DIN 17200:1987-03
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
STEELS FOR QUENCHING AND TEMPERING - TECHNICAL DELIVERY CONDITIONS
Published date
12-01-2013
Superseded date
01-10-1991
Sorry this product is not available in your region.
TRANSLATED INTO ENGLISH
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| ISO 6831:1986 | Similar to |
| EURONORM 83 : 1970 | Similar to |
| DIN 15400:1990-06 | LIFTING HOOKS - MATERIALS, MECHANICAL PROPERTIES, LIFTING CAPACITY AND STRESSES |
| DIN 7354:1978-08 | WOOD AND LEATHER MARKING PUNCHES |
| DIN 50150:2000-10 | TESTING OF METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES |
| DIN 59361:1981-10 | GRINDED AND POLISHED BRIGHT ROUND STEEL; DIMENSIONS, TOLERANCES ACCORDING TO ISO TOLERANCES ZONE H6 |
| DIN 65038-1:1989-08 | AEROSPACE; STEEL, NICKEL- AND COBALT-ALLOYS BARS; TECHNICAL SPECIFICATION |
| DIN 1016:1987-06 | STEEL FLAT PRODUCTS - HOT ROLLED SHEET AND STRIP - LIMIT DEVIATIONS, FORM AND MASS TOLERANCES |
| DIN 48065-1:1980-10 | BALL EYES WITHOUT PROTECTIVE FITTING ATTACHMENT, FOR U-SHAPED STRAPS, FOR OVERHEAD POWER LINES |
| DIN 740-1:1986-08 | POWER TRANSMISSION ENGINEERING; FLEXIBLE SHAFT COUPLINGS; TECHNICAL DELIVERY CONDITIONS |
| DIN 3761-7:1984-01 | ROTARY SHAFT LIP TYPE SEALS FOR AUTOMOBILES; TEST; SKITTLE MEASURING MANDREL |
| DIN 6916:1989-10 | ROUND WASHERS FOR HIGH-TENSILE STRUCTURAL BOLTING |
| DIN 43763:1986-03 | MEASUREMENT AND CONTROL - ELECTRICAL TEMPERATURE SENSORS - METAL PROTECTING TUBES FOR THERMOMETERS WITH INSERTED SENSOR UNITS |
| ISO 18265:2013 | Metallic materials — Conversion of hardness values |
| DIN 17240:1976-07 | HEAT RESISTING AND HIGHLY HEAT RESISTING MATERIALS FOR BOLTS AND NUTS - QUALITY SPECIFICATIONS |
| I.S. EN ISO 18265:2013 | METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES (ISO 18265:2013) |
| VDE 0210 : 1985 | PLANNING AND DESIGN OF OVERHEAD POWER LINES WITH RATED VOLTAGES ABOVE 1 KV |
| 11/30210148 DC : 0 | BS EN ISO 18265 - METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES |
| DIN 1651:1988-04 | FREE-CUTTING STEELS - TECHNICAL DELIVERY CONDITIONS |
| DIN EN 12812:2008-12 | FALSEWORK - PERFORMANCE REQUIREMENTS AND GENERAL DESIGN |
| DIN 50191:1987-09 | HARDENABILITY TEST BY END QUENCHING |
| VDE 0220-1 : 1971 | SPECIFICATION FOR DETACHABLE CABLE CLAMPS TO BE USED IN POWER CABLE INSTALLATIONS UP TO 1000 V |
| DIN 65299:1988-12 | AEROSPACE; UNIVERSAL JOINTS, NEEDLE BEARING SUPPORTED, LONG-TIME LUBRICATED, FOR ROTARY SHAFTS; DOUBLE JOINTS; CONNECTION DIMENSIONS, LOADS MASSES |
| DIN 4420-2:1990-12 | SERVICE AND WORKING SCAFFOLDS - LADDER SCAFFOLDS - SAFETY REQUIREMENTS |
| DIN 4112 : 1983 AMD 1 2006 | TEMPORARY STRUCTURES; CODE OF PRACTICE FOR DESIGN AND CONSTRUCTION |
| DIN VDE 0210 : 1985 | PLANNING AND DESIGN OF OVERHEAD POWER LINES WITH RATED VOLTAGES ABOVE 1 KV |
| DIN 17140-1:1983-03 | WIRE ROD FOR COLD DRAWING - TECHNICAL DELIVERY CONDITIONS FOR BASIC STEEL AND UNALLOYED QUALITY STEELS |
| DIN 1654-4:1989-10 | COLD HEADING AND COLD EXTRUDING STEELS - TECHNICAL DELIVERY CONDITIONS FOR STEELS FOR QUENCHING AND TEMPERING |
| DIN 15155:1986-12 | PALLETS - BOX PALLET WITH MESH SIDE PANELS AND 2 FRONTSIDE FLAPS |
| DIN 3990-5:1987-12 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; ENDURANCE LIMITS AND MATERIAL QUALITIES |
| DIN 17014-1:1988-08 | HEAT TREATMENT OF FERROUS MATERIALS - TERMINOLOGY |
| DIN EN ISO 18265:2014-02 | METALLIC MATERIALS - CONVERSION OF HARDNESS VALUES (ISO 18265:2013) |
| EN ISO 18265:2013 | Metallic materials - Conversion of hardness values (ISO 18265:2013) |
| DIN 8166:1992-03 | ROLLERS FOR CONVEYOR CHAINS WITH SOLID PINS, TYPE FV AND FVT; |
| DIN 3341:1989-07 | PLATE VALVES FOR DISPLACEMENT COMPRESSORS; SUCTION VALVES, DISCHARGE VALVES; MAIN DIMENSIONS, MATERIALS, INSTALLATION |
| DIN 59360:1981-10 | GROUND AND POLISHED BRIGHT ROUND STEEL; DIMENSIONS; PERMISSIBLE DEVIATIONS ACCORDING TO ISO TOLERANCE ZONE H7 |
| DIN 6918:1990-04 | SQUARE TAPER WASHERS FOR U-SECTIONS FOR HIGH-TENSILE STRUCTURAL BOLTING |
| DIN 6917:1989-10 | SQUARE TAPER WASHERS FOR I-SECTIONS FOR HIGH-TENSILE STRUCTURAL BOLTING |
| DIN 54452:1981-11 | TESTING OF ADHESIVES FOR METALS AND ADHESIVELY BONDED METAL JOINTS; COMPRESSION SHEAR TEST |
| DIN 65298:1988-12 | AEROSPACE; UNIVERSAL JOINTS, NEEDLE BEARING SUPPORTED, LONG-TIME LUBRICATED, FOR ROTARY SHAFTS; SINGLE JOINTS; CONNECTION DIMENSIONS, LOADS, MASSES |
| DIN 15063:1977-12 | LIFTING APPLIANCES; SHEAVES, TECHNICAL CONDITIONS |
| BS EN ISO 18265:2013 | Metallic materials. Conversion of hardness values |
| UNE-EN ISO 18265:2014 | Metallic materials - Conversion of hardness values (ISO 18265:2013) |
| DEFSTAN 01-8/1(1985) : 1985 | STEEL SPECIFICATIONS (GROUP SYSTEM) |
Summarise
Sorry this product is not available in your region.