BS EN 13244-2:2002
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Polyethylene (PE) Pipes
Hardcopy , PDF
English
11-12-2003
30-11-2011
Foreword
Introduction
1 Scope
2 Normative references
3 Definitions, symbols and abbreviations
4 Material
4.1 Compound
4.2 Identification compound
5 General characteristics
5.1 Appearance
5.2 Colour
6 Geometrical characteristics
6.1 Measurement of dimensions
6.2 Mean outside diameters and out-of-roundness (ovality)
6.3 Wall thicknesses and their tolerances
6.4 Coiled pipe
6.5 Pipe lengths
6.6 Pipe stiffness
7 Mechanical characteristics
7.1 Conditioning
7.2 Requirements
7.3 Retest in case of failure at 80 degrees C
8 Physical characteristics
8.1 Conditioning
8.2 Requirements
9 Chemical characteristics of pipes in contact with chemicals
10 Performance requirements
11 Marking
11.1 General
11.2 Minimum required marking of pipes
Annex A (informative) - Relationship between PN, MRS, S and SDR
Annex B (normative) - Pipe stiffness
Bibliography
Describes the characteristics of pipes made from polyethylene (PE) intended for buried and above-ground pressure systems for water for general purposes, drainage and sewerage. Applicable to vacuum sewer systems.
| Committee |
PRI/88
|
| DevelopmentNote |
Together with BS EN 13244-1 and BS EN 13244-5, supersedes BS 6437(1984). Supersedes 98/122497 DC. (12/2003)
|
| DocumentType |
Standard
|
| Pages |
26
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| NS EN 13244-2 : 1ED 2003 | Identical |
| NF EN 13244-2 : 2003 | Identical |
| EN 13244-2:2002 | Identical |
| NBN EN 13244-2 : 2003 | Identical |
| NEN EN 13244-2 : 2003 | Identical |
| I.S. EN 13244-2:2002 | Identical |
| DIN EN 13244-2:2003-04 | Identical |
| 07/30138205 DC : DRAFT MAR 2007 | BS 6297 - DESIGN AND INSTALLATION OF SMALL SEWAGE TREATMENT WORKS AND CESSPOOLS - CODE OF PRACTICE |
| BS EN 15014:2007 | Plastics piping systems. Buried and above ground systems for water and other fluids under pressure. Performance characteristics for pipes, fittings and their joints |
| EN 15014:2007 | Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints |
| EN 13244-1:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 1: General |
| ISO/TR 10358:1993 | Plastics pipes and fittings — Combined chemical-resistance classification table |
| EN 728:1997 | Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time |
| BS EN 681-1:1996 | Elastomeric seals. Material requirements for pipe joint seals used in water and drainage applications Vulcanized rubber |
| ISO 4433-1:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 1: Immersion test method |
| EN ISO 6259-1:2015 | Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015) |
| ISO 11922-1:1997 | Thermoplastics pipes for the conveyance of fluids — Dimensions and tolerances — Part 1: Metric series |
| BS 7874:1998 | Method of test for microbiological deterioration of elastomeric seals for joints in pipework and pipelines |
| EN 921:1994/AC:1995 | PLASTICS PIPING SYSTEMS - THERMOPLASTICS PIPES - DETERMINATION OF RESISTANCE TO INTERNAL PRESSURE AT CONSTANT TEMPERATURE |
| ISO 4433-2:1997 | Thermoplastics pipes — Resistance to liquid chemicals — Classification — Part 2: Polyolefin pipes |
| PREN ISO 3126 : DRAFT 1999 | PLASTICS PIPING SYSTEMS - PLASTICS PIPING COMPONENTS - MEASUREMENT AND DETERMINATION OF DIMENSIONS |
| ISO 4065:1996 | Thermoplastics pipes — Universal wall thickness table |
| ISO 6259-3:2015 | Thermoplastics pipes — Determination of tensile properties — Part 3: Polyolefin pipes |
| EN ISO 1133:2005 | Plastics - Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics (ISO 1133:2005) |
| BS EN ISO 13479:2009 | Polyolefin pipes for the conveyance of fluids — Determination of resistance to crack propagation — Test method for slow crack growth on notched pipes |
| EN 13244-5:2002 | Plastics piping systems for buried and above-ground pressure systems for water for general purposes, drainage and sewerage - Polyethylene (PE) - Part 5: Fitness for purpose of the system |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.