DEFSTAN 22-94/3(2011) : 2011

Foreword
1 Scope
2 Warning
3 Normative References
4 Abbreviations
5 Performance Specification
6 Military Standards/Requirements
7 Design Requirements/Guidance
8 Type Testing, Batch Testing and Inspection
9 Acceptance Standard
10 Corporate Experience & Knowledge
Annex A - Normative References
Annex B - Abbreviations
Annex C - Testing and Test Report Requirements for
          Type 1 Hose - 64 mm Bore for Abeam RAS for use
          with Portable Water
Annex D - Tensile and Elongation Test Equipment
          and Preparation for Type 1 Hose - 64 mm Bore
          Assembly for Abeam RAS for use with Portable Water
Annex E - Testing and Test Report Requirements for
          Type 2 Hose - 64 mm Bore for Abeam RAS for use
          with Lubricating Oils, Dieso Fuel and Avcat
Annex F - Tensile and Elongation Test Equipment and
          Preparation for Type 2 Hose - 64 mm Bore for RAS for
          use with Lubricating Oils, Dieso Fuel and Avcat
Annex G - Testing and Test Report Requirements for
          Type 3 Hose - 153 mm Bore for Abeam RAS for use
          with Dieso Fuel and Avcat
Annex H - Tensile and Elongation Test, Equipment
          and Preparation for Type 3 Hose - 153 mm Bore for
          Abeam RAS for use with Dieso Fuel and Avcat
Annex I - Testing and Test Report Requirements for
          Type 4 Hose - 153 mm Bore for Astern RAS for use
          with Dieso Fuel (Lay on Deck)
Annex J - Tensile and Elongation Test, Equipment
          and Preparation for Type 4 Hose - 153 mm Bore for
          Astern RAS for use with Dieso Fuel (Lay on Deck)
Annex K - Testing and Test Report Requirements
          for Type 5 Hose - 153 mm Bore Wire Reinforced
          Hardwall for use on the Probe Received and the
          Outboard Hose in the Abeam Rig in RAS for Dieso
          Fuel and Avcat
Annex L - Tensile and Elongation Test, Equipment
          and Preparation for Type 5 Hose - 153 mm Bore
          Wire Reinforced Hardwall for use on the Probe
          Received and the Outboard Hose in the Abeam
          Rig in RAS for Dieso Fuel and Avcat
Annex M - Testing and Test Report Requirements
          for Type 6 Hose - 153 mm Bore Softwall for use on
          the Probe Receiver in RAS for Dieso Fuel and Avcat
Annex N - Tensile and Elongation Test, Equipment
          and Preparation for Type 6 Hose - 153 mm Bore
          Softwall for use in the Probe Receiver in RAS for
          Dieso Fuel and Avcat
Annex O - Testing and Test Report Requirements
          for Type 7 Hose - 153 mm Bore Reelable Astern for
          RAS for use with Dieso Fuel
Annex P - Visible Defects in RAS Hoses
Annex Q - Hose Identification Panel
Annex R - Bend Test
Annex S - Low Temperature Flexibility Test
Annex T - Method of Measuring the Free Length of a Hose
Annex U - In-service Maintenance & Pressure Testing

Describes the details for the materials, manufacture, testing, packing and in-service maintenance of 64 mm bore and 153 mm bore reinforced synthetic rubber hoses and hose assemblies, for Replenishment at Sea (RAS).