CGA E 9 : 2017
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
STANDARD FOR ETFE-LINED AND PTFE-LINED FLEXIBLE HOSES FOR COMPRESSED GAS SERVICE
12-01-2013
06-05-2021
1 Introduction
2 Scope
3 Definitions
4 Materials
5 Construction
6 Performance
7 Standard requirements
8 Oxygen installation considerations for PTFE-lined
flexible hoses
9 References
10 Additional references
Specifies a minimum standard for braided, ethylene tetrafluoroethylene (ETFE)-lined and pol-ytetrafluoroethylene (PTFE)-lined flexible hoses that have a nominal inside diameter (ID) of 0.25 in (6.4 mm) or less and shall have a maximum allowable working pressure (MAWP) of 3000 psi (20680 kPa) at 70 degrees F (21.1 degrees C).
| DocumentType |
Standard
|
| PublisherName |
Compressed Gas Association
|
| Status |
Superseded
|
| SupersededBy |
| CGA E 11 : 2015 | STATIONARY COMPRESSED GAS CYLINDER DISCHARGING MANIFOLDS FOR WORKING PRESSURES UP TO 3000 PSI |
| ASTM F 2318 : 2015 | Standard Specification for Rotary Wing Basic Life Support, Advanced Life Support, and Specialized Medical Support Air Ambulances (Withdrawn 2024) |
| I.S. EN ISO 21969:2009 | HIGH-PRESSURE FLEXIBLE CONNECTIONS FOR USE WITH MEDICAL GAS SYSTEMS |
| CGA E 16 : 2015 | STANDARD FOR COMPRESSED GAS CHECK VALVES FOR PRESSURES UP TO 3000 PSI |
| DIN EN ISO 14113:2014-02 | GAS WELDING EQUIPMENT - RUBBER AND PLASTICS HOSE AND HOSE ASSEMBLIES FOR USE WITH INDUSTRIAL GASES UP TO 450 BAR (45 MPA) (ISO 14113:2013) |
| BS EN ISO 21969:2009 | High-pressure flexible connections for use with medical gas systems |
| CGA G 6.6 : 2015 | STANDARD FOR CARBON DIOXIDE BULK TRANSFER HOSES |
| CGA G 4.10 : 2017 | USE OF NONMETALLIC MATERIALS IN HIGH PRESSURE OXYGEN BREATHING GAS APPLICATIONS |
| ISO 21969:2009 | High-pressure flexible connections for use with medical gas systems |
| ISO 14113:2013 | Gas welding equipment — Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) |
| EN ISO 14113:2013 | Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013) |
| CGA E 3 : 2008(R2014) | LOW PRESSURE PIPELINE STATION OUTLET/REGULATOR INLET CONNECTION STANDARD |
| BS EN ISO 14113:2013 | Gas welding equipment. Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) |
| EN ISO 21969:2009 | High-pressure flexible connections for use with medical gas systems (ISO 21969:2009) |
| UNE-EN ISO 21969:2010 | High-pressure flexible connections for use with medical gas systems (ISO 21969:2009) |
| UNE-EN ISO 14113:2013 | Gas welding equipment - Rubber and plastics hose and hose assemblies for use with industrial gases up to 450 bar (45 MPa) (ISO 14113:2013) |
| CGA E 11 : 2015 | STATIONARY COMPRESSED GAS CYLINDER DISCHARGING MANIFOLDS FOR WORKING PRESSURES UP TO 3000 PSI |
| CGA E 3 : 2008(R2014) | LOW PRESSURE PIPELINE STATION OUTLET/REGULATOR INLET CONNECTION STANDARD |