• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ASTM E 2707 : 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure
Available format(s)

Hardcopy , PDF

Superseded date

17-06-2022

Language(s)

English

Published date

10-11-2015

1.1This fire-test-response standard prescribes a method to assess the fire performance of a vertically oriented specimen exposed to direct flame impingement in a simulated external fire exposure potentially encountered in a ‘Wildland Urban Interface’ scenario. This test method provides data suitable for comparing the performance of materials, which are used as the exposed surfaces of exterior walls in construction applications.

Note 1:This test method closely follows the test procedure of California Office of State Marshal (SFM) Method 12-7A-1.2

1.2This test method measures the ability of the wall system to resist fire penetration from the exterior into the wall cavity or unexposed side of the test assembly under the conditions of exposure.

1.3This test method provides data suitable for comparing the performance of vertically oriented materials, products or assemblies in exterior construction applications. The test specimen shall be tested in thicknesses and configurations representative of actual end product or system uses.

1.4Limitations of the test method are listed in Section 5.5.

1.5The system of units to be used in referee decisions is the SI system of units; see IEEE/ASTM SI-10 for further details. The units given in parentheses are for information only.

1.6This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.7This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.8Fire testing is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.

Committee
E 05
DocumentType
Test Method
Pages
8
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM E 2957 : 2017 Standard Test Method for Resistance to Wildfire Penetration of Eaves, Soffits and Other Projections
ASTM E 2886/E2886M : 2014 Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingement
ASTM E 176 : 2018 : REV A Standard Terminology of Fire Standards
ASTM E 176 : 2021 : REV A Standard Terminology of Fire Standards

ASTM E 1474 : 1996 : REV A Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM D 6662 : 2022 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards
ASTM E 1354 : 2010 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 6662 : 2017 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards
ASTM D 6662 : 2007 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards
ASTM D 2898 : 2008 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM E 1740 : 2009 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter
ASTM E 1354 : 2002 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2014 : EDT 1 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 7032 : 2010 : REV A Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM D 7032 : 2004 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM D 4444 : 1992 : R1998 : EDT 1 Standard Test Methods for Use and Calibration of Hand-Held Moisture Meters
ASTM D 4442 : 2007 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM E 1474 : 2014 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM D 7032 : 2015 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails
ASTM D 2898 : 1994 : R1999 Standard Test Methods for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM E 2257 : 2013 : REV A Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM E 1740 : 2020 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
ASTM E 1354 : 2004 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 1999 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1474 : 2001 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 1354 : 2010 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1474 : 2020 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM D 7032 : 2007 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM E 1474 : 2004 : EDT 1 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 1740 : 2001 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter
ASTM E 1354 : 2003 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2002 : REV D : EDT 1 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 4442 : 2015 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM E 2102 : 2011 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM D 7032 : 2014 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM E 1474 : 2002 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM D 4444 : 2008 Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
ASTM E 1354 : 2008 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 176 : 2018 : REV A : EDT 1 Standard Terminology of Fire Standards
ASTM E 1354 : 2002 : REV D Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1474 : 2007 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 1740 : 2022 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
ASTM E 2257 : 2016 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM D 4444 : 1992 : R2003 Standard Test Methods for Use and Calibration of Hand-Held Moisture Meters
ASTM D 4444 : 2013 Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
ASTM D 4442 : 2016 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D 4444 : 2013 : R2018 Standard Test Method for Laboratory Standardization and Calibration of Hand-Held Moisture Meters
ASTM E 1354 : 2009 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 2257 : 2013 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM E 2257 : 2008 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM E 1474 : 2004 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 2102 : 2013 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM E 1474 : 2021 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 1354 : 2015 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 6662 : 2009 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards
ASTM D 6662 : 2001 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards
ASTM E 1354 : 2016 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 176 : 2021 Standard Terminology of Fire Standards
ASTM D 7032 : 2005 : REV A Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM D 6662 : 2013 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards
ASTM E 1740 : 2015 Standard Test Method for Determining the Heat Release Rate and Other<brk/> Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
ASTM E 1740 : 2002 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter
ASTM E 1740 : 2000 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter
ASTM E 2102 : 2015 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM D 4442 : 2020 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials
ASTM D 2898 : 2007 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM E 176 : 2018 : REV A : EDT 2 Standard Terminology of Fire Standards
ASTM D 7032 : 2010 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM E 1354 : 2016 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1474 : 2020 : REV A Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 2257 : 2017 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM D 2898 : 1994 : R2004 Standard Test Methods for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM D 7032 : 2017 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails
ASTM E 1354 : 2017 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 2102 : 2008 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM E 1740 : 2007 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter
ASTM E 2102 : 2011 : REV A Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM E 1740 : 2010 Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
ASTM E 1354 : 2002 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 2257 : 2003 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM E 1740 : 2020 : REV A Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter
ASTM D 2898 : 1977 Standard Methods for Accelerated Weathering Of Fire-Retardant-Treated Wood For Fire Testing
ASTM E 1354 : 2015 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 2102 : 2014 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM D 2898 : 2009 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM E 1740 : 2007 : REV A Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wallcovering Composites Using a Cone Calorimeter
ASTM E 1354 : 2011 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 2102 : 2004 : REV A Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM E 1354 : 2011 : REV B Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1474 : 2022 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM E 1354 : 2011 : REV A Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 7032 : 2006 : REV A Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM E 2257 : 2022 Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies
ASTM D 7032 : 2005 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM D 7032 : 2021 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails
ASTM D 7032 : 2008 Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails)
ASTM E 2102 : 2021 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM D 2898 : 2010 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM E 1474 : 2010 Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter
ASTM D 2898 : 2010 : R2017 Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
ASTM E 2102 : 2000 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM E 176 : 2021 : REV A Standard Terminology of Fire Standards
ASTM E 2102 : 2004 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM D 4442 : 1992 : R1997 : EDT 1 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM E 1354 : 2004 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2013 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM E 1354 : 2014 Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter
ASTM D 4442 : 1984 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM E 2102 : 2009 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM E 2102 : 2017 Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater
ASTM D 4442 : 1992 : R2003 Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Base Materials
ASTM D 6662 : 2006 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards

View more information
£62.61
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.