ANSI/AWWA C514 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
AIR VALVE AND VENT INFLOW PREVENTER ASSEMBLIES FOR POTABLE WATER DISTRIBUTION SYSTEM AND STORAGE FACILITIES
Hardcopy , PDF
English
01-11-2015
07-03-2022
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendix
A - Installation, Operation, and
Maintenance of Inflow Preventer
Assemblies
Specifies 1-in. (25-mm) through 12-in. (300-mm) air valve and vent inflow preventer assemblies designed for use on the outlet of potable water distribution system air valves furnished in accordance with ANSI/AWWA C512 or storage facility vent pipes.
| DocumentType |
Standard
|
| ISBN |
978-1-62576-120-0
|
| Pages |
28
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy |
| AWWA C207 : 2013 | STEEL PIPE FLANGES FOR WATERWORKS SERVICE, SIZES 4 IN. THROUGH 144 IN. (100 MM THROUGH 3,600 MM) |
| ASTM B 154 : 2016 : REDLINE | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
| AWWA C550 : 2017 | PROTECTIVE INTERIOR COATINGS FOR VALVES AND HYDRANTS |
| ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
| ASTM D 1149 : 2016-02 | TEST METHODS FOR RUBBER DETERIORATION - CRACKING IN AN OZONE CONTROLLED ENVIRONMENT |
| ASTM A 666 : 2015 : REDLINE | Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| ASME B16.1 : 2015 | Gray Iron Pipe Flanges and Flanged Fittings: Classes 25, 125, and 250 |
| ASME B1.20.1 : 2013(R2018) | PIPE THREADS, GENERAL PURPOSE (INCH) |
| ASTM D 3935 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 790 : 2017 : REDLINE | Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials |
| ASTM E 709 : 2015 : REDLINE | Standard Guide for Magnetic Particle Testing |
| ASTM A 276/A276M : 2017 : REDLINE | Standard Specification for Stainless Steel Bars and Shapes |
| AWWA C512 : 2015 | AIR-RELEASE, AIR/VACUUM, AND COMBINATION AIR VALVES FOR WATER AND WASTEWATER SERVICE |
| ASTM D 471 : 2016-02 | TEST METHOD FOR RUBBER PROPERTY - EFFECT OF LIQUIDS |
| ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.