• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

DD ENV 13801:2001

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure. Thermoplastics. Recommended practice for installation

Available format(s)

Hardcopy , PDF

Superseded date

30-04-2014

Language(s)

English

Published date

15-08-2001

Foreword
Introduction
1 Scope
2 Normative references
3 Terminology, definitions, symbols and abbreviations
   3.1 General terminology
   3.2 Definitions
   3.3 Symbols
   3.4 Abbreviations
4 Design limits of the system
5 Storage, transport and handling
   5.1 General
   5.2 Transport
   5.3 Storage
   5.4 Handling on site
6 Installation
   6.1 General recommendations for installation
   6.2 Recommendations for above-ground installation
   6.3 Recommendations for installation in buried
        conditions
   6.4 Jointing procedure
7 Special precautions
   7.1 Concreting of thermoplastics systems within the
        building structure
   7.2 Foaming of thermoplastics systems
   7.3 Prevention of additional stresses in pipe work
8 Jointing to other materials or other constructions
   8.1 General
   8.2 Solvent-cement joints
   8.3 Ring seal joints
   8.4 Jointing to non-thermoplastics components
   8.5 Adaptors
9 Environmental aspects
10 Fire resistance of pipe work
11 Testing and inspection of installations
   11.1 Testing
   11.2 General inspection
12 Maintenance and cleaning of installations
   12.1 General
   12.2 Cleaning and descaling techniques
13 Chemical resistance of thermoplastics materials
Bibliography

Gives the recommended practice for installation of thermoplastics piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with 'B') and of soil and waste discharge systems for both inside buildings and buried in ground within the building structure (marked with 'BD').

Committee
PRI/88/1
DocumentType
Standard
Pages
52
PublisherName
British Standards Institution
RevisionOf
Status
Superseded
SupersededBy

Standards Relationship
ENV 13801:2000 Identical

ISO 8283-4:1992 Plastics pipes and fittings Dimensions of sockets and spigots for discharge systems inside buildings Part 4: Acrylonitrile/butadiene/styrene (ABS)
ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
EN 12056-2:2000 Gravity drainage systems inside buildings - Part 2: Sanitary pipework, layout and calculation
EN 1566-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
EN 1453-1:2017/AC:2017 PLASTICS PIPING SYSTEMS WITH STRUCTURED-WALL PIPES FOR SOIL AND WASTE DISCHARGE (LOW AND HIGH TEMPERATURE) INSIDE BUILDINGS - UNPLASTICIZED POLY(VINYL CHLORIDE) (PVC-U) - PART 1: SPECIFICATIONS FOR PIPES AND THE SYSTEM
ISO 8283-2:1992 Plastics pipes and fittings Dimensions of sockets and spigots for discharge systems inside buildings Part 2: Polyethylene (PE)
EN 12056-1:2000 Gravity drainage systems inside buildings - Part 1: General and performance requirements
EN 1455-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system
PREN 13476-1 : DRAFT 2015 PLASTICS PIPING SYSTEMS FOR NON-PRESSURE UNDERGROUND DRAINAGE AND SEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYLSEWERAGE - STRUCTURED-WALL PIPING SYSTEMS OF UNPLASTICIZED POLY(VINYL - PART 1: GENERAL REQUIREMENTS AND PERFORMANCE CHARACTERISTICS
EN 1519-1:1999 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
EN 12056-3:2000 Gravity drainage systems inside buildings - Part 3: Roof drainage, layout and calculation
ISO 8283-1:1991 Plastics pipes and fittings Dimensions of sockets and spigots for discharge systems inside buildings Part 1: Unplasticized poly(vinyl chloride) (PVC-U) and chlorinated poly (vinyl chloride) (PVC-C)
EN 1565-1:1998 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN+PVC) - Part 1: Specifications for pipes, fittings and the system
EN 12056-5:2000 Gravity drainage systems inside buildings - Part 5: Installation and testing, instructions for operation, maintenance and use

View more information
£276.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.