AS/NZS 61000.3.11:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Electromagnetic compatibility (EMC) Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems - Equipment with rated current less than or equal to 75 A and subject to conditional connection (Reconfirmed 2013)
Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users
English
18-09-2002
23-06-2023
Specifies the limits of voltage changes, voltage fluctuations and flicker produced by electrical and electronic equipment having a rated input current from 16 A up to and including 75 A. This equipment is intended to be connected to public low-voltage distribution systems having nominal system voltages of between 220 V and 250 volt, line-to-neutral at 50 Hz and which is subject to conditional connection. This Standard is identical with and has been reproduced from IEC 61000-3-11:2000.
| Committee |
EL-034
|
| DocumentType |
Standard
|
| ISBN |
0 7337 4843 0
|
| Pages |
10
|
| ProductNote |
This standard has been reconfirmed in Australia in 2013 and remains current in New Zealand. Reconfirmation Notice 29-11-2013
|
| PublisherName |
Standards Australia
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of AS/NZS 61000 is concerned with the emission of voltage changes, voltage fluctuations and flicker produced by equipment and impressed on the public low-voltage supply system.It specifies the limits of voltage changes produced by equipment tested under specified conditions.This part of AS/NZS 61000 is primarily applicable to electrical and electronic equipment having a rated input current from 16 A up to and including 75 A, which is intended to be connected to public low-voltage distribution systems having nominal system voltages of between 220 V and 250 V, line-to-neutral at 50 Hz, and which is subject to conditional connection.This part of AS/NZS 61000 is also applicable to equipment within the scope of IEC 61000-3-3 that does not meet the limits when tested or evaluated with reference impedance Zref and is therefore subject to conditional connection. Equipment which meets the requirements of IEC 61000-3-3, is excluded from this part of AS/NZS 61000.Equipment tests made in accordance with this part of AS/NZS 61000 are type tests.NOTE The flicker limits specified in this part, being the same as those in IEC 61000-3-3, are based on the subjective severity of the flicker imposed on the light from 230 V/60 W coiled-coil filament lamps when subjected to fluctuations of the supply voltage. For systems with nominal voltages less than 220 V, line-to-neutral and/or frequency of 60 Hz, the limits and reference circuit values are under consideration.
| Standards | Relationship |
| IEC 61000-3-11:2000 | Identical |
First published as AS/NZS 61000.3.11:2002.
| AS/NZS 61000.3.3:1998 | Electromagnetic compatibility (EMC) Limits - Limitation of voltage fluctuations and flicker in low-voltage supply systems for equipment with rated current less than or equal to 16 A |
| AS/NZS 61000.6.3:2007 | Electromagnetic compatibility (EMC) Generic standards - Emission standard for residential, commercial and light-industrial environments |
| AS/NZS 61000.6.3:2012 | Electromagnetic compatibility (EMC) Generic standards - Emission standard for residential, commercial and light-industrial environments |
| AS/NZS 61058.1:2008 | Switches for appliances General requirements (IEC 61058-1, Ed. 3.1 (2000), MOD) |
| SA/SNZ TR IEC 61000.3.14:2013 | Electromagnetic compatibility (EMC) Limits - Assessment of emission limits for harmonics, interharmonics, voltage fluctuations and unbalance for the connection of disturbing installations to LV power systems |
| AS 2703-2008 | Vehicle loop detector sensors |
| TR IEC 61000.1.4:2012 | Electromagnetic compatibility (EMC) General - Historical rationale for the limitation of power-frequency conducted harmonic current emissions from equipment, in the frequency range up to 2 kHz |
| AS/NZS 4613:2017 | Automotive equipment - Brake force measuring instruments |
| AS/NZS 61000.3.3:2003 | Electromagnetic compatibility (EMC) Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current less than or equal to 16A per phase and not subject to conditional connection |
| AS/NZS 4871.1:2010 | Electrical equipment for mines and quarries General requirements |
| SA/SNZ TS IEC 61000.3.5:2013 | Electromagnetic compatibility (EMC) Limits - Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 75 A |
| AS/NZS 61000.3.3:2006 | Electromagnetic compatibility (EMC) Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current per phase and not subject to conditional connection |
| AS 2067-2008 | Substations and high voltage installations exceeding 1 kV a.c. |
| AS/NZS 61000.3.3:2012 | Electromagnetic compatibility (EMC) Limits - Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≤16 A per phase and not subject to conditional connection |
| AS 61800.3-2005 | Adjustable speed electrical power drive systems EMC requirements and specific test methods |
| AS/NZS 61000.4.15:2012 | Electromagnetic compatibility (EMC) Testing and measurement techniques - Flickermeter - Functional and design specifications |
| SA/SNZ TR IEC 60725:2013 | Consideration of reference impedances and public supply network impedances for use in determining the disturbance characteristics of electrical equipment having a rated current ≤75 A per phase |
| AS/NZS 4871.1:2012 | Electrical equipment for mines and quarries General requirements |
| AS/NZS 3007:2013 | Electrical equipment in mines and quarries - Surface installations and associated processing plant |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.