16/30334068 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
BS ISO 8178-4 - RECIPROCATING INTERNAL COMBUSTION ENGINES - EXHAUST EMISSION MEASUREMENT - PART 4: STEADY-STATE TEST CYCLES FOR DIFFERENT ENGINE APPLICATIONS
Hardcopy , PDF
English
30-06-2017
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviated terms
5 Test conditions
6 Test fuels
7 Test cycles
8 Test run
9 Data evaluation and calculation
10 Engine control area
Annex A (normative) - Steady-state discrete-mode
test-cycles
Annex B (normative) - Steady-state ramped modal
test cycles (RMCs)
Annex C (normative) - Transient test cycles
Annex D (informative) - Calculation of the exhaust
gas mass flow and/or of the combustion air
mass flow
Annex E (informative) - Example programme for
calculation of exhaust mass flows
Annex F (informative) - Example of calculation
procedure (raw/partial flow)
Annex G (normative) - Installation requirements
for equipment and auxiliaries
Annex H (normative) - Molar based emission
calculations
Bibliography
BS ISO 8178-4.
| Committee |
MCE/14/-/3
|
| DocumentType |
Draft
|
| Pages |
246
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 3: Nozzles and Venturi nozzles |
| SAE J244_201106 | Measurement of Intake Air or Exhaust Gas Flow of Diesel Engines |
| ISO 8178-5:2015 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 5: Test fuels |
| CFR 40(PTS87-95) : JUL 2017 | PROTECTION OF ENVIRONMENT |
| ISO 7066-2:1988 | Assessment of uncertainty in the calibration and use of flow measurement devices — Part 2: Non-linear calibration relationships |
| ISO 5168:2005 | Measurement of fluid flow — Procedures for the evaluation of uncertainties |
| ISO 2710-1:2000 | Reciprocating internal combustion engines — Vocabulary — Part 1: Terms for engine design and operation |
| ISO 2710-2:1999 | Reciprocating internal combustion engines — Vocabulary — Part 2: Terms for engine maintenance |
| ISO 8178-1:2017 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 1: Test-bed measurement systems of gaseous and particulate emissions |
| ISO 8178-2:2008 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 2: Measurement of gaseous and particulate exhaust emissions under field conditions |
| ISO 8178-3:1994 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 3: Definitions and methods of measurement of exhaust gas smoke under steady-state conditions |
| ISO 5167-4:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 4: Venturi tubes |
| ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 2: Orifice plates |
| ISO/TR 3313:1998 | Measurement of fluid flow in closed conduits — Guidelines on the effects of flow pulsations on flow-measurement instruments |
| ISO 14396:2002 | Reciprocating internal combustion engines — Determination and method for the measurement of engine power — Additional requirements for exhaust emission tests in accordance with ISO 8178 |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 1: General principles and requirements |
| ISO 80000-1:2009 | Quantities and units — Part 1: General |
| ISO 8528-1:2005 | Reciprocating internal combustion engine driven alternating current generating sets — Part 1: Application, ratings and performance |
| ISO 8178-7:2015 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 7: Engine family determination |
| CFR 40(PTS1000-END) : JUL 2016 | PROTECTION OF ENVIRONMENT - ENVIRONMENTAL PROTECTION AGENCY AND DEPARTMENT OF JUSTICE COUNCIL ON ENVIRONMENTAL QUALITY |
| ISO 2534:1998 | Road vehicles — Engine test code — Gross power |
| ISO 9249:2007 | Earth-moving machinery — Engine test code — Net power |
| ISO 8665:2006 | Small craft — Marine propulsion reciprocating internal combustion engines — Power measurements and declarations |
| ISO 1585:1992 | Road vehicles — Engine test code — Net power |
| ISO 3046-3:2006 | Reciprocating internal combustion engines — Performance — Part 3: Test measurements |
| ISO 8178-6:2000 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 6: Report of measuring results and test |
| ISO 15550:2016 | Internal combustion engines — Determination and method for the measurement of engine power — General requirements |
| ISO 8178-8:2015 | Reciprocating internal combustion engines — Exhaust emission measurement — Part 8: Engine group determination |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.