AS/NZS 2210.1:1994

1 - AS/NZS 2210.1:1994 OCCUPATIONAL PROTECTIVE FOOTWEAR - GUIDE TO SELECTION, CARE AND USE
4 - PREFACE
5 - CONTENTS
6 - SECTION 1 SCOPE AND GENERAL
6 - 1.1 SCOPE
6 - 1.2 GENERAL PRINCIPLES
6 - 1.3 REFERENCED DOCUMENTS
6 - 1.4 DEFINITIONS
6 - 1.4.1 Attaching
6 - 1.4.2 Back (or quarter)
6 - 1.4.3 Blake sewing
6 - 1.4.4 Blind eyelet
6 - 1.4.5 Blocked
6 - 1. 4.6 Counter
7 - 1.4.7 Deep tread
7 - 1. 4.8 Facing
7 - 1.4.9 Fairstitched
7 - 1.4.10 Featherline
7 - 1.4.11 Feathered
7 - 1.4.12 Foxing strip
7 - 1.4.13 Full bellows tongue
7 - 1.4.14 Goodyear welted
7 - 1.4.15 Group
7 - 1.4.16 Half bellows tongue
7 - 1.4.17 Heel
7 - 1.4.18 Heel lifts
7 - 1.4.19 Injection moulded
7 - 1.4.20 Insole
7 - 1.4.21 Littleway
7 - 1.4.22 Mogul
7 - 1.4.23 Model
7 - 1.4.24 Occupational protective footwear
7 - 1.4.25 Outsole
7 - 1.4.26 Shank
7 - 1.4.27 Skived
7 - 1.4.28 Sole
7 - 1.4.29 Slugging wire
8 - 1.4.30 Stiffener
8 - 1.4.31 Style
8 - 1.4.32 Top lift
8 - 1.4.33 Touch and close fastener
8 - 1.4.34 Tread
8 - 1.4.35 Upper
8 - 1.4.36 Vamp
9 - SECTION 2 FOOT PROTECTION PROGRAM
9 - 2.1 IMPLEMENTATION
9 - 2.1.1 Administrative responsibility
9 - 2.1.2 Effectiveness
9 - 2.1.3 Consultation
9 - 2.1.4 Coordination
9 - 2.1.5 Educational program
10 - 2.2 PRE-SELECTION CRITERIA
10 - 2.2.1 Identification of hazards
10 - 2.2.2 Control of hazards
10 - 2.3 SELECTION OF PROTECTIVE FOOTWEAR
10 - 2.3.1 General
10 - 2.3.2 Selection factors
10 - 2.3.3 Tread design
12 - SECTION 3 CLASSIFICATION OF OCCUPATIONAL PROTECTIVE FOOTWEAR
12 - 3.1 GENERAL
12 - 3.2 SPECIAL FEATURES
12 - 3.2.1 Fuel-resistant outsoles
12 - 3.2.2 Penetration resistant midsoles
12 - 3.2.3 Electricity conductive properties
12 - 3.2.4 Anti-static properties
12 - 3.2.5 Special requirements
13 - SECTION 4 MATERIALS
13 - 4.1 GENERAL
13 - 4.2 UPPER MATERIALS
13 - 4.2.1 Leather
13 - 4.2.2 Synthetic-coated leather
13 - 4.2.3 Polyvinyl chloride (PVC) blends
13 - 4. 2.4 Fabrics
14 - 4.2.5 Lining materials
14 - 4.3 SOLING MATERIALS
14 - 4.3.1 Vulcanized nitrile rubber
14 - 4. 3.2 Natural rubber
14 - 4.3.3 Polyvinyl chloride blends
14 - 4.3.4 Polyurethane
14 - 4.3.5 Leather
15 - SECTION 5 FITTING AND CARE OF OCCUPATIONAL PROTECTIVE FOOTWEAR
15 - 5.1 FITTING
15 - 5.1.1 General
15 - 5.1.2 Benefits
15 - 5.2 CARE
15 - 5.2.1 Cleaning
15 - 5.2.2 Storage
15 - 5.2.3 Alterations
15 - 5.3 HYGIENE
15 - 5.4 CONDUCTIVE AND ANTI-STATIC PROPERTIES
15 - 5.4.1 General
15 - 5.4.2 Conductive properties
16 - 5.4.3 Anti-static
17 - APPENDIX A - FOOTWEAR CONSTRUCTION METHODS
20 - APPENDIX B - HAZARD IDENTIFICATION
21 - APPENDIX C - SELECTION GUIDE BASED ON APPLICATION
22 - APPENDIX D - SELECTION GUIDE BASED ON RESISTANCE TO CHEMICAL DEGRADATION
22 - D1 INTRODUCTION
22 - D2 SELECTION
26 - APPENDIX E - SELECTION GUIDE BASED ON THE SLIP-RESISTANCE CHARACTERISTICS OF SOLING MATERIALS

Provides users and purchasers of occupational protective footwear with recommended practices for the selection care and use of protective footwear in a wide range of primary, secondary and construction industries. Guidance for footwear care, fitting and foot protection programs is provided.

This Standard sets out the recommended practices for the selection, care and use of occupational protective footwear for the protection of feet in building and construction, underground working, mining, quarrying, forestry and other occupations with similar hazards.

For history before 1994 see Preface.
AS 2210-1980 and NZS 5845:1989 jointly revised in part and redesignated as Joint Standard AS/NZS 2210.1:1994.