• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 2593 : 2017

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Accuracy Verification of Industrial Platinum Resistance Thermometers
Available format(s)

Hardcopy , PDF

Superseded date

14-07-2023

Language(s)

English

Published date

01-12-2017

This guide describes the techniques and apparatus required for the accuracy verification of industrial platinum resistance thermometers constructed in accordance with Specification E1137/E1137M and the evaluation of calibration uncertainties.

1.1This guide describes the techniques and apparatus required for the accuracy verification of industrial platinum resistance thermometers constructed in accordance with Specification E1137/E1137M and the evaluation of calibration uncertainties. The procedures described apply over the range of -200 °C to 650 °C.

1.2This guide does not intend to describe procedures necessary for the calibration of platinum resistance thermometers used as calibration standards or Standard Platinum Resistance Thermometers. Consequently, calibration of these types of instruments is outside the scope of this guide.

1.3Industrial platinum resistance thermometers are available in many styles and configurations. This guide does not purport to determine the suitability of any particular design, style, or configuration for calibration over a desired temperature range.

1.4The evaluation of uncertainties is based upon current international practices as described in JCGM 100:2008 “Evaluation of measurement data—Guide to the expression of uncertainty in measurement” and ANSI/NCSL Z540.2-1997 “U.S. Guide to the Expression of Uncertainty in Measurement.”

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
E 20
DocumentType
Guide
Pages
15
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2162 : 2021 Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards
ASTM D 2532 : 2022 Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants
ASTM D 445 : 2021 : EDT 2 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)
ASTM D 2162 : 2017 Standard Practice for Basic Calibration of Master Viscometers and Viscosity Oil Standards
ASTM D 2532 : 2017 Standard Test Method for Viscosity and Viscosity Change After Standing at Low Temperature of Aircraft Turbine Lubricants
ASTM E 2877 : 2012 : R2019 Standard Guide for Digital Contact Thermometers
ASTM D 445 : 2019 Standard Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

ASTM E 563 : 1997 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM E 1750 : 1995 Standard Guide for Use of Water Triple Point Cells
ASTM E 2488 : 2009 Standard Guide for the Preparation and Evaluation of Liquid Baths Used for Temperature Calibration by Comparison
ASTM E 344 : 2018 Terminology Relating to Thermometry and Hydrometry
ASTM E 2488 : 2009 : R2014 Standard Guide for the Preparation and Evaluation of Liquid Baths Used for Temperature Calibration by Comparison
ASTM E 1502 : 2022 Standard Guide for Use of Fixed-Point Cells for Reference Temperatures
ASTM E 344 : 2001 : REV A Terminology Relating to Thermometry and Hydrometry
ASTM E 1750 : 2009 Standard Guide for Use of Water Triple Point Cells
ASTM E 1502 : 2010 Standard Guide for Use of Fixed-Point Cells for Reference Temperatures
ASTM E 2623 : 2014 : R2021 Standard Practice for Reporting Thermometer Calibrations
ASTM E 1750 : 2002 Standard Guide for Use of Water Triple Point Cells
ASTM E 1502 : 2016 Standard Guide for Use of Fixed-Point Cells for Reference Temperatures
ASTM E 563 : 2022 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM E 563 : 2011 : R2016 Standard Practice for Preparation and Use of an Ice-Point Bath as a Reference Temperature
ASTM E 2623 : 2014 Standard Practice for Reporting Thermometer Calibrations
ASTM E 2623 : 2008 Standard Practice for Reporting Temperature Calibrations
ASTM E 1502 : 1998 Standard Guide for Use of Freezing-Point Cells for Reference Temperatures
ASTM E 2623 : 2008 : EDT 1 Standard Practice for Reporting Thermometer Calibrations
ASTM E 1750 : 2010 Standard Guide for Use of Water Triple Point Cells
ASTM E 2488 : 2022 Standard Guide for the Preparation and Evaluation of Liquid Baths Used for Temperature Calibration by Comparison
ASTM E 1750 : 2010 : R2016 Standard Guide for Use of Water Triple Point Cells

View more information
£69.29
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.