14/30310457 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN 60143-1 - SERIES CAPACITORS FOR POWER SYSTEMS - PART 1: GENERAL
Hardcopy , PDF
English
31-10-2015
FOREWORD
1 Scope and object
2 Normative references
3 Terms and definitions
4 Service conditions
5 Quality requirements and tests
6 Insulation level
7 Overloads, overvoltages and duty cycles
8 Safety requirements
9 Markings and instruction books
10 Guide for selection of ratings, installation and operation
Annex A (normative) - Test requirements and application guide
for external fuses and units to be externally fused
Annex B (informative) - Economic evaluation of series capacitor
bank losses
Annex C (informative) - Capacitor bank fusing and unit arrangement
Annex D (informative) - Examples of typical connection diagrams for
large series capacitor installations for transmission lines
Annex E (informative) - Precautions to be taken to avoid pollution of
the environment by polychlorinated biphenyls
Bibliography
BS EN 60143-1.
| Committee |
PEL/33
|
| DocumentType |
Draft
|
| Pages |
68
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| IEC 60060-2:2010 | High-voltage test techniques - Part 2: Measuring systems |
| IEC 60143-2:2012 | Series capacitors for power systems - Part 2: Protective equipment for series capacitor banks |
| IEC 60270:2000+AMD1:2015 CSV | High-voltage test techniques - Partial discharge measurements |
| IEC 61048:2006+AMD1:2015 CSV | Auxiliaries for lamps - Capacitors for use in tubular fluorescent and other discharge lamp circuits - General and safety requirements |
| IEC 60050-601:1985 | International Electrotechnical Vocabulary (IEV) - Part 601: Generation, transmission and distribution of electricity - General |
| IEC TS 60815-2:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 2: Ceramic and glass insulators for a.c. systems |
| IEC 60909-0:2016 | Short-circuit currents in three-phase a.c. systems - Part 0: Calculation of currents |
| IEC 60549:2013 | High-voltage fuses for the external protection of shunt capacitors |
| IEC TR 60996:1989 | Method for verifying accuracy of tan delta measurements applicable to capacitors |
| IEC 61049:1991 | Capacitors for use in tubular fluorescent and other discharge lamp circuits. Performance requirements |
| IEC 60721-2-6:1990 | Classification of environmental conditions. Part 2: Environmental conditions appearing in nature. Earthquake vibration and shock |
| IEC 60273:1990 | Characteristic of indoor and outdoor post insulators for systems with nominal voltages greater than 1000 V |
| IEC 62271-1:2017 | High-voltage switchgear and controlgear - Part 1: Common specifications for alternating current switchgear and controlgear |
| IEC 60252-1:2010+AMD1:2013 CSV | AC motor capacitors - Part 1: General - Performance, testing andrating - Safety requirements - Guidance for installation and operation |
| IEC 60071-2:1996 | Insulation co-ordination - Part 2: Application guide |
| IEC 60050-436:1990 | International Electrotechnical Vocabulary (IEV) - Part 436: Power capacitors |
| IEC 60060-1:2010 | High-voltage test techniques - Part 1: General definitions and test requirements |
| IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
| IEC 60143-3:2015 | Series capacitors for power systems - Part 3: Internal fuses |
| IEC TS 60871-2:2014 | Shunt capacitors for a.c. power systems having a rated voltage above 1 000 V - Part 2: Endurance testing |
| IEC TS 60815-1:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 1: Definitions, information and general principles |
| IEC 60143-4:2010 | Series capacitors for power systems - Part 4: Thyristor controlled series capacitors |
| IEEE 693-2005 | IEEE Recommended Practice for Seismic Design of Substations |
| IEC TS 60815-3:2008 | Selection and dimensioning of high-voltage insulators intended for use in polluted conditions - Part 3: Polymer insulators for a.c. systems |
| IEC 60110-1:1998 | Power capacitors for induction heating installations - Part 1: General |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.