• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 1077 : 2014 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Test Methods for Estimating the Depth of Decarburization of Steel Specimens
Available format(s)

PDF

Language(s)

English

Published date

21-03-2014

CONTAINED IN VOL. 03.01, 2015 Defines procedures for estimating depth of decarburization of steels irrespective of the composition, matrix microstructure, or section shape.

1.1These test methods cover procedures for estimating the depth of decarburization of steels irrespective of the composition, matrix microstructure, or section shape. The following basic procedures may be used:

1.1.1Screening methods.

1.1.2Microscopical methods.

1.1.3Microindentation hardness methods.

1.1.4Chemical analysis methods.

1.2In case of a dispute, the rigorous quantitative or lineal analysis method (see 7.3.5 and 7.3.6) shall be the referee method. These methods can be employed with any cross-sectional shape. The chemical analytical methods generally reveal a greater depth of decarburization than the microscopical methods but are limited to certain simple shapes and by availability of equipment. These techniques are generally reserved for research studies. The microindentation hardness method is suitable for accurate measurements of hardened structures with relatively homogeneous microstructures.

1.3The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
E 04
DocumentType
Redline
Pages
11
PublisherName
American Society for Testing and Materials
Status
Current

MIL-S-6758 Revision B:1993 STEEL, CHROME-MOLYBDENUM (4130) BARS AND REFORGING STOCK (AIRCRAFT QUALITY)
SAE AMS 6527 : 2018 STEEL, BARS AND FORGINGS, 2.0CR - 10NI - 14CO - 1.0MO (0.15 - 0.19C), VACUUM MELTED, NORMALIZED AND OVERAGED
ASTM A 485 : 2017 : REDLINE Standard Specification for High Hardenability Antifriction Bearing Steel
MIL-DTL-12560 Revision K:2013 ARMOR PLATE, STEEL, WROUGHT, HOMOGENEOUS (FOR USE IN COMBAT-VEHICLES AND FOR AMMUNITION TESTING)
SAE AMS 6411 : 2018 STEEL BARS, FORGINGS, AND TUBING, 0.88CR - 1.8NI - 0.42MO - 0.08V (0.28 - 0.33C) (4330 MOD) CONSUMABLE ELECTRODE REMELTED
SAE AMS 6303 : 2018 STEEL BARS AND FORGINGS, LOW ALLOY, HEAT-RESISTANT, 0.65SI - 1.25CR - 0.50MO - 0.85V (0.25 - 0.30C)
SAE AMS 6475 : 2013 STEEL, NITRIDING, BARS, FORGINGS, AND TUBING, 1.1CR - 3.5NI - 0.25MO - 1.2AL (0.21 - 0.26C)
AGMA 2004 : C GEAR MATERIALS, HEAT TREATMENT AND PROCESSING MANUAL
SAE AMS 6408 : 2018 STEEL, HOTWORK TOOL, BARS AND FORGINGS, 5.25CR - 1.5MO - 1.0V (0.35-0.45C) (H-13), ELECTROSLAG REMELTED (ESR) OR CONSUMABLE ELECTRODE VACUUM ARC REMELTED (VAR), ANNEALED
ASTM A 295 : 1998 Standard Specification for High-Carbon Anti-Friction Bearing Steel
ASTM A 756 : 2017 : REDLINE Standard Specification for Stainless Anti-Friction Bearing Steel
FF-O-601 Revision F:1990 OPENERS, CAN, HAND AND MOUNTED
ASTM E 3 : 2011 : R2017 Standard Guide for Preparation of Metallographic Specimens
SAE AMS 6360 : 2013 STEEL TUBING, SEAMLESS, 0.95CR - 0.20MO (0.28 - 0.33C) (SAE 4130), NORMALIZED OR STRESS RELIEVED
ASTM B 874 : 1996 : R2013 Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
SAE AMS 6348 : 2013 STEEL, BARS, 0.95CR - 0.20MO (0.28 TO 0.33C) (SAE 4130), NORMALIZED
ASTM B 874 : 1996 : R2003 Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
ASTM B 874 : 1996 : R2008 Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
ASTM E 3 : 2011 Standard Guide for Preparation of Metallographic Specimens
SAE AMS S 6758 : 2017 STEEL, CHROME-MOLYBDENUM (4130) BARS AND REFORGING STOCK (AIRCRAFT QUALITY)
A-A-52202 Revision C:2012 OPENER, CAN, HAND, FOR SQUARE AND ROUND FOOD CANS
AGMA 942 : A2012(R2017) METALLURGICAL SPECIFICATIONS FOR POWDER METALLURGY, PM, STEEL GEARING
SAE AMS 6532 : 2014 STEEL, BARS AND FORGINGS, 3.1CR - 11.5NI - 13.5CO - 1.2MO (0.21 - 0.25C) VACUUM MELTED, NORMALIZED AND OVERAGED, PRECIPITATION HARDENABLE
SAE AMS 6558 : 2013 STEEL, BARS, WIRE, AND FORGINGS 10.5MO - 6W - 3.75CR - 2V (1.25 - 1.40C) POWDER METALLURGY PRODUCT HOT ISOSTATICALLY PRESSED
AGMA 923 : B METALLURGICAL SPECIFICATIONS OF STEEL GEARING
IFI 140 : 2000 CARBON AND ALLOY STEEL WIRE, RODS AND BARS FOR MECHANICAL FASTENERS
SAE AMS 6557 : 2013 STEEL, BARS, WIRE, AND FORGINGS, 9V - 5.25CR - 1.3MO (1.80 - 1.95C), POWDER METALLURGY PRODUCT, HOT ISOSTATICALLY PRESSED
SAE AMS 6448 : 2013 STEEL, BARS, FORGINGS AND TUBING 0.95CR - 0.22V (0.48 - 0.53C) (SAE 6150)
SAE AMS 6346 : 2013 STEEL BARS, 0.95CR - 0.20MO (0.28 TO 0.33C) (SAE 4130), HARDENED AND TEMPERED, 125 KSI (862 MPA) TENSILE STRENGTH
SAE AMS 5352 : 2015 STEEL, CORROSION-RESISTANT, INVESTMENT CASTINGS, 17CR - 0.55MO (0.95 - 1.20C), ANNEALED
SAE AMS 6560 : 2013 STEEL BARS, WIRE AND FORGINGS 10CO - 7MO - 6V - 6W - 4CR (2.2 - 2.4C) PREMIUM AIRCRAFT-QUALITY FOR BEARING APPLICATIONS INERT GAS ATOMIZED AND HOT ISOSTATICALLY PRESSED CONSOLIDATED
ASTM A 295/A295M : 2014 : REDLINE Standard Specification for High-Carbon Anti-Friction Bearing Steel
ASTM B 874 : 1996 Standard Specification for Chromium Diffusion Coating Applied by Pack Cementation Process
ASTM A 534 : 2017 : REDLINE Standard Specification for Carburizing Steels for Anti-Friction Bearings
SAE AMS 6454 : 2011 STEEL, SHEET, STRIP, AND PLATE, 1.8NI - 0.80CR - 0.25MO (0.38 - 0.43C) (SAE 4340) VACUUM CONSUMABLE ELECTRODE REMELTED
SAE AMS 6559 : 2013 STEEL, BARS, WIRE, AND FORGINGS 9.75V - 5.25CR - 1.3MO (2.40 - 2.55C) POWDER METALLURGY PRODUCT HOT ISOSTATICALLY PRESSED
SAE AMS 6556 : 2013 STEEL, BARS, WIRE, AND FORGINGS, 8V - 4CR - 4W - 3MO (2.45 - 2.55C), POWDER METALLURGY PRODUCT, HOT ISOSTATICALLY PRESSED

ASTM E 1951 : 2014 : REDLINE Standard Guide for Calibrating Reticles and Light Microscope Magnifications
ASTM E 7 : 2017 : REDLINE Standard Terminology Relating to Metallography
ASTM E 415 : 2017 : REDLINE Standard Test Method for Analysis of Carbon and Low-Alloy Steel by Spark Atomic Emission Spectrometry
ASTM E 384 : 2017 : REDLINE Standard Test Method for Microindentation Hardness of Materials
ASTM E 340 : 2015 : REDLINE Standard Practice for Macroetching Metals and Alloys
ASTM E 350 : 2012-09 TEST METHODS FOR CHEMICAL ANALYSIS OF CARBON STEEL, LOW-ALLOY STEEL, SILICON ELECTRICAL STEEL, INGOT IRON, AND WROUGHT IRON

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.