15/30324138 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS EN ISO 15876-3 - PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - POLYBUTYLENE (PB) - PART 3: FITTINGS
Hardcopy , PDF
English
28-02-2017
1 Scope
2 Normative references
3 Terms and definitions, symbols
and abbreviated terms
4 Material characteristics
5 General characteristics
6 Geometrical characteristics
7 Mechanical characteristics of plastics fittings
8 Melt flow rate
9 Sealing elements
10 Performance requirements
11 Marking
Bibliography
BS EN ISO 15876-3.
| Committee |
PRI/88/2
|
| DocumentType |
Draft
|
| Pages |
22
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
| ISO 1167-2:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces |
| ISO 1133-1:2011 | Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method |
| ISO 1167-4:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Preparation of assemblies |
| ISO 9080:2012 | Plastics piping and ducting systems — Determination of the long-term hydrostatic strength of thermoplastics materials in pipe form by extrapolation |
| ISO/TS 15876-7:2003 | Plastics piping systems for hot and cold water installations — Polybutylene (PB) — Part 7: Guidance for the assessment of conformity |
| ISO 15876-1:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General |
| ISO 3126:2005 | Plastics piping systems — Plastics components — Determination of dimensions |
| ISO 1167-3:2007 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 3: Preparation of components |
| EN 1254-6:2012 | Copper and copper alloys - Plumbing fittings - Part 6: Fittings with push-fit ends |
| CEN/TR 12108:2012 | Plastics piping systems - Guidance for the installation inside buildings of pressure piping systems for hot and cold water intended for human consumption |
| ISO 15876-2:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes |
| EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
| ISO 15876-5:2017 | Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system |
| ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances and designation |
| ISO 7686:2005 | Plastics pipes and fittings — Determination of opacity |
| EN 10088-1:2014 | Stainless steels - Part 1: List of stainless steels |
| ISO 1167-1:2006 | Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.