BS EN 62271-100 : 2009
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
HIGH-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 100: ALTERNATING-CURRENT CIRCUIT-BREAKERS (IEC 62271-100:2008)
Hardcopy , PDF
English
01-01-2013
01-10-2021
FOREWORD
1 General
2 Normal and special service conditions
3 Terms and definitions
4 Ratings
5 Design and construction
6 Type tests
7 Routine tests
8 Guidance to the selection of circuit-breakers
for service
9 Information to be given with enquiries, tenders
and orders
10 Rules for transport, storage, installation,
operation and maintenance
11 Safety
12 Influence of the product on the environment
Annex A (normative) - Calculation of transient recovery
voltages for short-line faults from rated
characteristics
Annex B (normative) - Tolerances on test quantities during
type tests
Annex C (normative) - Records and reports of type tests
Annex D (normative) - Determination of short-circuit power
factor
Annex E (normative) - Method of drawing the envelope of the
prospective transient recovery voltage of a circuit
and determining the representative parameters
Annex F (normative) - Methods of determining prospective
transient recovery voltage waves
Annex G (normative) - Rationale behind introduction of
circuit-breakers class E2
Annex H (informative) - Inrush currents of single and
back-to-back capacitor banks
Annex I (informative) - Explanatory notes
Annex J (informative) - Test current and line length
tolerances for short-line fault testing
Annex K (informative) - List of symbols and abbreviations
used in this standard
Annex L (informative) - Explanatory notes on the revision
of TRVs for circuit-breakers of rated voltages higher
than 1 kV and less than 100 kV
Annex M (normative) - Requirements for breaking of
transformer-limited faults by circuit-breakers with
rated voltage higher than 1 kV
Annex N (normative) - Use of mechanical characteristics and
and related requirements
Annex O (informative) - Guidance for short-circuit and switching
test procedures for metal-enclosed and dead tank
circuit-breakers
Annex P (normative) - Calculation of the TRV parameters during
asymmetrical fault condition (T100a)
Annex Q (informative) - Examples for the application of the
asymmetry criteria during asymmetrical test-duty T100a
Annex R (normative) - Requirements for circuit-breakers with
opening resistors
Bibliography
Annex ZA (normative) - Normative references to international
publications with their corresponding European
publications
Pertains to a.c. circuit-breakers designed for indoor or outdoor installation and for operation at frequencies of 50 Hz and 60 Hz on systems having voltages above 1000 V.
| Committee |
PEL/17/1
|
| DevelopmentNote |
Supersedes BS 5311(1996). (04/2002) Supersedes 03/104001 DC. (03/2007) Supersedes BS PD IEC TR 62271-308. (07/2009) 2009 Edition Re-Issued in April 2018 & incorporates AMD 2 2017. Supersedes 15/30297958 DC. (05/2018)
|
| DocumentType |
Standard
|
| Pages |
456
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| Supersedes |
| Standards | Relationship |
| I.S. EN 62271-100:2009 | Identical |
| NF EN 62271-100 : 2009 AMD 2 2017 | Identical |
| IEC 62271-100:2008+AMD1:2012+AMD2:2017 CSV | Identical |
| NBN EN 62271-100 : 2009 AMD 1 2013 | Identical |
| EN 62271-100:2009 | Equivalent |
| EN 62271-100 : 2009 AMD 2/COR 18 | Identical |
| DIN EN 62271-100 : 2018-04 | Identical |
| UNE-EN 62271-100:2011 | Identical |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.