BS EN 20286-2:1993
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
ISO system of limits and fits ISO system of limits and fits. Tables of standard tolerance grades and limit deviations for holes and shafts
Hardcopy , PDF
English
31-01-1990
31-07-2010
National foreword
Committees responsible
Specification
0. Introduction
1. Scope
2. Field of application
3. References
4. Standard tolerances
5. Limit deviations for holes
6. Limit deviations for shafts
7. Bibliography
Annex
Graphical review of tolerance zones of holes and shafts
Tables
1. Numerical values of standard tolerance grades IT
for basic sizes up to 3 150 mm
2. Limit deviations for holes A, B and C
3. Limit deviations for holes CD, D and E
4. Limit deviations for holes EF and F
5. Limit deviations for hoels FG and G
6. Limit deviations for holes H
7. Limit deviations for holes JS
8. Limit deviations for holes J and K
9. Limit deviations for holes M and N
10. Limit deviations for holes R
12. Limit deviations for holes S
13. Limit deviations for holes T and U
14. Limit deviations for holes V, X and Y
15. Limit deviations for holes Z and ZA
16. Limit deviations for holes ZB and ZC
17. Limit deviations for shafts a, b and c
18. Limit deviations for shafts cd and d
19. Limit deviations for shafts e and ef
20. Limit deviations for shafts f and fg
21. Limit deviations for shafts g
22. Limit deviations for shafts h
23. Limit deviations for shafts js
24. Limit deviations for shafts j and k
25. Limit deviations for shafts m and n
26. Limit deviations for shafts p
27. Limit deviations for shafts r
28. Limit deviations for shafts s
29. Limit deviations for shafts t and u
30. Limit deviations for shafts v, x and y
31. Limit deviations for shafts z and za
32. Limit deviations for shafts zb and zc
Figures
1. Upper and lower deviations
2. Synoptic representation of tolerance classes for
holes for basic sizes less than or equal to 500 mm
3. Synoptic representation of tolerance classes for
holes for basic sizes greater than 500 mm and less
than or equal to 3 150 mm
4. Synoptic representation of tolerance classes for
shafts for basic sizes less than or equal to 500 mm
5. Synoptic representation of tolerance classes for
shafts for basic sizes greater than 500 mm and less
than or equal to 3 150 mm
6. Graphical review of tolerance classes for holes in
terms of fundamental deviations
7. Graphical review of tolerance classes for holes in
terms of standard tolerances grades
8. Graphical review of tolerance classes for shafts in
terms of fundamental deviations
9. Graphical review of tolerance classes for shafts in
terms of standard tolerance grades
Calculated from the information given in Part 1.
| Committee |
TPR/1
|
| DevelopmentNote |
Supersedes and renumbers BS 4500-1.2(1990) (07/2004)
|
| DocumentType |
Standard
|
| Pages |
54
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| ISO 286-2:2010 | Identical |
| EN 20286-2 : 1993 | Identical |
| NF EN 20286-2 : 1993 | Identical |
| I.S. EN 20286-2:1994 | Identical |
| NBN EN 20286-2 : 1993 | Identical |
| ISO 286-2:1988 | Identical |
| UNE-EN 20286-2:1996 | Identical |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.