• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 6600 : 2000 : R2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Evaluating Test Sensitivity for Rubber Test Methods
Available format(s)

Hardcopy , PDF

Superseded date

04-08-2023

Language(s)

English

Published date

01-11-2013

CONTAINED IN VOL. 09.01, 2017 Specifies testing to evaluate of chemical constituents, chemical and physical properties of compounding materials, and compounded and cured rubbers, which may frequently be conducted by one or more test methods.

1.1This practice covers testing to evaluate chemical constituents, chemical and physical properties of compounding materials, and compounded and cured rubbers, which may frequently be conducted by one or more test methods. When more than one test method is available, two questions arise: Which test method has the better (or best) response to or discrimination for the underlying fundamental property being evaluated? and Which test method has the least error? These two characteristics collectively determine one type of technical merit of test methods that may be designated as test sensitivity.

1.2Although a comprehensive and detailed treatment, as given by this practice, is required for a full appreciation of test sensitivity, a simplified conceptual definition may be given here. Test sensitivity is the ratio of discrimination power for the fundamental property evaluated to the measurement error or uncertainty, expressed as a standard deviation. The greater the discriminating power and the lower the test error, the better is the test sensitivity. Borrowing from the terminology in electronics, this ratio has frequently been called the signal-to-noise ratio; the signal corresponding to the discrimination power and the noise corresponding to the test measurement error. Therefore, this practice describes how test sensitivity, generically defined as the signal-to-noise ratio, may be evaluated for test methods used in the rubber manufacturing industry, which measure typical physical and chemical properties, with exceptions as noted in 1.3.

1.3This practice does not address the topic of sensitivity for threshold limits or minimum detection limits (MDL) in such applications as (1) the effect of intentional variations of compounding materials on measured compound properties or (2) the evaluation of low or trace constituent levels. Minimum detection limits are the subject of separate standards.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5The content of this practice is as follows:

Section

Scope

1

Referenced Documents

2

Terminology

3

Summary of Practice

4

Significance and Use

5

Measurement Process

6

Development of Test Sensitivity Concepts
(Absolute and Relative Test Sensitivity, Limited and Extended Range Test Sensitivity, Uniform and Nonuniform Test Sensitivity)

7

Steps in Conducting a Test Sensitivity Evaluation Program

8

Report for Test Sensitivity Evaluation

9

Keywords

10

Annex A1—Background on: Use of Linear Regression Analysis and Precision of Test Sensitivity Evaluation

Appendix X1—Two Examples of Relative Test Sensitivity Evaluation:

Relative Test Sensitivity: Limited Range—Three Processability Tests

Relative Test Sensitivity: Extended Range—Compliance versus Modulus

Appendix X2—Background on: Transformation of Scale and Derivation of Absolute Sensitivity for a Simple Analytical Test


Committee
D 11
DocumentType
Standard Practice
Pages
16
ProductNote
Reconfirmed 2013
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4483 : 2018 Standard Practice for Evaluating Precision for Test Method Standards in the Rubber and Carbon Black Manufacturing Industries
ASTM D 7605 : 2011 : R2016 Standard Test Method for Thermoplastic Elastomers—Measurement of Polymer Melt Rheological Properties and Congealed Dynamic Properties Using Rotorless Shear Rheometers

ASTM D 4483 : 2014-02 PRACTICE FOR EVALUATING PRECISION FOR TEST METHOD STANDARDS IN THE RUBBER AND CARBON BLACK MANUFACTURING INDUSTRIES

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.