BS 2782-0:2004
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Methods of testing plastics Introduction
Hardcopy , PDF
English
28-04-2004
30-09-2011
Foreword
1 Scope
2 Informative references
3 Content and usage of BS 2782
4 Units
5 Apparatus and reagents
6 Sampling
7 Number of test pieces
8 Preparation of test pieces
9 Direction of testing
10 Test report
11 Standard atmospheres for conditioning and testing
Annex A (informative) List of methods in BS 2782
published separately and degree of
equivalence of international standards
Annex B (informative) Method 508A; Rate of burning, laboratory
method
Bibliography
Figure
Table
This part of BS 2782 gives a general introduction to the methods of test for plastics some of which are presented in the other Parts. Annex A lists the individual methods and Annex B describes an obsolescent method (508A), formerly given in BS 2782:1970 and still referred to by the Building Regulations.
| Committee |
PRI/21
|
| DevelopmentNote |
Supersedes BS 2782-0(1995). (05/2004) Supersedes 02/123547 DC (11/2004) Reviewed and confirmed by BSI, January 2010. (12/2009)
|
| DocumentType |
Standard
|
| Pages |
34
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| BS 4618-4.1:1972 | Recommendations for the presentation of plastics design data. Environmental and chemical effects Chemical resistance to liquids |
| BS 4618-4.2:1972 | Recommendations for the presentation of plastics design data. Environmental and chemical effects Resistance to natural weathering |
| BS 4618-1.1:1970 | Recommendations for the presentation of plastics design data. Mechanical properties Creep |
| BS 4618-5.4:1972 | Recommendations for the presentation of plastics design data. Other properties Acoustical properties (mechanical damping capacity) |
| BS 4618-2.4:1975 | Recommendations for the presentation of plastics design data. Electrical properties Surface resistivity |
| BS 4618-4.4:1973 | Recommendations for the presentation of plastics design data. Environmental and chemical effects The effect of marine exposure |
| BS EN ISO 3696:1995 | Water for analytical laboratory use. Specification and test methods |
| BS 4618-4.5:1974 | Recommendations for the presentation of plastics design data. Environmental and chemical effects The effect on plastics of soil burial and biological attack |
| BS 4618-5.6:1975 | Recommendations for the presentation of plastics design data. Other properties Guide to sliding friction |
| BS 4618-2.2:1970 | Recommendations for the presentation of plastics design data. Electrical properties Loss tangent |
| BS 4618-3.1:1970 | Recommendations for the presentation of plastics design data. Thermal properties Linear thermal expansion |
| BS 4618-5.2:1970 | Recommendations for the presentation of plastics design data. Other properties Change in linear dimensions with moisture absorption |
| BS 4618-1.1.3:1974 | Recommendations for the presentation of plastics design data. Mechanical properties Creep lateral contraction ratio (Poisson\'s ratio) |
| BS 4618-1.3:1975 | Recommendations for the presentation of plastics design data. Mechanical properties Strength |
| BS 4618-1.1.2:1976 | Recommendations for the presentation of plastics design data. Mechanical properties Creep in flexure at low strains |
| BS 4618-4.6:1974 | Recommendations for the presentation of plastics design data. Environmental and chemical effects The thermal endurance of plastics |
| BS 4618-5.3:1972 | Recommendations for the presentation of plastics design data. Other properties Optical properties |
| BS 4618-3.2:1973 | Recommendations for the presentation of plastics design data. Thermal properties Heat content |
| BS EN ISO 291:2008 | Plastics. Standard atmospheres for conditioning and testing |
| BS 4618-5.1:1970 | Recommendations for the presentation of plastics design data. Other properties Density |
| BS 4618-1.1.1:1970 | Recommendations for the presentation of plastics design data. Mechanical properties Creep in uniaxial tension or compression (with particular reference to solid plastics) |
| BS 4618-1.3.1:1975 | Recommendations for the presentation of plastics design data. Mechanical properties Static fatigue failure |
| BS 4618-1.3.3:1976 | Recommendations for the presentation of plastics design data. Mechanical properties Environmental stress cracking |
| BS 4618-1.2:1972 | Recommendations for the presentation of plastics design data. Mechanical properties Impact behaviour |
| BS 4618-2.1:1970 | Recommendations for the presentation of plastics design data. Electrical properties Permittivity |
| BS 4618-5.5:1974 | Recommendations for the presentation of plastics design data. Other properties Data on diffusion |
| BS 4618-4.3:1974 | Recommendations for the presentation of plastics design data. Environmental and chemical effects Resistance to colour change produced by exposure to light |
| BS 4618-3.3:1973 | Recommendations for the presentation of plastics design data. Thermal properties Thermal conductivity |
| BS 4618-2.3:1975 | Recommendations for the presentation of plastics design data. Electrical properties Volume resistivity |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.