BS EN 10209:2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Cold rolled low carbon steel flat products for vitreous enameling. Technical delivery conditions
Hardcopy , PDF
English
31-07-2013
28-07-2023
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Designation
5 Requirements
6 Tests
7 Identification
8 Packaging
9 Disputes
10 Information to be supplied by the purchaser at the
time of ordering
Annex A (normative) - Methods for determining the resistance
to fish scaling of a steel sheet for enamelling
Annex B (normative) - Method for determining mass loss (iron loss)
due to pickling for steel grades for direct enamelling
in accordance with 5.4.2
Annex C (normative) - Method for determining the adherence level
of enamel applied to a steel sheet
Annex D (informative) - Characteristics for the selection of
enamelling steel grades
Pertains to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet.
| Committee |
ISE/109
|
| DevelopmentNote |
Supersedes BS 1449-1.3(1991) and 92/37552 DC. (07/2005) Supersedes 10/30227692 DC. (07/2013)
|
| DocumentType |
Standard
|
| Pages |
30
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard applies to cold rolled non-coated low carbon steel flat products in rolled widths equal to or over 600 mm and in thicknesses equal to or less than 3 mm, delivered in sheet, wide strip, slit wide strip or cut lengths obtained from slit wide strip or sheet. It does not apply to cold rolled narrow strip (rolling width < 600 mm) nor to cold rolled flat products for which there is a specific standard, in particular the following: cold-rolled low carbon steel flat products for cold forming (EN 10130); cold-rolled non oriented electrical steel sheet and strip delivered in fully processed state (EN 10106); cold rolled electrical non-alloy and alloy steel sheet and strip delivered in the semi-processed state (EN 10341); cold reduced blackplate (EN 10205); steel sheet and strip for welded gas cylinders (EN 10120); cold-rolled uncoated non-alloy mild steel narrow strip for cold forming (EN 10139); cold-rolled structural steels for general purposes; cold-rolled flat products made of high yield strength for cold forming (EN 10268).
| Standards | Relationship |
| EN 10209:2013 | Identical |
| NS EN 10209 : 2013 | Identical |
| NF EN 10209 : 2013 | Identical |
| NEN EN 10209 : 2013 | Identical |
| NBN EN 10209 : 2013 | Identical |
| I.S. EN 10209:2013 | Identical |
| DIN EN 10209:2013-09 | Equivalent |
| UNE-EN 10209:2013 | Identical |
| BS 7793-2:1996 | Vitreous enamel coatings for use on bolted steel panels Specification for coatings on bolted steel panels for use in industrial liquid storage tanks |
| EN 10079:2007 | Definition of steel products |
| EN 10027-2:2015 | Designation systems for steels - Part 2: Numerical system |
| EN ISO 6892-1:2016 | Metallic materials - Tensile testing - Part 1: Method of test at room temperature (ISO 6892-1:2016) |
| EN ISO 377:2017 | Steel and steel products - Location and preparation of samples and test pieces for mechanical testing (ISO 377:2017) |
| ISO 6892-1:2016 | Metallic materials — Tensile testing — Part 1: Method of test at room temperature |
| EN 10131:2006 | Cold rolled uncoated and zinc or zinc-nickel electrolytically coated low carbon and high yield strength steel flat products for cold forming - Tolerances on dimensions and shape |
| EN 10021:2006 | General technical delivery conditions for steel products |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| EN 10049:2013 | Measurement of roughness average Ra and peak count RPc on metallic flat products |
| EN 10027-1:2016 | Designation systems for steels - Part 1: Steel names |
| ISO 10113:2006 | Metallic materials — Sheet and strip — Determination of plastic strain ratio |
| ISO 377:2017 | Steel and steel products — Location and preparation of samples and test pieces for mechanical testing |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.