AWWA C541 : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
HYDRAULIC AND PNEUMATIC CYLINDER AND VANE-TYPE ACTUATORS FOR VALVES AND SLIDE GATES
Hardcopy , PDF
English
01-09-2016
25-02-2022
Foreword
I Introduction
II Special Issues
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendixes
A Pneumatic or Hydraulic Actuator
Data Form
B Driver Media
Specifies hydraulic and pneumatic linear and quarter-turn actuators for operation of valves and slide gates in utility systems.
| DevelopmentNote |
Supersedes AWWA C540. (11/2009)
|
| DocumentType |
Standard
|
| ISBN |
9781625761439
|
| Pages |
48
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| AWWA C507 : 2015 | BALL VALVES, 6 IN. THROUGH 60 IN. (150 MM THROUGH 1,500 MM) |
| ANSI/AWWA C561 : 2014 | FABRICATED STAINLESS-STEEL SLIDE GATES |
| AWWA C504 : 2015 | RUBBER-SEATED BUTTERFLY VALVES |
| AWWA C516 : 2014 | LARGE-DIAMETER RUBBER-SEATED BUTTERFLY VALVES, SIZES 78 IN. (2,000 MM) AND LARGER |
| AWWA M49 : 2017 | BUTTERFLY VALVES: TORQUE, HEAD LOSS, AND CAVITATION ANALYSIS |
| AWWA C562 : 2014 | FABRICATED ALUMINUM SLIDE GATES |
| AWWA C520 : 2014 | KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM) |
| AWWA C560:2014 | CAST-IRON SLIDE GATES |
| AWWA C563 : 2014 | FABRICATED COMPOSITE SLIDE GATES |
| AWWA C517 : 2016 | RESILIENT-SEATED CAST-IRON ECCENTRIC PLUG VALVES |
| ANSI/AWWA C522:2022 | Rotary Cone Valves, 6 In. Through 60 In. (150 mm Through 1,500 mm) |
| NFPA T3.6.8 : 2010 | FLUID POWER SYSTEMS - CYLINDERS - DIMENSIONS FOR ACCESSORIES FOR CATALOGED SQUARE HEAD INDUSTRIAL TYPES |
| ASTM B 733 : 2015 : REDLINE | Standard Specification for Autocatalytic (Electroless) Nickel-Phosphorus Coatings on Metal |
| ASTM B 154 : 2016 : REDLINE | Standard Test Method for Mercurous Nitrate Test for Copper Alloys |
| ASTM A 395/A395M : 1999 | Standard Specification for Ferritic Ductile Iron Pressure-Retaining Castings for Use at Elevated Temperatures |
| ASTM A 689 : 1997 : R2002 | Standard Specification for Carbon and Alloy Steel Bars for Springs |
| SAE J429_201405 | Mechanical and Material Requirements for Externally Threaded Fasteners |
| ASTM A 516/A516M : 2017 : REDLINE | Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service |
| ASTM B 240 : 2017 : REDLINE | Standard Specification for Zinc and Zinc-Aluminum (ZA) Alloys in Ingot Form for Foundry and Die Castings |
| ASTM A 449 : 2014 : REDLINE | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use |
| ASTM A 276/A276M : 2017 : REDLINE | Standard Specification for Stainless Steel Bars and Shapes |
| ASTM D 570 : 1998 : R2018 | Standard Test Method for Water Absorption of Plastics |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.