ASTM E 2726/E2726M : 2012 : REV A : R2017
Current
The latest, up-to-date edition.
Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands
Hardcopy , PDF
English
15-12-2017
CONTAINED IN VOL. 04.07, 2017 Describes the fire-test-response characteristics of deck structures attached to or in close proximity to primary structures.
Committee |
E 05
|
DocumentType |
Test Method
|
Pages |
7
|
ProductNote |
Reconfirmed 2017
|
PublisherName |
American Society for Testing and Materials
|
Status |
Current
|
Supersedes |
1.1This test method determines the fire-test-response characteristics of deck structures attached to or in close proximity to primary structures. The burning brand exposures test is intended to determine the degradation modes of decking materials when exposed to a burning brand on the upper surface of a deck structure.
1.2The use of paints, coatings, stains, or other surface treatments for fire protection purposes are beyond the scope of this test method. This test method excludes the use of paints, stains, or coatings for this fire-test-response determination.
1.3The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.
1.5Fire testing of products and materials is inherently hazardous. Adequate safeguards for personnel and property shall be employed in conducting these tests.
1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D 6662 : 2022 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 6662 : 2017 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 6662 : 2007 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 2898 : 2008 | Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM E 84 : 2023 : REV D | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 7032 : 2010 : REV A | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM D 7032 : 2004 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM E 84 : 2023 : REV C | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 7032 : 2015 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM D 2898 : 1994 : R1999 | Standard Test Methods for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM D 6662 : 2017 : REDLINE | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 7032 : 2007 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM E 176 : 2021 : REV A : EDT 1 | Standard Terminology of Fire Standards |
ASTM D 7032 : 2014 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 176 : 2018 : REV A : EDT 1 | Standard Terminology of Fire Standards |
ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 108 : 2017 : REDLINE | Standard Test Methods for Fire Tests of Roof Coverings |
ASTM E 176 : 2024 | Standard Terminology of Fire Standards |
ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2024 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 6662 : 2009 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 6662 : 2001 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM E 176 : 2021 | Standard Terminology of Fire Standards |
ASTM D 7032 : 2005 : REV A | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM D 6662 : 2013 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
ASTM D 7032 : 2017 : REDLINE | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM D 2898 : 2007 | Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM E 176 : 2018 : REV A : EDT 2 | Standard Terminology of Fire Standards |
ASTM D 7032 : 2010 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM D 2898 : 1994 : R2004 | Standard Test Methods for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM D 7032 : 2017 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM D 2898 : 2010 : R2024 | Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM D 2898 : 1977 | Standard Methods for Accelerated Weathering Of Fire-Retardant-Treated Wood For Fire Testing |
ASTM D 2898 : 2009 | Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM E 84 : 2023 : REV B | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 7032 : 2006 : REV A | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM D 7032 : 2005 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM D 7032 : 2021 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
ASTM D 7032 : 2008 | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite Deck Boards and Guardrail Systems (Guards or Handrails) |
ASTM E 84 : 2023 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
ASTM D 2898 : 2010 | Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM D 2898 : 2010 : R2017 | Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing |
ASTM E 176 : 2021 : REV A | Standard Terminology of Fire Standards |
ASTM D 6662 : 2006 | Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards |
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.