ARMP-4 : 2008
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GUIDANCE FOR WRITING NATO R & M REQUIREMENTS DOCUMENTS
English
01-01-2008
14-08-2014
CHAPTER 1 - INTRODUCTION
101 GENERAL
102 PURPOSE
103 APPLICABILITY
104 RELATED DOCUMENTS
CHAPTER 2 - CONCEPTS AND FACTORS
201 GENERAL
202 IMPORTANCE OF USING QUANTITATIVE R&M REQUIREMENTS
203 NEED FOR TRACEABILITY
204 CONFIDENCE STATEMENTS
205 SELECTION OF R&M PARAMETERS
A GENERAL
B SYSTEM/EQUIPMENT R & M PARAMETERS
B.1 Availability
B.2 Mission Success
B.3 Maintenance Manpower
B.4 Logistic Support Cost
C SPECIFYING R&M REQUIREMENTS
C.1 Reliability
C.2 Maintainability
C.3 Combat Resilience
C.4 Testability
206 DUTY CYCLES AND ENVIRONMENTAL ENVELOPE
A DUTY CYCLES
B THE ENVIRONMENTAL ENVELOPE
207 MAINTENANCE CONCEPT
208 DEFINITIONS OF FAULT AND FAILURE
209 SOURCES OF INFORMATION
A OPERATIONAL INFORMATION
B MAINTENANCE PLANNING INFORMATION
210 SAFETY AND ASSOCIATED RISK ANALYSIS
211 R & M PROGRAMME PLANS
CHAPTER 3 - DEVELOPMENT OF THE R&M CONTENT OF THE
PHASE ARMAMENTS PROGRAMMING SYSTEM (PASS)
MILESTONES
301 GENERAL
302 THE R & M CONTENT OF THE NATO STAFF TARGET
A PRE-FEASIBILITY STUDIES
B FORMULATION OF THE R & M CONTENT OF THE STAFF
TARGET
303 THE R&M CONTENT OF THE NATO STAFF REQUIREMENT
A FEASIBILITY STUDIES
B FORMULATION OF THE R&M CONTENT OF THE NATO
STAFF REQUIREMENT
304 THE R&M CONTENT OF THE NATO DESIGN &
DEVELOPMENT OBJECTIVE AND THE DESIGN &
DEVELOPMENT SPECIFICATION
A PROJECT DEFINITION PHASE
B FORMULATION OF THE R&M CONTENT OF THE NATO
DESIGN & DEVELOPMENT OBJECTIVE AND THE DESIGN
& DEVELOPMENT SPECIFICATION
305 THE R&M CONTENT OF THE NATO PRODUCTION OBJECTIVE
AND THE PRODUCTION SPECIFICATION
A DESIGN & DEVELOPMENT PHASE
B FORMULATION OF THE R&M CONTENT OF THE NATO
PRODUCTION OBJECTIVE AND THE PRODUCTION
SPECIFICATION
306 THE R & M CONTENT OF THE NATO IN-SERVICE GOALS
A PRODUCTION PHASE
B FORMULATION OF THE R&M CONTENT OF THE NATO
IN-SERVICE GOALS
C IN-SERVICE PHASE
D R & M CHARACTERISTICS AND IMPACT ON THE
MAINTENANCE PLAN
ANNEX A - EXAMPLES OF QUANTITATIVE R&M REQUIREMENTS
ANNEX B - QUANTIFYING MAINTAINABILITY REQUIREMENTS
APPENDIX - MATHEMATICAL BACKGROUND TO THE LOG-NORMAL
DISTRIBUTION
Specifies the concepts and factors affecting the formulation of R&M requirements to assist operational requirements staff to define the basic R&M requirements, and the procurement agency to convert these requirements into contractually agreed specifications.
| DevelopmentNote |
Supersedes DEFSTAN 00-40(PT4)/2(2003). (02/2008)
|
| DocumentType |
Standard
|
| Pages |
55
|
| PublisherName |
NATO
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| DEFSTAN 00-49/2(2008) : 2008 | MOD GUIDE TO R&M TERMINOLOGY USED IN REQUIREMENTS |
| AAP-48 : 2013 | NATO SYSTEM LIFE CYCLE STAGES AND PROCESSES |
| DEFSTAN 00-40(PT5)/1(1989) : 1989 | RELIABILITY AND MAINTAINABILITY - PART 5: GUIDANCE ON R & M TRAINING (ARMP-5) |
| ARMP-9 : 2009 | GUIDE TO THE MANAGEMENT OF SOFTWARE R&M |
| DEFSTAN 00-41/3(1993) : 1993 | RELIABILITY AND MAINTAINABILITY MOD GUIDE TO PRACTICES AND PROCEDURES |
| STANAG 4457 : 0 | NATO GUIDE ON ENGINEERING NATION IN MULTINATIONAL JOINT PROGRAMMES |
| ARMP-8 : 1991 | RELIABILITY & MAINTAINABILITY (R&M) IN THE PROCUREMENT OF OFF-THE-SHELF (OTS) EQUIPMENT |
| DEFSTAN 00-40(PT6)/1(1988) : 1988 | RELIABILITY AND MAINTAINABILITY - PART 6: IN-SERVICE R & M |
| ARMP-6 : 2008 | GUIDANCE FOR MANAGING IN-SERVICE R&M |
| ARMP-5 : 1998 | GUIDANCE ON RELIABILITY AND MAINTAINABILITY TRAINING |
| ARMP-2 : 1993 | GENERAL APPLICATION GUIDANCE ON THE USE OF ARMP-1 |
| AQAP 159 : 2 | GUIDANCE FOR THE USE OF AQAP-150 |
| ARMP-7 : 2008 | NATO R&M TERMINOLOGY APPLICABLE TO ARMPS |
| AQAP 110 : 2 | NATO QUALITY ASSURANCE REQUIREMENTS FOR DESIGN, DEVELOPMENT AND PRODUCTION |
| STANAG 4174 : 2008 | ALLIED RELIABILITY AND MAINTAINABILITY PUBLICATIONS |
| ARMP-6 : 2008 | GUIDANCE FOR MANAGING IN-SERVICE R&M |
| AQAP 119 : 2 | NATO GUIDE TO AQAP-110, -120 AND -130 |
| AQAP 120 : 2 | NATO QUALITY ASSURANCE REQUIREMENTS FOR PRODUCTION |
| ARMP-1 : 2008 | NATO REQUIREMENTS FOR RELIABILITY AND MAINTAINABILITY |
| AQAP 150 : 2 | NATO QUALITY ASSURANCE REQUIREMENTS FOR SOFTWARE DEVELOPMENT |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.