13/30199128 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
BS 6891 - SPECIFICATION FOR THE INSTALLATION AND MAINTENANCE OF LOW PRESSURE GAS INSTALLATION PIPEWORK OF UP TO 35 MM (R1[1/4]) IN PREMISES
Hardcopy , PDF
English
30-11-2015
1 Scope
2 Normative references
3 Terms and definitions
4 Competence
5 Design and planning
6 Materials
7 Jointing
8 Installation
9 Prevention of corrosion and degradation
10 Commissioning
11 Maintenance
Annexes
Annex A (informative) - Guide for sizing gas supplies:
Natural gas installations
Annex B (informative) - Sulfidation of natural gas
installations
Annex C (informative) - Summary and principal conclusions
of the Advantica Research Project, 'Gas in
intermediate floors, Report Number 6699
Annex D (informative) - Protected area
Annex E (normative) - LPG Final stage regulator and
safety devices
Bibliography
BS 6891.
| Committee |
GSE/30
|
| DocumentType |
Draft
|
| Pages |
79
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| BS EN 10312:2002 | Welded stainless steel tubes for the conveyance of aqueous liquids inclu ding water for human consumption. Technical delivery conditions |
| BS EN 1949 : 2011 | SPECIFICATION FOR THE INSTALLATION OF LPG SYSTEMS FOR HABITATION PURPOSES IN LEISURE ACCOMMODATION VEHICLES AND ACCOMMODATION PURPOSES IN OTHER VEHICLES |
| BS EN ISO 10239:2017 | Small craft. Liquefied petroleum gas (LPG) systems |
| BS EN 751-2:1997 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Non-hardening jointing compounds |
| BS EN 1555-3 : 2010 | PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 3: FITTINGS |
| BS EN 15266:2007 | Stainless steel pliable corrugated tubing kits in buildings for gas with an operating pressure up to 0,5 bar |
| BS 1494:1951 | Specification. Fixing accessories for building purposes |
| BS EN 1555-2:2010 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) Pipes |
| BS EN 10217-2 : 2002 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 2: ELECTRIC WELDED NON-ALLOY AND ALLOY STEEL TUBES WITH SPECIFIED ELEVATED TEMPERATURE PROPERTIES |
| BS EN 13786 : 2004 | AUTOMATIC CHANGE-OVER VALVES HAVING A MAXIMUM OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| BS EN ISO 228-2:2003 | Pipe threads where pressure-tight joints are not made on the threads Verification by means of limit gauges |
| BS EN 14800:2007 | Corrugated safety metal hose assemblies for the connection of domestic appliances using gaseous fuels |
| BS EN 10217-7:2014 | Welded steel tubes for pressure purposes. Technical delivery conditions Stainless steel tubes |
| BS EN 10216-5:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Stainless steel tubes |
| PD 5482-3:2005 | Code of practice for domestic butane and propane gas-burning installations Installations in boats, yachts and other vessels |
| BS EN 1057 : 2006 | COPPER AND COPPER ALLOYS - SEAMLESS, ROUND COPPER TUBES FOR WATER AND GAS IN SANITARY AND HEATING APPLICATIONS |
| BS EN 1044:1999 | Brazing. Filler metals |
| BS EN 14324:2004 | Brazing. Guidance on the application of brazed joints |
| BS EN 60079-10:2003 | Electrical apparatus for explosive gas atmospheres Classification of hazardous areas |
| BS EN 29453:1994 | Soft solder alloys. Chemical compositions and forms |
| BS 5482-2:1977 | Domestic butane- and propane-gas-burning installations Installations in caravans and non-permanent dwellings |
| BS EN 751-3:1997 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Unsintered PTFE tapes |
| BS EN 1254-2:1998 | Copper and copper alloys. Plumbing fittings Fittings with compression ends for use with copper tubes |
| BS 7838:1996 | Specification for corrugated stainless steel semi-rigid pipe and associated fittings for low-pressure gas pipework of up to DN 50 |
| BS EN 1775:2007 | Gas supply. Gas pipework for buildings. Maximum operating pressure less than or equal to 5 bar. Functional recommendations |
| BS EN 751-1:1997 | Sealing materials for metallic threaded joints in contact with 1st, 2nd and 3rd family gases and hot water Anaerobic jointing compounds |
| BS EN 13785 : 2005 | REGULATORS WITH A CAPACITY OF UP TO AND INCLUDING 100 KG/H, HAVING A MAXIMUM NOMINAL OUTLET PRESSURE OF UP TO AND INCLUDING 4 BAR, OTHER THAN THOSE COVERED BY EN 12864 AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| BS EN 1254-5:1998 | Copper and copper alloys. Plumbing fittings Fittings with short ends for capillary brazing to copper tubes |
| BS EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads Taper external threads and parallel internal threads. Dimensions, tolerances and designation |
| BS EN 10216-1:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Non-alloy steel tubes with specified room temperature properties |
| BS 5114:1975 | Specification for performance requirements for joints and compression fittings for use with polyethylene pipes |
| BS EN 10217-1:2002 | Welded steel tubes for pressure purposes. Technical delivery conditions Non-alloy steel tubes with specified room temperature properties |
| BS EN 1254-4:1998 | Copper and copper alloys. Plumbing fittings Fittings combining other end connections with capillary or compression ends |
| BS EN 10216-2:2013 | Seamless steel tubes for pressure purposes. Technical delivery conditions Non-alloy and alloy steel tubes with specified elevated temperature properties |
| BS EN 12864 : 2001 | LOW-PRESSURE, NON ADJUSTABLE REGULATORS HAVING A MAXIMUM OUTLET PRESSURE OF LESS THAN OR EQUAL TO 200 MBAR, WITH A CAPACITY OF LESS THAN OR EQUAL TO 4 KG/H, AND THEIR ASSOCIATED SAFETY DEVICES FOR BUTANE, PROPANE OR THEIR MIXTURES |
| BS EN 10255:2004 | Non-alloy steel tubes suitable for welding and threading. Technical delivery conditions |
| BS EN 1555-1:2010 | Plastics piping systems for the supply of gaseous fuels. Polyethylene (PE) General |
| BS EN ISO 228-1:2003 | Pipe threads where pressure-tight joints are not made on the threads Dimensions, tolerances and designation |
| BS EN 331:2015 | Manually operated ball valves and closed bottom taper plug valves for gas installations for buildings |
| BS EN 1254-1:1998 | Copper and copper alloys. Plumbing fittings Fittings with ends for capillary soldering or capillary brazing to copper tubes |
| BS EN 10242:1995 | Threaded pipe fittings in malleable cast iron |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.