ASTM C 39/C39M : 2023
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
English
01-12-2023
03-04-2026
| Committee |
C 09
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
1.1This test method covers determination of compressive strength of cylindrical concrete specimens such as molded cylinders and drilled cores. It is limited to concrete having a density in excess of 800 kg/m3 [50 lb/ft3].
1.2The values stated in either SI units or inch-pound units are to be regarded separately as standard. The inch-pound units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.(Warning—Means should be provided to contain concrete fragments during sudden rupture of specimens. Tendency for sudden rupture increases with increasing concrete strength and it is more likely when the testing machine is relatively flexible. The safety precautions given in R0030 are recommended.)
1.4The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| ASTM C 882/C882M : 2023 | Standard Test Method for Bond Strength of Bonding Systems Used With Concrete By Slant Shear |
| ASTM C 928/C928M : 2020 : REV A | Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs |
| ASTM C 465 : 2023 | Standard Specification for Processing Additions for Use in the Manufacture<brk/> of Hydraulic Cements |
| ASTM C 935 : 2019 | Standard Specification for General Requirements for Prestressed Concrete Poles Statically Cast |
| ASTM A 979/A979M : 2003 : R2019 | Standard Specification for Concrete Pavements and Linings Installed in Corrugated Steel Structures in the Field |
| ASTM C 1504M : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains (Metric) (Withdrawn 2025) |
| ASTM C 780 : 2023 | Standard Test Methods for Preconstruction and Construction Evaluation of Mortars for Plain and Reinforced Unit Masonry |
| ASTM F 2551 : 2009 : R2023 | Standard Practice for Installing a Protective Cementitious Liner System in Sanitary Sewer Manholes |
| ASTM C 1439 : 2019 | Standard Test Methods for Evaluating Latex and Powder Polymer Modifiers for use in Hydraulic Cement Concrete and Mortar |
| ASTM C 494/C494M : 2019 : EDT 1 | Standard Specification for Chemical Admixtures for Concrete |
| ASTM C 495/C495M : 2012 : R2019 | Standard Test Method for Compressive Strength of Lightweight Insulating Concrete |
| ASTM C 497M : 2020 : REV A | Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile (Metric) (Withdrawn 2025) |
| ASTM C 233/C233M : 2018 | Standard Test Method for Air-Entraining Admixtures for Concrete |
| ASTM C 563 : 2020 | Standard Guide for Approximation of Optimum SO<inf>3</inf> in Hydraulic Cement |
| ASTM C 469/C469M : 2022 | Standard Test Method for Static Modulus of Elasticity and Poisson's Ratio of Concrete in Compression |
| ASTM C 94/C94M : 2023 | Standard Specification for Ready-Mixed Concrete |
| ASTM C 387/C387M : 2023 | Standard Specification for Packaged, Dry, Combined Materials for Concrete and High Strength Mortar |
| ASTM C 1602/C1602M : 2022 | Standard Specification for Mixing Water Used in the Production of Hydraulic Cement Concrete |
| ASTM C 497 : 2020 : EDT 1 | Standard Test Methods for Concrete Pipe, Concrete Box Sections, Manhole Sections, or Tile |
| ASTM D 7147 : 2021 | Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers |
| ASTM D 6449 : 1999 : R2015 : EDT 1 | Standard Test Method for Flow of Fine Aggregate Concrete for Fabric Formed Concrete (Flow Cone Method) (Withdrawn 2024) |
| ASTM C 226 : 2022 | Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement |
| ASTM F 1741 : 2022 | Standard Practice for Installation of Machine Spiral Wound Poly (Vinyl Chloride) (PVC) Liner Pipe for Rehabilitation of Existing Sewers and Conduits |
| ASTM C 882/C882M : 2020 | Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear |
| ASTM C 1077 : 2017 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 1504 : 2020 | Standard Specification for Manufacture of Precast Reinforced Concrete Three-Sided Structures for Culverts and Storm Drains |
| ASTM C 1074 : 2019 : EDT 1 | Standard Practice for Estimating Concrete Strength by the Maturity Method |
| ASTM D 7913/D7913M : 2014 : R2020 | Standard Test Method for Bond Strength of Fiber-Reinforced Polymer Matrix Composite Bars to Concrete by Pullout Testing |
| ASTM C 688 : 2022 | Standard Specification for Functional Additions for Use in Hydraulic Cements |
| ASTM C 1709 : 2022 | Standard Guide for Evaluation of Alternative Supplementary Cementitious Materials (ASCM) for Use in Concrete |
| ASTM D 8329 : 2021 | Standard Test Method for Determination of Water/Cementitious Materials Ratio for Geosynthetic Cementitious Composite Mats (GCCMs) and Measurement of the Compression Strength of the Cementitious Material Contained Within |
| ASTM C 330/C330M : 2023 | Standard Specification for Lightweight Aggregates for Structural Concrete |
| AASHTO R 18:2018(R2022) | Establishing and Implementing a Quality Management System for Construction Materials Testing Laboratories |
| ACI CODE-376:2023(IN-LB) | Refrigerated Liquefied Gas Containment for Concrete Structures— Code Requirements and Commentary |
| ASTM E 18 : 2024 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM C 617/C617M : 2015 | Standard Practice for Capping Cylindrical Concrete Specimens |
| ASTM C 1077 : 2024 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 670 : 2024 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM E 18 : 2022 | Standard Test Methods for Rockwell Hardness of Metallic Materials |
| ASTM C 1077 : 2017 | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
| ASTM C 670 : 2024 : REV A | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
| ASTM C 670 : 2015 | Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.