• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM D 7264/D7264M : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials
Available format(s)

Hardcopy , PDF

Superseded date

19-02-2021

Language(s)

English

Published date

06-05-2015

1.1 This test method determines the flexural stiffness and strength properties of polymer matrix composites.

1.1This test method determines the flexural stiffness and strength properties of polymer matrix composites.

1.1.1Procedure A—A three-point loading system utilizing center loading on a simply supported beam.

1.1.2Procedure B—A four-point loading system utilizing two load points equally spaced from their adjacent support points, with a distance between load points of one-half of the support span.

Note 1:Unlike Test Method D6272, which allows loading at both one-third and one-half of the support span, in order to standardize geometry and simplify calculations this standard permits loading at only one-half the support span.

1.2For comparison purposes, tests may be conducted according to either test procedure, provided that the same procedure is used for all tests, since the two procedures generally give slightly different property values.

1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
D 30
DocumentType
Test Method
Pages
10
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 7905/D7905M : 2019 : EDT 1 Standard Test Method for Determination of the Mode II Interlaminar Fracture Toughness of Unidirectional Fiber-Reinforced Polymer Matrix Composites
ASTM D 4762 : 2018 Standard Guide for Testing Polymer Matrix Composite Materials

ASTM D 6856 : 2003 Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials
ASTM D 6272 : 2010 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3878 : 2002 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2015 Standard Terminology for Composite Materials
ASTM E 1434 : 2000 : R2013 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases (Withdrawn 2015)
ASTM D 3878 : 2019 Standard Terminology for Composite Materials
ASTM D 3878 : 2000 Standard Terminology Composite Materials
ASTM D 6272 : 2017 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3878 : 2003 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2016 Standard Terminology for Composite Materials
ASTM E 1309 : 2000 Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases
ASTM D 3878 : 2019 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 2020 : REV A Standard Terminology for Composite Materials
ASTM D 3878 : 1998 Standard Terminology Composite Materials
ASTM D 3878 : 2018 Standard Terminology for Composite Materials
ASTM E 1434 : 2000 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases
ASTM D 3878 : 2002 Standard Terminology for Composite Materials
ASTM D 6272 : 2017 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 6272 : 2002 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 6272 : 2002 : R2008 : EDT 1 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3878 : 2004 Standard Terminology for Composite Materials
ASTM D 3878 : 2007 : R2013 Standard Terminology for Composite Materials
ASTM D 6856 : 2003 : R2008 Standard Guide for Testing Fabric-Reinforced "Textile" Composite Materials
ASTM E 1309 : 2000 : R2011 Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases (Withdrawn 2015)
ASTM D 3878 : 2020 : REDLINE Standard Terminology for Composite Materials
ASTM D 3878 : 2020 Standard Terminology for Composite Materials
ASTM D 3878 : 2003 Standard Terminology for Composite Materials
ASTM D 3878 : 2007 Standard Terminology for Composite Materials
ASTM E 1309 : 2000 : R2005 Standard Guide for Identification of Fiber-Reinforced Polymer-Matrix Composite Materials in Databases
ASTM D 6272 : 2000 Standard Test Method for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D 3878 : 2004 : REV A Standard Terminology for Composite Materials
ASTM E 1434 : 2000 : R2006 Standard Guide for Recording Mechanical Test Data of Fiber-Reinforced Composite Materials in Databases
ASTM D 3878 : 2001 Standard Terminology Composite Materials

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.