BS 18-1:1970
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Methods for tensile testing of metals Non-ferrous metals
Hardcopy , PDF
English
27-02-1970
23-07-2013
Definitions and symbols; form and dimensions of standard test pieces; test piece preparation and testing equipment. Procedures for determining tensile properties at room temperatures: proof stress, permanent stress, tensile strength, percentage elongation, with appropriate proving tests. Foreword gives guidance for drafting materials specification.
| Committee |
ISE/101
|
| DocumentType |
Standard
|
| Pages |
0
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy |
| BS 2898:1970 | Specification for wrought aluminium and aluminium alloys for electrical purposes. Bars, extruded round tube and sections |
| BS 4300-10(1969) : 1969 | WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES (SUPPLEMENTARY SERIES) - 5454 DRAWN TUBE |
| BS 4300-8(1969) : 1969 | SPECIFICATION (SUPPLEMENTARY SERIES) FOR WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES - 5454 PLATE, SHEET AND STRIP |
| BS 3348:1961 | Specification for antral trocars and cannulae |
| BS 4300-6(1969) : 1969 | SPECIFICATION (SUPPLEMENTARY SERIES) FOR WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES - 3105 SHEET AND STRIP |
| BS 4345:1968 | Specification for slotted angles |
| NES 822 PT 1 : ISSUE 2 | REQUIREMENTS FOR NICKEL CHROMIUM MOLYBDENUM NIOBIUM ALLOY 625 - CENTRIFUGAL CASTINGS |
| I.S. 97-2:1988 | WOOD SCREWS - PART 2: SCREWS WITH ROLLED THREADS |
| I.S. 97:1986 | WOOD SCREWS |
| BS 2870:1980 | Specification for rolled copper and copper alloys: sheet, strip and foil |
| BS 5154:1991 | Specification for copper alloy globe, globe stop and check, check and gate valves |
| BS 2897:1970 | Specification for wrought aluminium for electrical purposes. Strip with drawn or rolled edges |
| BS 5154:1989 | Specification for copper alloy globe, globe stop and check, check and gate valves |
| BS 6223:1990 | Specification for friction welding of joints in metals |
| BS 5950-1:1990 | Structural use of steelwork in building Code of practice for design in simple and continuous construction: hot rolled sections |
| BS 1473:1972 | Specification for wrought aluminium and aluminium alloys for general engineering purposes - rivet, bolt and screw stock |
| BS 5045-6:1987 | Transportable gas containers Specification for seamless containers of less than 0.5 litre water capacity |
| DEFSTAN 02-749(PT3)/1(2000) : 2000 | REQUIREMENTS FOR ALUMINIUM-NICKEL-SILICON-BRASS - PART 3: TUBES |
| BS 4990:1973 | Copper-clad aluminium conductors in insulated cables |
| BS DD89(1983) : 1983 | METHODS FOR TESTING AND ASSESSING THE PERFORMANCE OF PREFABRICATED HEAVY DUTY SUPPORT TOWERS |
| BS 4300-5(1973) : 1973 | WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES (SUPPLEMENTARY SERIES) - 2011 FREE CUTTING BAR AND WIRE |
| NES 822 PT 2 : ISSUE 2 | REQUIREMENTS FOR NICKEL CHROMIUM MOLYBDENUM NIOBIUM ALLOY 625 - SAND CASTINGS AND INGOTS |
| BS 2627:1970 | Specification for wrought aluminium for electrical purposes. Wire |
| BS 3075:1976 | Specification for nickel and nickel alloys: wire |
| BS 3071:1986 | Specification for nickel-copper alloy castings |
| BS 1400:1985 | Specification for copper alloy ingots and copper alloy and high conductivity copper castings |
| BS 4791:1985 | Specification for calorimeter bombs |
| BS 3073:1977 | Specification for nickel and nickel alloys: strip |
| BS 4300-7(1969) : 1969 | SPECIFICATION (SUPPLEMENTARY SERIES) FOR WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES - 5005 SHEET AND STRIP |
| DEFSTAN 61-12(PT16)SEC1/1(1977) : 1977 | WIRES, CORDS, AND CABLES, ELECTRICAL - METRIC UNITS - PART 16: AERIAL (ANTENNA) WIRES |
| BS 4300-14(1973) : 1973 | WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS FOR GENERAL ENGINEERING PURPOSES (SUPPLEMENTARY SERIES) - 7020 PLATE, SHEET STRIP |
| BS 5812-1:1979 | Materials for plain bearings. Specification for aluminium alloy for solid bearings |
| BS 1504:1976 | Specification for steel castings for pressure purposes |
| DEFSTAN 02-779(PT2)/1(2000) : 2000 | REQUIREMENTS FOR 90/10 COPPER NICKEL ALLOY MATERIAL - PART 2: FORGINGS, FORGING STOCK, RODS AND SECTIONS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.