AWWA C606 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
GROOVED AND SHOULDERED JOINTS
Hardcopy , PDF
English
01-06-2015
07-04-2023
Foreword
I Introduction
II Special ISSUES
III Use of This Standard
IV Major Revisions
V Comments
Standard
1 General
2 References
3 Definitions
4 Requirements
5 Verification
6 Delivery
Appendix
A - Guidelines for Grooved and
Shouldered Piping Spacing,
Support, Anchorage, and
Guidance
Specifies grooved and shouldered joints for ductile-iron pipe, metallic pressure pipe of iron pipe size (IPS), fittings, and other components for water service. The standard describes 4-in. through 36-in. (100-mm through 900-mm) diameter grooved ductile-iron pipe; ?-in. through 24-in. (19-mm through 600-mm) diameter grooved steel, aluminum, brass, and other metallic pipe of IPS dimensions; and 4-in. through 64-in. (100-mm through 1,600-mm) nominal diameter shouldered ends for ductile-iron pipe and metallic pipe of IPS dimensions.
| DocumentType |
Revision
|
| ISBN |
9781625760982
|
| Pages |
40
|
| PublisherName |
American Water Works Association
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| FM 1020 : 2007 | AUTOMATIC WATER CONTROL VALVES |
| FM 1610 : 2016 | DUCTILE IRON PIPE AND FITTINGS, FLEXIBLE FITTINGS AND COUPLINGS |
| AWWA C226 : 2013 | STAINLESS-STEEL FITTINGS FOR WATERWORKS SERVICE, SIZES 1/2 IN. THROUGH 72 IN. (13 MM THROUGH 1,800 MM) |
| ASTM A 377 : 2003 | Standard Index of Specifications for Ductile-Iron Pressure Pipe |
| MSS SP 145 : 2013 | METAL BALL VALVES FOR LOW PRESSURE/LOW TEMPERATURE PLUMBING APPLICATIONS |
| ASTM A 377 : 2003 : R2008 : EDT 1 | Standard Index of Specifications for Ductile-Iron Pressure Pipe |
| FM 1421 : 2007 | MONITOR ASSEMBLY |
| ASTM F 1476 : 2007 | Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications |
| MIL-PRF-13789 Revision E:1999 | Strainers, Sediment: Pipeline, Basket Type |
| FM 1112 : 2006 | INDICATING VALVES (BUTTERFLY OR BALL TYPE) |
| AWWA C518 : 2013 | DUAL-DISC SWING-CHECK VALVES FOR WATERWORKS SERVICE |
| AWWA C604:2017 | INSTALLATION OF BURIED STEEL WATER PIPE - 4 IN. (100 MM) AND LARGER |
| FM 1230 : 2013 | ANTI-WATER HAMMER CHECK VALVES |
| ASME B31.1 : 2016 | POWER PIPING |
| ASME A112.4.14 : 2017 | MANUALLY OPERATED QUARTER-TURN SHUTOFF VALVES FOR USE IN PLUMBING SYSTEMS |
| ASME B31.3:2016 | PROCESS PIPING |
| FM 1035 : 2014 | NITROGEN GENERATORS |
| FM 1056 : 2010 | SIGHT DRAINS FOR AUTOMATIC SPRINKLER SYSTEMS |
| AWWA C220 : 2017 | STAINLESS-STEEL PIPE, 1/2 IN. (13 MM) AND LARGER |
| AWWA C520 : 2014 | KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM) |
| FM 1530 : 2016 | FIRE DEPARTMENT CONNECTIONS |
| FM 5551 : 1963 | STRAINERS FOR USE WITH WATER BASED FIRE PROTECTION SYSTEMS |
| FM 1043 : 2011 | WATER FLOW DETECTOR TESTERS 1 INCH THROUGH 8 INCH NOMINAL SIZE |
| AWWA M41 : 3 | Ductile-Iron Pipe and Fittings, Third Edition |
| MIL-PRF-370 Revision K:2017 | Hose and Hose Assemblies, Nonmetallic: Elastomeric, Liquid Fuel |
| ASTM F 1476 : 2007 : R2013 | Standard Specification for Performance of Gasketed Mechanical Couplings for Use in Piping Applications |
| AWWA C517 : 2016 | RESILIENT-SEATED CAST-IRON ECCENTRIC PLUG VALVES |
| ASTM A 377 : 2003 : R2014 | Standard Index of Specifications for Ductile-Iron Pressure Pipe |
| MSS SP 139 : 2014 | COPPER ALLOY GATE, GLOBE, ANGLE, AND CHECK VALVES FOR LOW PRESSURE/LOW TEMPERATURE PLUMBING APPLICATIONS |
| MSS SP 67 : 2017 | BUTTERFLY VALVES |
| FM 1034 : 2013 | AIR DRYING UNITS |
| AWWA C150/A21.50 : 2014 | THICKNESS DESIGN OF DUCTILE-IRON PIPE |
| FM 1631 : 2006 | ADJUSTABLE AND FIXED SPRINKLER FITTINGS 1/2 INCH THROUGH 1 INCH NOMINAL SIZE |
| FM 1364 : 2013 | EXPANSION CHAMBERS |
| FM 1041 : 2006 | ALARM CHECK VALVES |
| NSF 61 : 2016 | DRINKING WATER SYSTEM COMPONENTS - HEALTH EFFECTS |
| AWWA C151/A21.51 : 2017 | DUCTILE-IRON PIPE, CENTRIFUGALLY CAST |
| ASTM A 183 : 2014 : REDLINE | Standard Specification for Carbon Steel Track Bolts and Nuts |
| NFPA 13 : 2016 | INSTALLATION OF SPRINKLER SYSTEMS |
| ASTM A 449 : 2014 : REDLINE | Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.