BS EN 74-1:2005
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Couplers, spigot pins and baseplates for use in falsework and scaffolds Part 1: Couplers for tubes. Requirements and test procedures
Hardcopy , PDF
English
31-08-2006
28-04-2022
| Committee |
B/514/21
|
| DevelopmentNote |
Supersedes BS 1139-2.1(1991) & 02/107768 DC (08/2006)
|
| DocumentType |
Standard
|
| Pages |
48
|
| PublisherName |
British Standards Institution
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
This European Standard specifies, for right angle couplers, swivel couplers, sleeve couplers and parallel couplers working by friction: materials; design requirements; strength classes with different structural parameters including values for resistance and stiffness; test procedures; assessment and gives recommendations for ongoing production control. For testing, screw couplers are tightened to a torque of 50 Nm and wedge couplers are tightened with a 500 g hammer until the jarring blow.
| Standards | Relationship |
| NS EN 74-1 : 1ED 2005 | Identical |
| NF EN 74-1 : 2006 | Identical |
| NEN EN 74-1 : 2005 | Identical |
| I.S. EN 74-1:2005 | Identical |
| NBN EN 74-1 : 2006 | Identical |
| EN 74-1:2005 | Identical |
| DIN EN 74-1:2005-12 | Identical |
| UNE-EN 74-1:2005 | Equivalent |
| UNE-EN 74-1:2008 | Identical |
| 17/30349707 DC : DRAFT AUG 2017 | BS 5975:2018 - CODE OF PRACTICE FOR TEMPORARY WORKS PROCEDURES AND THE PERMISSIBLE STRESS DESIGN OF FALSEWORK |
| BS 1139-2.2(2009) : 2009 | METAL SCAFFOLDING - PART 2: COUPLERS AND FITTINGS - SECTION 2.2: COUPLERS AND FITTINGS OUTSIDE THE SCOPE OF BS EN 74 - REQUIREMENTS AND TEST METHODS |
| BS 5975(2008) : 2008 | CODE OF PRACTICE FOR TEMPORARY WORKS PROCEDURES AND THE PERMISSIBLE STRESS DESIGN OF FALSEWORK |
| BS 5974:2010 | Code of practice for the planning, design, setting up and use of temporary suspended access equipment |
| BS 5974:2017 | Planning, design, setting up and use of temporary suspended access equipment. Code of practice |
| 17/30343371 DC : 0 | BS 5974 - PLANNING, DESIGN, SETTING UP AND USE OF TEMPORARY SUSPENDED ACCESS EQUIPMENT - CODE OF PRACTICE |
| 08/30181828 DC : DRAFT MAY 2008 | BS 5979 - CODE OF PRACTICE FOR THE PLANNING, DESIGN, SETTING UP AND USE OF TEMPORARILY INSTALLED SUSPENDED ACCESS EQUIPMENT |
| 09/30150058 DC : 0 | BS 1139-2.2 - METAL SCAFFOLDING - PART 2: COUPLERS - SECTION 2.2: ALUMINIUM COUPLERS AND SPECIAL COUPLERS IN STEEL - REQUIREMENTS AND TEST METHODS |
| 07/30150912 DC : 0 | BS 5975 - CODE OF PRACTICE FOR THE PROCEDURAL CONTROL OF TEMPORARY WORKS AND THE PERMISSIBLE STRESS DESIGN OF FALSEWORK |
| EN 12811-1:2003 | Temporary works equipment - Part 1: Scaffolds - Performance requirements and general design |
| EN 10002-1 : 2001 | METALLIC MATERIALS - TENSILE TESTING - PART 1: METHOD OF TEST AT AMBIENT TEMPERATURE |
| ISO 898-2:2012 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 2: Nuts with specified property classes — Coarse thread and fine pitch thread |
| EN 12811-2:2004 | Temporary works equipment - Part 2: Information on materials |
| ISO 965-5:1998 | ISO general purpose metric screw threads — Tolerances — Part 5: Limits of sizes for internal screw threads to mate with hot-dip galvanized external screw threads with maximum size of tolerance position h before galvanizing |
| EN 12812:2008 | Falsework - Performance requirements and general design |
| EN 12811-3:2002 | Temporary works equipment - Part 3: Load testing |
| ISO 2859:1974 | Sampling procedures and tables for inspection by attributes |
| ISO 965-2:1998 | ISO general purpose metric screw threads — Tolerances — Part 2: Limits of sizes for general purpose external and internal screw threads — Medium quality |
| EN 20898-2 : 1993 | MECHANICAL PROPERTIES OF FASTENERS - PART 2: NUTS WITH SPECIFIED PROOF LOAD VALUES - COARSE THREAD (ISO 898-2:1992) |
| ISO 965-4:1998 | ISO general purpose metric screw threads — Tolerances — Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing |
| EN ISO 9001:2015 | Quality management systems - Requirements (ISO 9001:2015) |
| EN 10204:2004 | Metallic products - Types of inspection documents |
| ISO 9001:2015 | Quality management systems — Requirements |
| EN ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts, screws and studs with specified property classes - Coarse thread and fine pitch thread (ISO 898-1:2013) |
| ISO 965-1:2013 | ISO general purpose metric screw threads — Tolerances — Part 1: Principles and basic data |
| EN 12810-1:2003 | Façade scaffolds made of prefabricated components - Part 1: Products specifications |
| ISO 965-3:1998 | ISO general purpose metric screw threads — Tolerances — Part 3: Deviations for constructional screw threads |
| ISO 898-1:2013 | Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws and studs with specified property classes — Coarse thread and fine pitch thread |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.