DD ENV 1090-6:2001
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
Execution of steel structures Supplementary rules for stainless steel
Hardcopy , PDF
English
15-08-2001
31-12-2008
FOREWORD
INTRODUCTION
1 SCOPE
2 NORMATIVE REFERENCES
3 DEFINITIONS
4 DOCUMENTATION
5 MATERIALS
6 FABRICATION
7 WELDING
8 MECHANICAL FASTENING
9 ERECTION
10 PROTECTIVE TREATMENT
11 GEOMETRICAL TOLERANCES
12 INSPECTION, TESTING AND CORRECTIONS
ANNEX A (Normative) PROCEDURE TESTS FOR PRELOADING BOLTS
AND DETERMINATION OF SLIP FACTOR
ANNEX B (Normative) RIVETING
ANNEX C (Informative) PROJECT SPECIFICATION
ANNEX D (Informative) CLASSIFICATION OF FABRICATED STEEL
COMPONENTS AND SYSTEMS FOR THE CONTROL OF
CONFORMITY
ANNEX E (Informative) GUIDELINES FOR WELDING COORDINATION
ANNEX F (Informative) HEXAGON INJECTION BOLTS
ANNEX G (Informative) GUIDELINES FOR INSPECTION AND TEST
PLAN
ANNEX H (Informative) GUIDELINES FOR WELD IMPERFECTION
LIMITS
ANNEX J (Informative) SELECTION AND USE OF MECHANICAL
FASTENERS FOR SHEETING
ANNEX L (Informative) GUIDANCE FOR BENDING OF CIRCULAR
TUBES
ANNEX M (Informative) BIBLIOGRAPHY
Refers to the specific requirements for execution of structural steelwork produced from stainless steel products and for structures that are not significantly susceptible to fatigue.
| Committee |
CB/203
|
| DocumentType |
Standard
|
| Pages |
44
|
| PublisherName |
British Standards Institution
|
| RevisionOf | |
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ENV 1090-6 : DRAFT 2000 | Identical |
| UNE-ENV 1090-6:2001 | Equivalent |
| BS PD6705-2(2010) : 2010 | STRUCTURAL USE OF STEEL AND ALUMINIUM - PART 2: RECOMMENDATIONS FOR THE EXECUTION OF STEEL BRIDGES TO BS EN 1090-2 |
| ENV 1993-1-4 : DRAFT 96 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - GENERAL RULES - SUPPLEMENTARY RULES FOR STAINLESS STEELS |
| EN 10048:1996 | Hot rolled narrow steel strip - Tolerances on dimensions and shape |
| EN ISO 3506-1:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 1: Bolts, screws and studs (ISO 3506-1:2009) |
| EN ISO 3506-3:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress (ISO 3506-3:2009) |
| PREN 10272 : DRAFT 2013 | STAINLESS STEEL BARS FOR PRESSURE PURPOSES |
| EN 10088-3:2014 | Stainless steels - Part 3: Technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products of corrosion resisting steels for general purposes |
| EN 1011-1:2009 | Welding - Recommendations for welding of metallic materials - Part 1: General guidance for arc welding |
| ENV 1090-1 : DRAFT 1996 | EXECUTION OF STEEL STRUCTURES - GENERAL RULES AND RULES FOR BUILDINGS |
| EN 10088-2:2014 | Stainless steels - Part 2: Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes |
| PREN 10028-7 : DRAFT 2013 | FLAT PRODUCTS MADE OF STEELS FOR PRESSURE PURPOSES - PART 7: STAINLESS STEELS |
| EURONORM 60 : 1977 | HOT-ROLLED ROUND STEEL FOR GENERAL USE |
| EURONORM 65 : 1980 | HOT-ROLLED ROUND STEEL FOR SCREWS AND RIVETS |
| EURONORM 61 : 1982 | HOT-ROLLED HEXAGON STEEL |
| EURONORM 58 : 1978 | HOT-ROLLED FLAT STEEL FOR GENERAL USE |
| ENV 1090-3 : DRAFT 1997 | EXECUTION OF STEEL STRUCTURES - PART 3: SUPPLEMENTARY RULES FOR HIGH YIELD STRENGTH STEELS |
| EN 12062:1997/A2:2003 | NON-DESTRUCTIVE EXAMINATION OF WELDS - GENERAL RULES FOR METALLIC MATERIALS |
| ENV 1090-6 : DRAFT 2000 | EXECUTION OF STEEL STRUCTURES - PART 6 - SUPPLEMENTARY RULES FOR STAINLESS STEEL |
| ENV 1090-4 : DRAFT 1997 | EXECUTION OF STEEL STRUCTURES - SUPPLEMENTARY RULES FOR HOLLOW SECTION STRUCTURES |
| ENV 1090-2 : DRAFT 1998 | EXECUTION OF STEEL STRUCTURES - SUPPLEMENTARY RULES FOR COLD FORMED THIN GAUGE COMPONENTS AND SHEETING |
| ENV 1993-1-3:1996/AC:1997 | EUROCODE 3: DESIGN OF STEEL STRUCTURES - GENERAL RULES - SUPPLEMENTARY RULES FOR COLD FORMED THIN GAUGE MEMBERS AND SHEETING |
| EN ISO 14555:2017 | Welding - Arc stud welding of metallic materials (ISO 14555:2017) |
| EURONORM 59 : 1978 | HOT-ROLLED SQUARE STEEL FOR GENERAL USE |
| EN 10258 : 1997 | COLD-ROLLED STAINLESS STEEL AND NARROW STRIP AND CUT LENGTHS - TOLERANCES AND DIMENSIONS AND SHAPE |
| EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
| PREN 10217-7 : DRAFT 2009 | WELDED STEEL TUBES FOR PRESSURE PURPOSES - TECHNICAL DELIVERY CONDITIONS - PART 7: STAINLESS STEEL TUBES |
| EN 970:1997 | Non-destructive examination of fusion welds - Visual examination |
| ISO 3269:2000 | Fasteners — Acceptance inspection |
| EN 10259 : 1997 | COLD-ROLLED STAINLESS STEEL WIDE STRIP AND PLATE/SHEET - TOLERANCES ON DIMENSIONS AND SHAPE |
| EURONORM 17 : 1970 | WIRE ROD OF COMMON UNALLOYED STEELS FOR DRAWING; DIMENSIONS AND PERMISSIBLE DEVIATIONS |
| ISO 1127:1992 | Stainless steel tubes — Dimensions, tolerances and conventional masses per unit length |
| EN ISO 3506-2:2009 | Mechanical properties of corrosion-resistant stainless steel fasteners - Part 2: Nuts (ISO 3506-2:2009) |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.