• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 220 : 2013 : REDLINE

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Calibration of Thermocouples By Comparison Techniques

Available format(s)

PDF

Superseded date

27-01-2020

Language(s)

English

Published date

01-11-2013

CONTAINED IN VOL. 14.03, 2017 Specifies the principles, apparatus, and procedure for calibrating thermocouples by comparison with a reference thermometer.

1.1This test method describes the principles, apparatus, and procedure for calibrating thermocouples by comparison with a reference thermometer. Calibrations are covered over temperature ranges appropriate to the individual types of thermocouples within an overall range from approximately −195 to 1700 °C (−320 to 3100 °F).

1.2In general, this test method is applicable to unused thermocouples. This test method does not apply to used thermocouples due to their potential material inhomogeneity—the effects of which cannot be identified or quantified by standard calibration techniques. Thermocouples with large-diameter thermoelements and sheathed thermocouples may require special care to control thermal conduction losses.

1.3In this test method, all values of temperature are based on the International Temperature Scale of 1990. See Guide E1594.

1.4This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.

Committee
E 20
DocumentType
Redline
Pages
17
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM C 24 : 2009 : R2013 Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High Alumina Refractory Materials
ASTM A 1080 : 2015 : REDLINE Standard Practice for Hot Isostatic Pressing of Steel, Stainless Steel, and Related Alloy Castings
ASTM D 6007 : 2014 : REDLINE Standard Test Method for Determining Formaldehyde Concentrations in Air from Wood Products Using a Small-Scale Chamber
BS ISO 13573:2012 Corrosion of metals and alloys. Test method for thermal-cycling exposure testing under high-temperature corrosion conditions for metallic materials
ISO/TTA 5:2007 Code of practice for creep/fatigue testing of cracked components
03/301335 DC : DRAFT JAN 2003 ISO 15379-2 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - CATHODE BLOCKS - PART 2: DETERMINATION OF THE EXPANSION DUE TO SODIUM PENETRATION WITHOUT APPLICATION OF PRESSURE
ASTM E 2730 : 2010 : R2015 : EDT 2 Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits
ASTM D 6200 : 2001 : R2017 Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis
BS ISO 21608:2012 Corrosion of metals and alloys. Test method for isothermalexposure oxidation testing under high-temperature corrosion conditions for metallic materials
API 10 : 1990 SPECIFICATION FOR MATERIALS AND TESTING FOR WELL CEMENTS
13/30259829 DC : 0 BS ISO 17245 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR HIGH-TEMPERATURE CORROSION TESTING OF METALLIC MATERIALS BY IMMERSING IN MOLTEN SALT OR OTHER LIQUIDS UNDER STATIC CONDITIONS
03/301338 DC : DRAFT JAN 2003 ISO 20202 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - COLD AND TEPID RAMMING PASTES - PREPARATION OF BAKED TEST SPECIMENS AND DETERMINATION OF BAKING LOSS
BS ISO 17248:2015 Corrosion of metals and alloys. Test method for high temperature corrosion testing of metallic materials by embedding in salt, ash, or other solids
ASTM D 6200 : 2001 : R2007 Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis
API 10A : 2011 SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING
08/30165493 DC : DRAFT FEB 2008 BS EN ISO 10426-1 - PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION
ASTM E 585/E585M : 2012-06 SPECIFICATION FOR COMPACTED MINERAL-INSULATED, METAL-SHEATHED, BASE METAL THERMOCOUPLE CABLE
ASTM F 2082 : 2015 Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery
ISO 15379-2:2015 Carbonaceous materials for the production of aluminium — Cathode block materials — Part 2: Determination of the expansion due to sodium penetration without application of pressure
ASTM E 228 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Solid Materials With a Push-Rod Dilatometer
AASHTO T 366 : 2017 METHOD OF TEST FOR APPARENT VISCOSITY OF HOT-POURED ASPHALT CRACK SEALANT USING ROTATIONAL VISCOMETER
AASHTO TP 90 : 2010 : R2013 METHOD OF TEST FOR MEASURING INTERFACIAL FRACTURE ENERGY OF HOT-POURED CRACK SEALANT USING A BLISTER TEST
ISA 67.06.01 : 2002 PERFORMANCE MONITORING FOR NUCLEAR SAFETY-RELATED INSTRUMENT CHANNELS IN NUCLEAR POWER PLANTS
API 10A REDLINE : 2010 SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING
ASTM D 4693 : 2007 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM C 372 : 1994 : R2007 Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
ASTM E 1159 : 2015 : REDLINE Standard Specification for Thermocouple Materials, Platinum-Rhodium Alloys, and Platinum
ASTM C 621 : 2009 Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass
ISA MC96.1 : 1982 TEMPERATURE MEASUREMENT THERMOCOUPLES
ASTM D 5110 : 1998 : R2017 Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry
ASTM F 689 : 1997 : R2011 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings (Withdrawn 2017)
AASHTO T 48 : 2006 : R2010 METHOD OF TEST FOR FLASH AND FIRE POINTS BY CLEVELAND OPEN CUP
ASTM C 436 : 1983 Method of Test for Reheat Change of Carbon Refractory Brick and Shapes (Withdrawn 1988)
ASTM D 7646 : 2010 Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants for Aluminum Alloys by Cooling Curve Analysis
ASTM C 965 : 1996 : R2012 Standard Practice for Measuring Viscosity of Glass Above the Softening Point
ASTM A 991/A991M : 2017 : REDLINE Standard Test Method for Conducting Temperature Uniformity Surveys of Furnaces Used to Heat Treat Steel Products
ASTM E 235/E235M : 2012 : R2018 Standard Specification for Type K and Type N Mineral-Insulated, Metal-Sheathed Thermocouples for Nuclear or for Other High-Reliability Applications
ASTM D 6200 : 2001 Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis
ASTM C 202 : 1993 : R2004 Standard Test Method for Thermal Conductivity of Refractory Brick
ASTM C 202 : 1993 : R1998 Standard Test Method for Thermal Conductivity of Refractory Brick
ASTM E 1253 : 2013 : REDLINE Standard Guide for Reconstitution of Irradiated Charpy-Sized Specimens
ASTM E 207 : 2008 : R2015 : EDT 1 Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison with a Reference Thermoelement of Similar EMF-Temperature Properties
ASTM D 6374 : 2012 Standard Test Method for Volatile Matter in Green Petroleum Coke Quartz Crucible Procedure
ASTM D 4693 : 2007 : R2017 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM C 202 : 1993 : R2013 Standard Test Method for Thermal Conductivity of Refractory Brick
ASTM E 1457 : 2015 : REDLINE Standard Test Method for Measurement of Creep Crack Growth Times in Metals
ASTM C 1366 : 2004 : R2009 Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures
BS EN ISO 10426-2:2003 Petroleum and natural gas industries. Cements and materials for well cementing Testing of well cements
SAE J 2020 : 2016 ACCELERATED EXPOSURE OF AUTOMOTIVE EXTERIOR MATERIALS USING A FLUORESCENT UV AND CONDENSATION APPARATUS
MIL-STD-1312-17 Base Document:1985 FASTENER TEST METHODS, METHOD 17, STRESS RELATION
ASME BPE : 2016 BIOPROCESSING EQUIPMENT
ASTM C 1211 : 2018 : REDLINE Standard Test Method for Flexural Strength of Advanced Ceramics at Elevated Temperatures
ASTM C 201 : 1993 : R2013 Standard Test Method for Thermal Conductivity of Refractories
API MPMS CHAPTER 19.3 PART D : 2001(R2012) MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART D - FUGITIVE EMISSIONS TEST METHOD OF DECK-SEAM LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS
ISO 17224:2015 Corrosion of metals and alloys Test method for high temperature corrosion testing of metallic materials by application of a deposit of salt, ash, or other substances
BS ISO 15379-2:2015 Carbonaceous materials for the production of aluminium. Cathode block materials Determination of the expansion due to sodium penetration without application of pressure
API MPM CH19.3D:2001 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART D - FUGITIVE EMISSIONS TEST METHOD OF DECK-SEAM LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS
API MPM CH19.3C : 1998(R2018) MANUAL OF PETROLEUM MEASUREMENT STANDARDS - EVAPORATIVE LOSS MEASUREMENT - WEIGHT LOSS TEST METHOD FOR THE MEASUREMENT OF RIM-SEAL LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS
I.S. EN ISO 10426-1:2009 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION (ISO 10426-1:2009)
ASTM C 16 : 2003 : R2012 : EDT 2 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
API MPM CH19.3C : 1998(R2012) MANUAL OF PETROLEUM MEASUREMENT STANDARDS - EVAPORATIVE LOSS MEASUREMENT - WEIGHT LOSS TEST METHOD FOR THE MEASUREMENT OF RIM-SEAL LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS
ASTM C 1465 : 2008 : R2013 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
ASTM C 767 : 1993 : R2013 Standard Test Method for Thermal Conductivity of Carbon Refractories
API 10B-6:2010 RECOMMENDED PRACTICE ON DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATIONS
03/301339 DC : DRAFT JAN 2003 ISO 14428 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - COLD AND TEPID RAMMING PASTES - DETERMINATION OF EXPANSION/SHRINKAGE DURING BAKING
ASTM D 5110 : 1998 Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry
ASTM E 839 : 2011 Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple Cable
ASTM F 689 : 1997 : R2004 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings
ASTM C 16 : 2003 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
ASTM D 6482 : 2006 Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method)
ASTM E 696 : 2007 Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire
ASTM C 1465 : 2008 : R2013 : EDT 1 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
AASHTO T 301 : 2013 METHOD OF TEST FOR ELASTIC RECOVERY TEST OF ASPHALT MATERIALS BY MEANS OF A DUCTILOMETER
ASTM C 372 : 1994 : R2001 Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
AASHTO T 300 : 2011 METHOD OF TEST FOR FORCE DUCTILITY TEST OF ASPHALT MATERIALS
ASTM C 1276 : 1994 : R2005 Standard Test Method for Measuring the Viscosity of Mold Powders Above Their Melting Point Using a Rotational Viscometer (Withdrawn 2009)
ASTM E 207 : 2008 Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison with a Reference Thermoelement of Similar EMF-Temperature Properties
ASTM E 2714 : 2013 : REDLINE Standard Test Method for Creep-Fatigue Testing
EN ISO 10426-1:2009/AC:2018 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION - TECHNICAL CORRIGENDUM 2 (ISO 10426-1:2009/COR 2:2012)
ASTM C 965 : 1996 : R2002 Standard Practice for Measuring Viscosity of Glass Above the Softening Point
ASTM C 767 : 1993 : R1998 Standard Test Method for Thermal Conductivity of Carbon Refractories
ASTM C 372 : 1994 : R2012 Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
ISO 17245:2015 Corrosion of metals and alloys Test method for high temperature corrosion testing of metallic materials by immersing in molten salt or other liquids under static conditions
ASTM C 16 : 2003 : R2008 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
ASTM D 4421 : 1994 : R1999 Standard Test Method for Volatile Matter in Petroleum Coke (Withdrawn 2004)
ASTM E 2820 : 2013-07 TEST METHOD FOR EVALUATING THERMAL EMF PROPERTIES OF BASE-METAL THERMOCOUPLE CONNECTORS
ASTM E 696 : 2007 : R2013 Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire
ASTM C 1862 : 2017 Standard Test Method for the Nominal Joint Strength of End-Plug Joints in Advanced Ceramic Tubes at Ambient and Elevated Temperatures
ASTM D 5110 : 1998 : R2010 Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry
ASTM E 2730 : 2010 : R2015 : EDT 1 Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits
ASTM C 417 : 2005 : R2015 Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories
ASTM D 5249 : 2010 : R2016 Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints
ASTM E 2368 : 2010 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
ISO 14428:2005 Carbonaceous materials for the production of aluminium Cold and tepid ramming pastes Expansion/shrinkage during baking
ASTM D 345 : 2002 Side bearings of the freight wagon bogies. General specifications
ISO 10426-6:2008 Petroleum and natural gas industries — Cements and materials for well cementing — Part 6: Methods for determining the static gel strength of cement formulations
ASTM D 3466 : 2006 : R2011 Standard Test Method for Ignition Temperature of Granular Activated Carbon
ASTM F 689 : 1997 Standard Practice for Determination of the Temperature of Above-Ground Plastic Gas Pressure Pipe Within Metallic Casings
ASTM C 1276 : 1994 : R1999 Standard Test Method for Measuring the Viscosity of Mold Powders Above Their Melting Point Using a Rotational Viscometer
ISO 10426-1:2009 Petroleum and natural gas industries Cements and materials for well cementing Part 1: Specification
I.S. EN ISO 10426-6:2008 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 6: METHODS FOR DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATIONS
03/301334 DC : DRAFT JAN 2003 ISO 15379-1 - CARBONACEOUS MATERIALS FOR THE PRODUCTION OF ALUMINIUM - CATHODE BLOCKS - PART 1: DETERMINATION OF THE EXPANSION DUE TO SODIUM PENETRATION WITH APPLICATION OF PRESSURE
ASTM C 1465 : 2008 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress-Rate Flexural Testing at Elevated Temperatures
SAE ARP 5144 : 2017 HEAT APPLICATION FOR THERMOSETTING RESIN CURING
ASTM D 5110 : 1998 : R2004 Standard Practice for Calibration of Ozone Monitors and Certification of Ozone Transfer Standards Using Ultraviolet Photometry
13/30259880 DC : 0 BS ISO 17224 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR HIGH-TEMPERATURE CORROSION TESTING OF METALLIC MATERIALS BY APPLICATION OF A DEPOSIT OF SALT, ASH OR OTHER SUBSTANCES
BS ISO 17224:2015 Corrosion of metals and alloys. Test method for high temperature corrosion testing of metallic materials by application of a deposit of salt, ash, or other substances
BS EN ISO 10426-6:2008 Petroleum and natural gas industries. Cements and materials for well cementing Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)
API MPM CH19.3C : 1998 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - EVAPORATIVE LOSS MEASUREMENT - WEIGHT LOSS TEST METHOD FOR THE MEASUREMENT OF RIM-SEAL LOSS FACTORS FOR INTERNAL FLOATING-ROOF TANKS
ASTM D 6200 : 2001 : R2012 Standard Test Method for Determination of Cooling Characteristics of Quench Oils by Cooling Curve Analysis
ASTM E 289 : 2017 : REDLINE Standard Test Method for Linear Thermal Expansion of Rigid Solids with Interferometry
ISO 21608:2012 Corrosion of metals and alloys — Test method for isothermal-exposure oxidation testing under high-temperature corrosion conditions for metallic materials
ASTM D 6549 : 2006 : R2011 Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit)
ASTM C 767 : 1993 : R2009 Standard Test Method for Thermal Conductivity of Carbon Refractories
ASTM E 608/E608M : 2013 : REDLINE SPECIFICATION FOR MINERAL-INSULATED, METAL-SHEATHED BASE METAL THERMOCOUPLES
ASTM D 1676 : 2017 : REDLINE Standard Test Methods for Film-Insulated Magnet Wire
ASTM D 5249 : 2010 Standard Specification for Backer Material for Use with Cold- and Hot-Applied Joint Sealants in Portland-Cement Concrete and Asphalt Joints
ASTM F 2082/F2082M : 2016 : REDLINE Standard Test Method for Determination of Transformation Temperature of Nickel-Titanium Shape Memory Alloys by Bend and Free Recovery
AASHTO T 240 : 2013 METHOD OF TEST FOR EFFECT OF HEAT AND AIR ON A MOVING FILM OF ASPHALT BINDER (ROLLING THIN-FILM OVEN TEST)
ASTM C 1337 : 2017 : REDLINE Standard Test Method for Creep and Creep Rupture of Continuous Fiber-Reinforced Advanced Ceramics Under Tensile Loading at Elevated Temperatures
ASTM E 1530 : 2011 Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
API 10A CHINESE : 2002 SPECIFICATION FOR CEMENTS AND MATERIALS FOR WELL CEMENTING
AASHTO T 48 : 2006 : R2015 METHOD OF TEST FOR FLASH AND FIRE POINTS BY CLEVELAND OPEN CUP
ASTM C 182 : 1988 : R2013 Standard Test Method for Thermal Conductivity of Insulating Firebrick
ASTM D 6374 : 2012 : R2017 : EDT 1 Standard Test Method for Volatile Matter in Green Petroleum Coke Quartz Crucible Procedure
ASTM C 965 : 1996 Standard Practice for Measuring Viscosity of Glass Above the Softening Point
AASHTO T 313 : 2012 METHOD OF TEST FOR DETERMINING THE FLEXURAL CREEP STIFFNESS OF ASPHALT BINDER USING THE BENDING BEAM RHEOMETER (BBR)
ASTM D 6482 : 2006 : R2016 Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method)
AASHTO T 78 : 2015 METHOD OF TEST FOR DISTILLATION OF CUTBACK ASPHALT PRODUCTS
ASTM D 6549 : 2006 : R2015 Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit)
ASTM D 6482 : 2006 : R2011 Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants by Cooling Curve Analysis with Agitation (Tensi Method)
ASTM C 965 : 1996 : R2017 Standard Practice for Measuring Viscosity of Glass Above the Softening Point
ASTM C 1366 : 2004 : R2013 Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures
ASTM D 5207 : 2014 : REDLINE Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials
ASTM E 2846 : 2014-10 GUIDE FOR THERMOCOUPLE VERIFICATION
ASTM D 447 : 1993 Test Method for Distillation of Plant Spray Oils (Withdrawn 1997)
ASTM D 243/D243M : 2014 : REDLINE Standard Test Method for Residue of Specified Penetration
UNI EN ISO 10426-2 : 2006 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 2: TESTING OF WELL CEMENTS
UNI EN ISO 10426-1 : 2010 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 1: SPECIFICATION
ASTM C 201 : 1993 : R2004 Standard Test Method for Thermal Conductivity of Refractories
ASTM G 179 : 2004 Standard Specification for Metal Black Panel and White Panel Temperature Devices for Natural Weathering Tests
ASTM D 3026 : 1994 Standard Test Method for Sinter Index of Electrical Grade Magnesium Oxide for Use in Sheathed Heating Elements (Withdrawn 2002)
10/30217198 DC : 0 BS EN ISO 10426-2 - PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 2: TESTING OF WELL CEMENTS
ASTM E 235/E235M : 2012 Standard Specification for Type K and Type N Mineral-Insulated, Metal-Sheathed Thermocouples for Nuclear or for Other High-Reliability Applications
CSA A23.1 A23.2 : 2014 CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE
API MPM CH19.3A : 1997(R2012) MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART A - WIND TUNNEL TEST METHOD FOR THE MEASUREMENT OF DECK-FITTING LOSS FACTORS FOR EXTERNAL FLOATING-ROOF TANKS
ASTM C 16 : 2003 : R2012 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
10/30231379 DC : 0 BS ISO 21608 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR ISOTHERMAL-EXPOSURE OXIDATION TESTING UNDER HIGH-TEMPERATURE CORROSION CONDITIONS FOR METALLIC MATERIALS
ASTM D 3466 : 2006 Standard Test Method for Ignition Temperature of Granular Activated Carbon
MIL-DTL-25446 Revision E:2012 Transmitter, Temperature, Electrical Resistance, Armored, Bayonet Locking Type, (-50 Degrees C to 300 Degrees C)
ASTM E 633 : 2013 : REDLINE Standard Guide for Use of Thermocouples in Creep and Stress-Rupture Testing to 1800°F (1000°C) in Air
ISO 15379-1:2015 Carbonaceous materials for the production of aluminium Cathode block materials Part 1: Determination of the expansion due to sodium penetration with application of pressure
ASTM E 2730 : 2010 Standard Practice for Calibration and Use of Thermocouple Reference Junction Probes in Evaluation of Electronic Reference Junction Compensation Circuits
ASTM C 16 : 2003 : R2008 : EDT 1 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
BS ISO 14428:2004 Carbonaceous materials for the production of aluminium. Cold and tepid ramming pastes. Expansion/shrinkage during baking
BS ISO 15379-1:2015 Carbonaceous materials for the production of aluminium. Cathode block materials Determination of the expansion due to sodium penetration with application of pressure
AASHTO TP 85 : 2010 : R2013 METHOD OF TEST FOR APPARENT VISCOSITY OF HOT-POURED BITUMINOUS CRACK SEALANT USING BROOKFIELD ROTATIONAL VISCOMETER RV SERIES INSTRUMENT
ASTM E 696 : 2007 : R2018 Standard Specification for Tungsten-Rhenium Alloy Thermocouple Wire
ASTM C 182 : 1988 : R2004 Standard Test Method for Thermal Conductivity of Insulating Firebrick
TR AMS2750 : 2009 AEROSPACE SERIES - AEROSPACE MATERIAL SPECIFICATION - PYROMETRY
AASHTO TP 85 : 2010 : R2015 METHOD OF TEST FOR APPARENT VISCOSITY OF HOT-POURED BITUMINOUS CRACK SEALANT USING BROOKFIELD ROTATIONAL VISCOMETER RV SERIES INSTRUMENT
ASTM C 182 : 1988 : R2009 Standard Test Method for Thermal Conductivity of Insulating Firebrick
AASHTO TP 90 : 2010 : R2015 METHOD OF TEST FOR MEASURING INTERFACIAL FRACTURE ENERGY OF HOT-POURED CRACK SEALANT USING A BLISTER TEST
API 10B-6 : 2010 : R2015 RECOMMENDED PRACTICE ON DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATIONS
ASTM C 417 :2005 Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories
BS EN ISO 10426-1:2009 Petroleum and natural gas industries. Cements and materials for well cementing Specification
ASTM E 601 : 2015 : REDLINE Standard Guide for Measuring Electromotive Force (emf) Stability of Base-Metal Thermoelement Materials with Time in Air
ASTM C 372 : 1994 : R2001 : EDT 1 Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
ASTM C 1099 : 2007 : R2012 Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
ASTM C 201 : 1993 : R2019 Standard Test Method for Thermal Conductivity of Refractories
ASTM C 1099 : 2007 Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
ASTM C 202 : 1993 : R2009 : EDT 1 Standard Test Method for Thermal Conductivity of Refractory Brick
ASTM C 417 : 2005 : R2010 : EDT 1 Standard Test Method for Thermal Conductivity of Unfired Monolithic Refractories
ASTM D 402/D402M : 2014 : REDLINE Standard Test Method for Distillation of Cutback Asphalt (Withdrawn 2023)
ASTM E 2760 : 2016 : REDLINE Standard Test Method for Creep-Fatigue Crack Growth Testing
ASTM E 1232 : 2007 : R2013 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM C 1291 : 2018 : REDLINE Standard Test Method for Elevated Temperature Tensile Creep Strain, Creep Strain Rate, and Creep Time to Failure for Monolithic Advanced Ceramics
ASTM D 7646 : 2010 : R2014 Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants for Aluminum Alloys by Cooling Curve Analysis
ASTM E 1232 : 2007 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM E 1333 : 2014 : REDLINE Standard Test Method for Determining Formaldehyde Concentrations in Air and Emission Rates from Wood Products Using a Large Chamber
ISO 20202:2004 Carbonaceous materials used in the production of aluminium — Cold and tepid ramming pastes — Preparation of baked test pieces and determination of loss on baking
ISO 10426-2:2003 Petroleum and natural gas industries — Cements and materials for well cementing — Part 2: Testing of well cements
EN ISO 10426-6:2008 Petroleum and natural gas industries - Cements and materials for well cementing - Part 6: Methods for determining the static gel strength of cement formulations (ISO 10426-6:2008)
ASTM E 608/E608M : 2013 : R2019 Standard Specification for Mineral-Insulated, Metal-Sheathed Base Metal Thermocouples
ASTM C 24 : 2009 Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High Alumina Refractory Materials
BS ISO 17245:2015 Corrosion of metals and alloys. Test method for high temperature corrosion testing of metallic materials by immersing in molten salt or other liquids under static conditions
ISO 13573:2012 Corrosion of metals and alloys — Test method for thermal-cycling exposure testing under high-temperature corrosion conditions for metallic materials
ASTM C 372 : 1994 : R2016 Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
ASTM C 372 : 1994 Standard Test Method for Linear Thermal Expansion of Porcelain Enamel and Glaze Frits and Fired Ceramic Whiteware Products by the Dilatometer Method
11/30210857 DC : 0 BS ISO 13573 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR THERMAL-CYCLING EXPOSURE TESTING UNDER HIGH-TEMPERATURE CORROSION CONDITIONS FOR METALLIC MATERIALS
13/30259830 DC : 0 BS ISO 17248 - CORROSION OF METALS AND ALLOYS - TEST METHOD FOR HIGH-TEMPERATURE CORROSION TESTING OF METALLIC MATERIALS BY EMBEDDING IN SALT, ASH, OR OTHER SOLIDS
BS ISO 20202:2004 Carbonaceous materials used in the production of aluminium. Cold and tepid ramming pastes. Preparation of baked test pieces and determination of loss on baking
ASTM D 6084/D6084M : 2013-12 TEST METHOD FOR ELASTIC RECOVERY OF ASPHALT MATERIALS BY DUCTILOMETER
ASTM C 201 : 1993 : R1998 Standard Test Method for Thermal Conductivity of Refractories
ASTM C 38 : 1989 Method for Panel Spalling Testing Refractory Brick (Withdrawn 1994)
ASTM C 16 : 2003 : R2012 : EDT 1 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
MIL-P-11570 Revision C:1984 PYROMETERS, INDICATING, THERMOCOUPLES
AASHTO R 28 : 2012 PRACTICE FOR ACCELERATED AGING OF ASPHALT BINDER USING A PRESSURIZED AGING VESSEL (PAV)
ASTM C 621 : 2009 : R2014 Standard Test Method for Isothermal Corrosion Resistance of Refractories to Molten Glass
ASTM G 179 : 2004 : R2011 Standard Specification for Metal Black Panel and White Panel Temperature Devices for Natural Weathering Tests
ASTM C 201 : 1993 : R2009 Standard Test Method for Thermal Conductivity of Refractories
SAE AS 7101 : 2007 NATIONAL AEROSPACE AND DEFENSE CONTRACTORS ACCREDITATION PROGRAM (NADCAP) GENERAL REQUIREMENTS FOR MATERIALS TEST LABORATORY ACCREDITATION PROGRAM
AASHTO TP 89 : 2010 : R2013 METHOD OF TEST FOR MEASURING ADHESION OF HOT-POURED CRACK SEALANT USING DIRECT ADHESION TESTER
AASHTO TP 89 : 2010 : R2015 METHOD OF TEST FOR MEASURING ADHESION OF HOT-POURED CRACK SEALANT USING DIRECT ADHESION TESTER
SAE AMS 2750 : 2012 PYROMETRY
ASTM E 2368 : 2010 : R2017 Standard Practice for Strain Controlled Thermomechanical Fatigue Testing
API MPM CH19.3A : 1997 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART A - WIND TUNNEL TEST METHOD FOR THE MEASUREMENT OF DECK-FITTING LOSS FACTORS FOR EXTERNAL FLOATING-ROOF TANKS
ASTM E 2181/E2181M : 2011 Standard Specification for Compacted Mineral-Insulated, Metal-Sheathed, Noble Metal Thermocouples and Thermocouple Cable
ASTM D 6549 : 2006 Standard Test Method for Determination of Cooling Characteristics of Quenchants by Cooling Curve Analysis with Agitation (Drayton Unit)
API MPM CH19.3A : 1997 : R2007 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 19.3 - EVAPORATIVE LOSS MEASUREMENT - PART A - WIND TUNNEL TEST METHOD FOR THE MEASUREMENT OF DECK-FITTING LOSS FACTORS FOR EXTERNAL FLOATING-ROOF TANKS
UNI EN ISO 10426-6 : 2009 PETROLEUM AND NATURAL GAS INDUSTRIES - CEMENTS AND MATERIALS FOR WELL CEMENTING - PART 6: METHODS FOR DETERMINING THE STATIC GEL STRENGTH OF CEMENT FORMULATION
ASTM E 2584 : 2014 : REDLINE Standard Practice for Thermal Conductivity of Materials Using a Thermal Capacitance (Slug) Calorimeter
ASTM D 4693 : 2007 : R2012 Standard Test Method for Low-Temperature Torque of Grease-Lubricated Wheel Bearings
ASTM C 182 : 1988 : R1998 Standard Test Method for Thermal Conductivity of Insulating Firebrick
ASTM C 965 : 1996 : R2007 Standard Practice for Measuring Viscosity of Glass Above the Softening Point
ASTM C 24 : 2009 : R2018 Standard Test Method for Pyrometric Cone Equivalent (PCE) of Fireclay and High-Alumina Refractory Materials
ASTM C 16 : 2003 : R2018 Standard Test Method for Load Testing Refractory Shapes at High Temperatures
ASTM C 583 : 2015 : REDLINE Standard Test Method for Modulus of Rupture of Refractory Materials at Elevated Temperatures
ASTM C 1834 : 2016 Standard Test Method for Determination of Slow Crack Growth Parameters of Advanced Ceramics by Constant Stress Flexural Testing (Stress Rupture) at Elevated Temperatures
ASTM C 767 : 1993 : R2004 Standard Test Method for Thermal Conductivity of Carbon Refractories
ISO 17248:2015 Corrosion of metals and alloys Test method for high temperature corrosion testing of metallic materials by embedding in salt, ash, or other solids
ASTM D 6723 : 2012 Standard Test Method for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) (Withdrawn 2021)
ASTM C 1099 : 2007 : R2019 Standard Test Method for Modulus of Rupture of Carbon-Containing Refractory Materials at Elevated Temperatures
ASTM D 113 : 2017 Standard Test Method for Ductility of Asphalt Materials
ASTM E 1232 : 2007 : R2019 Standard Test Method for Temperature Limit of Flammability of Chemicals
ASTM E 1530 : 2011 : R2016 Standard Test Method for Evaluating the Resistance to Thermal Transmission of Materials by the Guarded Heat Flow Meter Technique
ASTM E 839 : 2011 : R2016 : EDT 1 Standard Test Methods for Sheathed Thermocouples and Sheathed Thermocouple Cable
ASTM E 344 : 2016-12 TERMINOLOGY RELATING TO THERMOMETRY AND HYDROMETRY
ASTM C 1366 : 2004 Standard Test Method for Tensile Strength of Monolithic Advanced Ceramics at Elevated Temperatures
ASTM E 207 : 2008 : R2015 Standard Test Method for Thermal EMF Test of Single Thermoelement Materials by Comparison with a Reference Thermoelement of Similar EMF-Temperature Properties
EN ISO 10426-2:2003/AC:2007 Petroleum and natural gas industries - Cements and materials for well cementing - Part 2: Testing of well cements (ISO 10426-2:2003/Cor 1:2006)

ASTM E 230 : 2003 Standard Specification and Temperature-Electromotive Force (EMF) Tables for Standardized Thermocouples
ASTM E 1 : 2014 : REDLINE Standard Specification for ASTM Liquid-in-Glass Thermometers
ASTM E 2846 : 2014-10 GUIDE FOR THERMOCOUPLE VERIFICATION
ASTM E 1594 : 2016 : REDLINE Standard Guide for Expression of Temperature
ASTM E 644 : 2011 : REDLINE Standard Test Methods for Testing Industrial Resistance Thermometers
ASTM E 344 : 2016-12 TERMINOLOGY RELATING TO THERMOMETRY AND HYDROMETRY
ASTM E 1751 : 2000 Standard Guide for Temperature Electromotive Force (emf) Tables for Non-Letter Designated Thermocouple Combinations (Withdrawn 2009)

View more information
£70.87
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.