AS 1163-1991

1 - AS 1163-1991 STRUCTURAL STEEL HOLLOW SECTIONS
4 - PREFACE
4 - CONTENTS
5 - 1 SCOPE
5 - 2 REFERENCED DOCUMENTS
5 - 3 DEFINITIONS
5 - 3.1 Batch
5 - 3.2 Cast analysis
5 - 3.3 Cold-formed hollow section
5 - 3.4 Longitudinal direction
5 - 3.5 Product analysis
5 - 3.6 Testing
5 - 3.7 Test piece
5 - 3.8 Test sample
5 - 3.9 Test specimen
5 - 3.10 Transverse direction
5 - 3.11 Unit
5 - 4 DESIGNATION
6 - 5 STEELMAKING PROCESS
6 - 6 CHEMICAL COMPOSITION
6 - 6.1 General
6 - 6.2 Cast analysis
6 - 6.3 Product analysis
6 - 7 DIMENSIONS, MASS AND GEOMETRICAL PROPERTIES
6 - 8 DIMENSIONAL TOLERANCES
6 - 8.1 Length
7 - 8.2 Cross-section
8 - 8.3 Straightness
8 - 8.4 Twist (rectangular sections)
8 - 9 MASS TOLERANCE
8 - 10 FREEDOM FROM DEFECTS
8 - 11 REMOVAL OF SURFACE DEFECTS
8 - 11.1 Grinding
8 - 11.2 Depositing weld metal
8 - 12 REMOVAL OF UPSET
8 - 13 MECHANICAL TESTING
8 - 13.1 General
8 - 13.2 Orientation of test pieces
8 - 13.3 Position and orientation of test piece
9 - 14 PREPARATION OF TEST PIECES FOR MECHANICAL TESTING
9 - 14.1 General
9 - 14.2 Tensile test pieces
9 - 14.3 Impact test piece
9 - 14.4 Ageing treatment
9 - 14.5 Cold flattening test
9 - 15 MECHANICAL TEST REQUIREMENTS
9 - 15.1 Tensile test
9 - 15.2 Impact test
10 - 15.3 Cold flattening test
10 - 16 MECHANICAL PROPERTIES
10 - 16.1 Tensile test
10 - 16.2 Impact test
10 - 16.3 Cold flattening test
10 - 17 ROUNDING OF NUMBERS
10 - 17.1 General
10 - 17.2 Tensile properties
10 - 18 MARKING
12 - APPENDIX A - PURCHASING GUIDELINES
12 - A1 INFORMATION TO BE SUPPLIED BY THE PURCHASER
12 - A2 SUPPLEMENTARY TESTS
12 - A2.1 Non-destructive testing
12 - A2.2 Independent test
12 - A3 CERTIFICATES OF COMPLIANCE AND TEST CERTIFICATES
12 - A3.1 Certificates of compliance
12 - A3. 2 Test certificates
12 - A4 INSPECTION
13 - APPENDIX B - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
13 - B1 SCOPE
13 - B2 STATISTICAL SAMPLING
13 - B3 PRODUCT CERTIFICATION- STANDARDSMARK
13 - B4 SUPPLIER’S QUALITY SYSTEM
13 - B5 OTHER MEANS OF ASSESSMENT
13 - B5.1 Sampling of tensile test, impact test and cold flattening test
14 - B5.2 Compliance
14 - B5.3 Retests
15 - APPENDIX C - DIMENSIONS AND PROPERTIES OF CROSS-SECTION
26 - APPENDIX D - METHOD FOR VERIFYING GRADE L0 COMPLIANCE OF THIN WALL SECTIONS
26 - D1 SCOPE
26 - D2 METHOD
26 - D3 BACKGROUND

Specifies the technical requirements for cold-formed steel hollow sections for structural purposes, for the six grades of steel that are suitable for welding. Grade C200 and all hot-formed grades have been deleted. It includes a new cold-formed grade C450 and grades with guaranteed impact performance at 0 degrees Celsius, namely C250L0 and C450L0. Tensile strengths of grades C250 and C350 are reduced to reflect the properties obtained on cold-formed sections.

This Standard specifies the requirements for cold-formed steel hollow sections for structural purposes, for the six grades of steel that are suitable for welding.NOTES:1 For guidelines on information to be supplied at the time of enquiry or order, see Appendix A.2 Alternative means for demonstrating compliance with this Standard are given in Appendix B.

First published as AS A177-1969.
Revised and redesignated AS 1163-1973.
AS A177 withdrawn 1976.
Second edition AS 1163-1981.
Third edition 1991.