13/30285283 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 13001-3-5 - CRANES - GENERAL DESIGN - PART 3-5: LIMIT STATE AND PROOF OF COMPETENCE OF FORGED HOOKS
Hardcopy , PDF
English
31-01-2017
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions, symbols and abbreviations
4 General requirements
5 Static strength
6 Fatigue strength
7 Verification of conformity with the requirements
8 Information for use
Annex A (informative) - Sets of single hooks
Annex B (informative) - A series of ramshorn hooks of type
RS/RSN and RF/RFN, dimensions of forgings
Annex C (normative) - Static limit design forces of hook
bodies
Annex D (normative) - Fatigue limit design forces of hook
bodies
Annex E (normative) - Hook body calculation and specific
spectrum ratio factors
Annex F (normative) - A selection of material qualities
for hooks of type RS and RF
Annex G (informative) - Sets of hook shank and thread
designs
Annex H (normative) - Bending of curved beams
Annex I (normative) - Calculation of hook suspension
tilting resistance, articulation by a hinge or a
rope reeving system
Annex J (informative) - Guidance for the selection of a
hook size using the Annexes C to E
Annex K (normative) - Information to be provided by the
hook manufacturer
Annex L (informative) - Selection of a suitable set of crane
standards for a given application
Annex ZA (informative) - Relationship between this European
Standard and the Essential Requirements of EU
Directive 2006/42/EC
Bibliography
BS EN 13001-3-5
| Committee |
MHE/3/1
|
| DocumentType |
Draft
|
| Pages |
83
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| PREN 13001-3-5 : DRAFT 2013 | Identical |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| ISO 4287:1997 | Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms, definitions and surface texture parameters |
| ISO 4306-1:2007 | Cranes — Vocabulary — Part 1: General |
| BS EN 1677-5 : 2001 | COMPONENTS FOR SLINGS - SAFETY - PART 5: FORGED STEEL LIFTING HOOKS WITH LATCH - GRADE 4 |
| EN 10254:1999 | Steel closed die forgings - General technical delivery conditions |
| EN 614-1:2006+A1:2009 | Safety of machinery - Ergonomic design principles - Part 1: Terminology and general principles |
| ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
| EN 10045-1 : 1990 | METALLIC MATERIALS - CHARPY IMPACT TEST - PART 1: TEST METHOD |
| EN 13001-2:2014 | Crane safety - General design - Part 2: Load actions |
| EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
| EN 13001-1:2015 | Cranes - General design - Part 1: General principles and requirements |
| EN 10250-2:1999 | Open die steel forgings for general engineering purposes - Part 2: Non-alloy quality and special steels |
| EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
| EN ISO 12100:2010 | Safety of machinery - General principles for design - Risk assessment and risk reduction (ISO 12100:2010) |
| DIN 15400:1990-06 | LIFTING HOOKS - MATERIALS, MECHANICAL PROPERTIES, LIFTING CAPACITY AND STRESSES |
| ISO 965-1:2013 | ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data |
| EN 10025-3:2004 | Hot rolled products of structural steels - Part 3: Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steels |
| CEN/TS 13001-3-2:2008 | Cranes - General design - Part 3-2: Limit states and proof of competence of wire ropes in reeving systems |
| EN 10250-3:1999 | Open die steel forgings for general engineering purposes - Part 3: Alloy special steels |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.