17/30244737 DC : 0
NA
Status of Standard is Unknown
BS EN 17149 - RAILWAY APPLICATIONS - FATIGUE STRENGTH ASSESSMENT OF RAILWAY VEHICLE STRUCTURES BASED ON CUMULATIVE DAMAGE
Hardcopy , PDF
English
European foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions, symbols and abbreviations
4 Stress determination
5 Fatigue resistance
6 Concept of partial factors
7 Procedure of fatigue assessment
Annex A (informative) - Procedure for determination
of mean stress factors for non-welded
and welded structures
Annex B (informative) - Example specification for
permissible of volumetric defects in
castings of steel, iron and aluminium
Annex C (normative) - Surface roughness factor
for cut edges of steel
Annex D (normative) - Reference values of the fatigue
strength [Delta][sigma][c] and [Delta][tau][c] for
notch cases of welded structures of steel
Annex E (normative) - Reference values of the fatigue
strength [Delta][sigma][c] and [Delta][tau][c] for
notch cases of welded structures of aluminium
Annex F (normative) - Thickness influence for welded
structures of steel and consideration of bending
for welded structures of steel and of aluminium
Annex G (informative) - Enhancement of reference
value of the fatigue strength [Delta][sigma][c] for
load carrying T- and cruciform joints with double
fillet weld with or without partial penetration
Annex H (informative) - Application of structural
stress assessment for welded structures of steel
and aluminium
Annex I (informative) - Application of notch stress
assessment for welded structures of steel and
aluminium
Annex J (informative) - Example for fatigue assessment
Annex K (informative) - Determination of nominal
stresses in weld root of single sided partial
penetration welds
Bibliography
BS EN 17149.
| Committee |
RAE/3/-/11
|
| DocumentType |
Draft
|
| Pages |
134
|
| PublisherName |
British Standards Institution
|
| Status |
NA
|
| Standards | Relationship |
| PREN 17149 : DRAFT 2017 | Identical |
| ASTM E 446 : 2015 : REDLINE | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
| EN 12680-2:2003 | Founding - Ultrasonic examination - Part 2: Steel castings for highly stressed components |
| ASTM E 186 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings |
| EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN 15085-1:2007+A1:2013 | Railway applications - Welding of railway vehicles and components - Part 1: General |
| EN 12680-1:2003 | Founding - Ultrasonic examination - Part 1: Steel castings for general purposes |
| EN 485-2:2016 | Aluminium and aluminium alloys - Sheet, strip and plate - Part 2: Mechanical properties |
| DVS 0905:2017-02 | INDUSTRIELLE ANWENDUNG DES KERBSPANNUNGSKONZEPTES FUER DEN ERMUEDUNGSFESTIGKEITSNACHWEIS VON SCHWEISSVERBINDUNGEN |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| ISO 2394:2015 | General principles on reliability for structures |
| EN 586-2:1994 | Aluminium and aluminium alloys - Forgings - Part 2: Mechanical properties and additional property requirements |
| ASTM E 155 : 2015 : REDLINE | Standard Reference Radiographs for Inspection of Aluminum and Magnesium Castings |
| EN 15085-5:2007 | Railway applications - Welding of railway vehicles and components - Part 5: Inspection, testing and documentation |
| EN 1370:2011 | Founding - Examination of surface condition |
| EN 1706:2010 | Aluminium and aluminium alloys - Castings - Chemical composition and mechanical properties |
| EN 1371-1:2011 | Founding - Liquid penetrant testing- Part 1: Sand, gravity die and low pressure die castings |
| EN 12680-3:2011 | Founding - Ultrasonic testing - Part 3: Spheroidal graphite cast iron castings |
| EN 1563:2011 | Founding - Spheroidal graphite cast irons |
| EN 1369:2012 | Founding - Magnetic particle testing |
| ASTM E 280 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings |
| EN 12681:2003 | Founding - Radiographic examination |
| EN 12663-1:2010+A1:2014 | Railway applications - Structural requirements of railway vehicle bodies - Part 1: Locomotives and passenger rolling stock (and alternative method for freight wagons) |
| EN 15085-2:2007 | Railway applications - Welding of railway vehicles and components - Part 2: Quality requirements and certification of welding manufacturer |
| EN 12663-2:2010 | Railway applications - Structural requirements of railway vehicle bodies - Part 2: Freight wagons |
| EN 13749:2011 | Railway applications - Wheelsets and bogies - Method of specifying the structural requirements of bogie frames |
| EN 755-2:2016 | Aluminium and aluminium alloys - Extruded rod/bar, tube and profiles - Part 2: Mechanical properties |
| EN 15085-4:2007 | Railway applications - Welding of railway vehicles and components - Part 4: Production requirements |
| EN 15827:2011 | Railway applications - Requirements for bogies and running gears |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.