B (Informative) - Example of drawing
indications of characteristics with
specification for rolling bearings
Annex C (informative) - Illustration of ISO 1132-1
and ISO 14405-1 definitions
Annex D (informative) - Description with illustrations
for specification modifiers of linear sizes
Annex E (informative) - Indication and calculation of
taper tolerances in specific cross sections
Annex F (informative) - Relation to the GPS matrix
model
Bibliography
BS ISO 492
| Committee |
MCE/7
|
| DocumentType |
Draft
|
| Pages |
71
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 8443:2010 | Rolling bearings — Radial ball bearings with flanged outer ring — Flange dimensions |
| ISO 8015:2011 | Geometrical product specifications (GPS) — Fundamentals — Concepts, principles and rules |
| ISO 1132-2:2001 | Rolling bearings — Tolerances — Part 2: Measuring and gauging principles and methods |
| ISO/TS 17863:2013 | Geometrical product specification (GPS) — Tolerancing of moveable assemblies |
| ISO 1119:2011 | Geometrical product specifications (GPS) — Series of conical tapers and taper angles |
| ISO 1101:2017 | Geometrical product specifications (GPS) — Geometrical tolerancing — Tolerances of form, orientation, location and run-out |
| ISO 5593:1997 | Rolling bearings — Vocabulary |
| ISO 14253-1:2017 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 1: Decision rules for verifying conformity or nonconformity with specifications |
| ISO 355:2007 | Rolling bearings — Tapered roller bearings — Boundary dimensions and series designations |
| ISO 14405-2:2011 | Geometrical product specifications (GPS) — Dimensional tolerancing — Part 2: Dimensions other than linear sizes |
| ISO 582:1995 | Rolling bearings — Chamfer dimensions — Maximum values |
| ISO 1132-1:2000 | Rolling bearings — Tolerances — Part 1: Terms and definitions |
| ISO 286-1:2010 | Geometrical product specifications (GPS) — ISO code system for tolerances on linear sizes — Part 1: Basis of tolerances, deviations and fits |
| ISO 14660-2:1999 | Geometrical Product Specifications (GPS) — Geometrical features — Part 2: Extracted median line of a cylinder and a cone, extracted median surface, local size of an extracted feature |
| ISO 15241:2012 | Rolling bearings — Symbols for physical quantities |
| ISO 14660-1:1999 | Geometrical Product Specifications (GPS) — Geometrical features — Part 1: General terms and definitions |
| ISO 14405-1:2016 | Geometrical product specifications (GPS) — Dimensional tolerancing — Part 1: Linear sizes |
| ISO 14253-2:2011 | Geometrical product specifications (GPS) — Inspection by measurement of workpieces and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in calibration of measuring equipment and in product verification |
| ISO/R 1938:1971 | ISO system of limits and fits — Part II : Inspection of plain workpieces |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.