BS EN 62196-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Plugs, socket-outlets, vehicle connectors and vehicle inlets. Conductive charging of electric vehicles General requirements
Hardcopy , PDF
English
31-01-2015
22-11-2022
| Committee |
PEL/23
|
| DevelopmentNote |
Supersedes 01/202446 DC (05/2004). 2003 version remains current. Supersedes 10/30216162 DC. (06/2012) 2012 Edition remains current and will be withdrawn on 15/10/2017. (07/2013) 2012 + A11 2013 Edition remains active & will be withdrawn on 16/06/2017. Supersedes 13/30295015 DC. (10/2014) 2012 + A12 2014 Edition remains active & will be withdrawn on 29/09/2019. Supersedes 13/30277668 DC. (02/2015)
|
| DocumentType |
Standard
|
| Pages |
92
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This part of IEC62196 is applicable to plugs, socket-outlets, vehicle connectors, vehicle inlets and cable assemblies for electric vehicles, herein referred to as “accessories”, intended for use in conductive charging systems which incorporate control means, with a rated operating voltage not exceeding 690V a.c. 50Hz to 60Hz, at a rated current not exceeding 250A, 1500V d.c. at a rated current not exceeding 400A. These accessories are intended to be installed by instructed persons ( IEC60050‑195:1998 , IEC60050‑195/AMD1:2001, 195-04-02) or skilled persons ( IEC60050‑195:1998 , IEC60050‑195/AMD1:2001, 195-04-01) only. These accessories and cable assemblies are intended to be used for circuits specified in IEC61851‑1 which operate at different voltages and frequencies and which may include extra-low voltage and communication signals. These accessories and cable assemblies are to be used at an ambient temperature between -30°C and+50°C. NOTE1 In some countries, other requirements may apply. NOTE2 the following countries, -35°C applies: SE. These accessories are intended to be connected only to cables with copper or copper-alloy conductors. The accessories covered by this part of IEC62196 are for use in certain modes of charging electric vehicles. These modes are defined in IEC61851‑1 . These definitions and a description of the types of connection (cases A, B and C), are described in IEC61851‑1:2010, 6.2 and 6.3.1. NOTE3 In the following countries, mode 1 will not be allowed: UK, US, CA, SG. This part of IEC62196 does not apply to those standardised accessories used in charging systems where the use of such accessories constructed to the requirements of other standards is permitted (e.g. in mode 1 and mode 2). Such standardized accessories may be used for those situations (mode and case) identified in IEC61851‑1 . This part of IEC62196 may be used as a guide for accessories with a lesser number of contacts and lower ratings for use with light duty vehicles.
| Standards | Relationship |
| EN 62196-1:2014 | Identical |
| NF EN 62196-1 : 2015 | Identical |
| NBN EN 62196-1 : 2015 | Identical |
| I.S. EN 62196-1:2014 | Identical |
| DIN EN 62196-1 : 2015 | Identical |
| UNE-EN 62196-1:2015 | Identical |
A newer version of this standard is available.
View Current Edition
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.