BS EN 50083-3:1999
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Cabled distribution systems for television and sound signals Active wideband equipment for coaxial cable networks
Hardcopy , PDF
English
15-04-1999
30-06-2006
Foreword
1 Scope
1.1 General
1.2 Specific scope of this part
2 Normative references
3 Terms, definitions, symbols and abbreviations
3.1 Terms and definitions
3.2 Symbols
3.3 Abbreviations
4 Methods of measurement
4.1 Linear distortion
4.2 Non-linear distortion
4.3 Automatic gain and slope control step response
4.4 Noise figure
5 System performance
5.1 General requirements
5.2 Safety
5.3 Electromagnetic compatibility (EMC)
5.4 Frequency range
5.5 Impedance and return loss
5.6 Gain
5.7 Flatness
5.8 Test points
5.9 Group delay
5.10 Noise figure
5.11 Non-linear distortion
5.12 Automatic gain and slope control
5.13 Hum modulation
5.14 Power supply
5.15 Environmental
5.16 Marking
5.17 Mean operating time between failure (MTBF)
Annex A (normative) Test carriers, levels and intermodulation
products
Annex B (normative) Checks on test equipment
Annex C (normative) Frequency allocation plan
Annex D (normative) Special national conditions
Annex E (informative) Measurement errors which occur due to
mismatched equipment
Figure 1 Measurement of return loss
Figure 2 Maximum error a for measurement of return loss
using V.S.W.R. bridge with directivity
D = 46 dB and 26 dB test port return loss
Figure 3 Basic arrangement of test equipment for evaluation
of the ratio of signal to intrermodulation product
Figure 4 Connection of test equipment for the measurement of
non-linear distortion by composite beat
Figure 5 Connection of test equipment for the measurement of
composite cross-modulation
Figure 6 Carrier/hum ratio = 20 lgA/a(dB)
Figure 7 Test set-up for local-powered objects
Figure 8 Test set-up for remote-powered objects
Figure 9 Oscilloscope display
Figure 10 Measurement of AGC step response
Figure 11 Time constant Tc
Figure 12 Measurement of noise figure
Figures A.1, A.2 and A.3
Figure E.1 Error concerning return loss measurement
Figure E.2 Maximum ripple
Table 1 Return loss requirements for all equipment
Table 2 Correction factors where the modulation used is
other than 100%
Table C.1
Covers measurement of operational characteristics of one-way and two-way active equipment to assess its performance and identifies specifications to be published by manufacturers.
| Committee |
PTI/12
|
| DevelopmentNote |
Renumbered and superseded by BS EN 60728-3. (07/2006) Supersedes 97/205212 DC. (03/2007)
|
| DocumentType |
Standard
|
| Pages |
28
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| I.S. EN 50083-3:2002 | Identical |
| NEN EN 50083-3 : 2002 | Identical |
| EN 50083-3:2002 | Identical |
| NF EN 50083-3 : 2005 | Identical |
| NBN EN 50083-3 : 1999 | Identical |
| EN 50083-3:1998 | Identical |
| UNE-EN 50083-3:2002 | Identical |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.