BS EN 12953-11:2003
Current
The latest, up-to-date edition.
Shell boilers Acceptance tests
Hardcopy , PDF
English
02-10-2003
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
4.1 Symbols and units
4.2 Coefficients
5 General
6 Basic test conditions
6.1 General conditions
6.2 Steady-state conditions
6.3 Test procedure
6.4 Requirements during test
6.5 Duration of tests
6.6 Procedure for the determination of exhaust gas temperature and
CO, CO[2] and O[2] content
6.7 Undetermined losses
7 Instrumentation and methods of measurements
7.1 Instruments
7.2 Pressure measurements
7.3 Temperature measurements
7.4 Mass and mass flow
7.5 Calorific values
7.6 Chemical composition
8 Heat balance and thermal efficiency
8.1 General
8.2 Envelope boundary
8.3 Reference temperature
8.4 Heat input
8.5 Losses
8.6 Determination of efficiency by indirect method
8.7 Useful heat output
9 Accuracy
Annex A (informative) Calculation of combustion air/flue gas mass to
fuel mass ratios and specific heat
A.1 Combustion air/flue gas mass to fuel mass ratios
A.2 Ultimate analysis
A.3 Statistical analysis
A.4 Specific heat of flue gas and combustion air
Annex B (normative) Waste heat boilers
B.1 General
B.2 Useful heat output
B.3 Heat from waste gases
B.4 Heat input
B.5 Thermal efficiency
B.6 Methods of measurement
Bibliography
Describes a concise procedure for conducting thermal performance tests, using the indirect (losses) procedure for boilers for steam or hot water.
| Committee |
PVE/2
|
| DevelopmentNote |
Supersedes 01/704690 DC (10/2003)
|
| DocumentType |
Standard
|
| Pages |
36
|
| PublisherName |
British Standards Institution
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| EN 12953-11:2003 | Identical |
| DIN EN 12953-11:2003-12 | Identical |
| I.S. EN 12953-11:2003 | Identical |
| NF EN 12953-11 : 2004 | Identical |
| NS EN 12953-11 : 1ED 2003 | Identical |
| NEN EN 12953-11 : 2003 | Identical |
| NBN EN 12953-11 : 2003 | Identical |
| UNE-EN 12953-11:2004 | Identical |
| EEMUA 193 : 2013 | MANAGING COMPETENCE ASSURANCE FOR PERSONNEL UNDERTAKING IN-SERVICE INSPECTION OF PRESSURE EQUIPMENT |
| VDI/VDE 2640 Blatt 3:1983-11 | Measurement of gas flow in circular; annular or rectangular sections of conduits velocity area method |
| ISO 3993:1984 | Liquefied petroleum gas and light hydrocarbons — Determination of density or relative density — Pressure hydrometer method |
| DIN 51700:2015-12 | TESTING OF SOLID FUELS - GENERALITIES AND INDEX OF METHODS OF TEST |
| ISO 157:1996 | Coal — Determination of forms of sulfur |
| VDI/VDE 3511 Blatt 4:1995-01 | Temperature measurement in industry - Radiation thermometry |
| ISO 6976:2016 | Natural gas — Calculation of calorific values, density, relative density and Wobbe indices from composition |
| VDI/VDE 2640 Blatt 4:1983-10 | Measurement of mean temperature in fluid flow |
| VDI 2066-3 : 1986 | MEASUREMENT OF PARTICULATE MATTER - MANUAL DUST MEASUREMENT IN FLOWING GASES - GRAVIMETRIC DETERMINATION OF DUST LOAD - TUBULAR FILTER DEVICE (40 M[3]/H) |
| ISO 3170:2004 | Petroleum liquids — Manual sampling |
| ISO 1928:2009 | Solid mineral fuels — Determination of gross calorific value by the bomb calorimetric method and calculation of net calorific value |
| VDI 2066 Blatt 4:1989-01 | Particulate matter measurement; measurement of particulate matter in flowing gases; determination of dust load by continuous; measurement of optical transmission |
| VDI/VDE 3511 : 1967 | TECHNICAL TEMPERATURE MEASUREMENTS |
| EN ISO 3993:1995 | Liquefied petroleum gas and light hydrocarbons - Determination of density or relative density - Pressure hydrometer method (ISO 3993:1984) |
| ISO 334:2013 | Solid mineral fuels — Determination of total sulfur — Eschka method |
| VDI 2066-2 : 1989 | MEASUREMENT OF PARTICULATE MATTER - MANUAL DUST MEASUREMENT IN FLOWING GASES - GRAVIMETRIC DETERMINATION OF DUST LOAD - TUBULAR FILTER DEVICES (4 M[3]/H, 12 M[3]/H) |
| VDI/VDE 3511 Blatt 2:1996-04 | Temperature measurement in industry - Contact thermometers |
| DIN 1871:1999-05 | Gaseous fuels and other gases - Density and other volumetric quantities |
| ISO/TR 5168:1998 | Measurement of fluid flow — Evaluation of uncertainties |
| EN ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003) |
| EN 437:2003+A1:2009 | Test gases - Test pressures - Appliance categories |
| EN 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 1: General principles and requirements |
| VDI 2066 Blatt 6:1989-01 | Particulate matter measurement; measurement of particulate matter in flowing gases; determination of dust load by continuous measurement of scattered light with the photometer KTN |
| IEC 60751:2008 | Industrial platinum resistance thermometers and platinum temperature sensors |
| DIN 51853:2011-12 | Testing of fuel gases - Sampling |
| NFX 44 052 : 2002 | STATIONARY SOURCE EMISSIONS - DETERMINATION OF HIGH RANGE MASS CONCENTRATION OF DUST - MANUAL GRAVIMETRIC METHOD |
| ISO 1988:1975 | Hard coal — Sampling |
| VDI 2066-5 : 1987 | PARTICULATE MATTER MEASUREMENT - DUST MEASUREMENT IN FLOWING GASES; PARTICLE SIZE SELECTIVE MEASUREMENT BY IMPACTION METHOD - CASCADE IMPACTOR |
| VDI 2066 Blatt 1:1975-10 | Particulate matter measurement; measuring of particulate matter in flowing gases; gravimetric determination of dust load; fundamentals |
| ISO 589:2008 | Hard coal — Determination of total moisture |
| EN 837-3:1996 | Pressure gauges - Part 3: Diaphragm and capsule pressure gauges - Dimensions, metrology, requirements and testing |
| IEC 60584-1:2013 | Thermocouples - Part 1: EMF specifications and tolerances |
| VDI/VDE 3511 Blatt 5:1994-11 | TEMPERATURE MEASUREMENT IN INDUSTRY - INSTALLATION OF THERMOMETERS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.