15/30259978 DC : 0
NA
Status of Standard is Unknown
BS EN 62477-2 - SAFETY REQUIREMENTS FOR POWER ELECTRONIC CONVERTER SYSTEMS AND EQUIPMENT - PART 2: POWER ELECTRONIC CONVERTERS FROM 1000 V A.C. OR 1500 V D.C. UP TO 36 KV A.C. OR 54 KV D.C.
Hardcopy , PDF
English
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Terms and definitions
4 Protection against hazards
5 Test requirements
6 Information and marking requirements
7 Internal Arc Classification Requirements
Annex A (normative) - Additional information for protection
against electric shock
Annex B (informative) - Considerations for the reduction of
the pollution degree
Annex C (informative) - Symbols referred to in IEC 62477-1
Annex D (normative) - Evaluation of clearance and creepage
distances
Annex E (informative) - Altitude correction for clearances
Annex F (normative) - Clearance and creepage distance
determination for frequencies greater than 30 kHz
Annex G (informative) - Cross-sections of round conductors
Annex H (informative) - Guidelines for RCD compatibility
Annex I (informative) - Examples of overvoltage category
reduction
Annex J (informative) - Burn thresholds for touchable
surfaces
Annex K (informative) - Table of electrochemical potentials
Annex L (informative) - Measuring instrument for touch
current measurements
Annex M (informative) - Test probes for determining access
Annex N (normative) - Arc fault test and labelling
requirements
Bibliography
BS EN 62477-2.
| Committee |
PEL/22
|
| DocumentType |
Draft
|
| Pages |
86
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| IEC 60243-1:2013 | Electric strength of insulating materials - Test methods - Part 1: Tests at power frequencies |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 62423:2009 | Type F and type B residual current operated circuit-breakers with and without integral overcurrent protection for household and similar uses |
| IEC 61936-1:2010+AMD1:2014 CSV | Power installations exceeding 1 kV a.c. - Part 1: Common rules |
| IEC 60947-7-2:2009 | Low-voltage switchgear and controlgear - Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors |
| IEC 62271-200:2011 | High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
| IEC 62271-201:2014 | High-voltage switchgear and controlgear - Part 201: AC solid-insulation enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV |
| IEC 60073:2002 | Basic and safety principles for man-machine interface, marking and identification - Coding principles for indicators and actuators |
| IEC TS 61201:2007 | Use of conventional touch voltage limits - Application guide |
| IEC 61643-12:2008 | Low-voltage surge protective devices - Part 12: Surge protective devices connected to low-voltage power distribution systems - Selection and application principles |
| IEC 60364-5-53:2001+AMD1:2002+AMD2:2015 CSV | Electrical installations of buildings - Part 5-53: Selection and erection of electrical equipment - Isolation, switching and control |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| IEC 60947-7-1:2009 | Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors |
| IEC 61082-1:2014 RLV | Preparation of documents used in electrotechnology - Part 1: Rules |
| IEC 60085:2007 | Electrical insulation - Thermal evaluation and designation |
| IEEE 902-1998 | IEEE Guide for Maintenance, Operation, and Safety of Industrial and Commercial Power Systems (Yellow Book) (Color Book® Series) |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| NFPA 70E : 2018 | ELECTRICAL SAFETY IN THE WORKPLACE |
| IEC 62079:2001 | Preparation of instructions - Structuring, content and presentation |
| IEC 60664-5:2007 | Insulation coordination for equipment within low-voltage systems - Part 5: Comprehensive method for determining clearances and creepage distances equal to or less than 2 mm |
| IEC 60071-2:1996 | Insulation co-ordination - Part 2: Application guide |
| IEEE 1584-2002 | IEEE Guide for Performing Arc Flash Hazard Calculations |
| IEC 62477-1:2012+AMD1:2016 CSV | Safety requirements for power electronic converter systems and equipment - Part 1: General |
| IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
| IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
| IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
| IEC TR 60479-5:2007 | Effects of current on human beings and livestock - Part 5: Touch voltage threshold values for physiological effects |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.