DIN 267-11:1980-01
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
FASTENERS - TECHNICAL DELIVERY CONDITIONS (WITH ADDITIONS TO ISO 3506) - CORROSION-RESISTANT STAINLESS STEEL FASTENERS
Published date
12-01-2013
Superseded date
01-12-1992
Superseded by
Sorry this product is not available in your region.
1 Geltungsbereich
2 Verweis auf andere Normen
3 Bezeichnung, Kennzeichnung, Oberflächen-,
ausführung und magnetische Eigenschaften
4 Chemische Zusammensetzung der Werkstoffe
5 Mechanische Eigenschaften
6 Prüfverfahren
7 Hinweise für Anwender
Anhänge
A Chemische Zusammensetzung von rost- und
säurebeständigen Stählen (Auszug aus ISO 683/X11 I)
B Chemische Zusammensetzung von rost- und säurebeständigen
Stählen für Kaltumformung (Auszug aus ISO 4954)
C Schraubengewinde Spannungsquerschnitte entsprechend
ISO 898/l (siehe DIN ISO 898 Teil 1)
D Bruchdehnungswerte
| DocumentType |
Standard
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| SupersededBy |
| Standards | Relationship |
| ISO 3506:1979 | Similar to |
| DIN 964:1990-08 | SLOTTED RAISED COUNTERSUNK (OVAL) HEAD SCREWS |
| DIN 65523:1984-07 | Aerospace; hexagon bolts, with MJ-thread, short thread, corrosion-resisting steel, nominal tensile strength 700 MPa, for temperatures up to 425 C |
| DIN 28125-3:1989-04 | HINGED COVERS - CIRCULAR SHAPE WITH PROTECTION RING AND SURFACE COATED - DN 500 AND DN 600 |
| DIN 9021:1990-03 | WASHERS WITH OUTSIDE DIAMETER CA. 3 X NOMINAL THREAD DIAMETER |
| DIN 6922:1983-06 | HEXAGON FLANGE BOLTS WITH REDUCED SHANK |
| DIN 966:1990-08 | CROSS RECESSED RAISED COUNTERSUNK HEAD SCREWS |
| DIN 65370:1991-07 | Aerospace; sockets, eight- and fourteen-pole 5 Amp |
| DIN 7985:1990-08 | CROSS RECESSED RAISED CHEESE HEAD SCREWS |
| DIN 25202:1992-04 | RAILWAY VEHICLES - SECURING OF BOLTED JOINTS - INITIAL STRESSING FORCES AND TIGHTENING TORQUES |
| DIN 965:1990-08 | CROSS RECESSED COUNTERSUNK (FLAT) HEAD SCREWS |
| DIN 28125-1:1989-08 | DN 150 TO DN 600 ROUND HINGED CLOSURES |
| DIN 43673-1:1982-02 | DRILLED HOLES AND SCREW CONNECTIONS FOR BUSBARS; RECTANGULAR CROSS SECTION BUSBARS |
| DIN 28125-2:1989-04 | HINGED COVERS - ELLIPTICAL, 350 MM X 450 MM |
| DIN 915:1980-12 | HEXAGON SOCKET SET SCREWS WITH DOG POINT, ISO 4028 MODIFIED |
| DIN 914:1980-12 | HEXAGON SOCKET SET SCREWS WITH CONE POINT, ISO 4027 MODIFIED |
| DIN 125-2:1990-03 | PRODUCT GRADE A WASHERS WITH A HARDNESS FROM 300 HV, DESIGNED FOR USE WITH HEXAGON HEAD BOLTS AND NUTS |
| DIN 65522:1984-07 | AEROSPACE - SCREWS, HEXAGON, WITH MJ-THREAD, THREADED APPROXIMATELY TO HEAD, CORROSION-RESISTING STEEL, NOMINAL TENSILE STRENGTH 700 MPA, FOR TEMPERATURES UP TO 425 DEGREES C |
| DIN 975:1986-09 | THREADED RODS |
| DIN 25452:1992-04 | MECHANICAL DESIGN OF FUEL ELEMENT STORAGE POOL IN NUCLEAR POWER PLANTS WITH LIGHT-WATER REACTORS |
| DIN 57636-22 : 1984 | LOW-VOLTAGE FUSES - PART 22: H.R.C. FUSES; H.R.C. FUSES UP TO 1250 A AND 1000 V A.C. FOR PROTECTION OF EQUIPMENT |
| DIN 7991:1986-01 | HEXAGON SOCKET COUNTERSUNK HEAD CAP SCREWS |
| DIN 28125 Beiblatt 1:1989-04 | Hinged covers; example for construction of a lifting aid |
| DIN 125-1:1990-03 | PRODUCT GRADE A WASHERS WITH A HARDNESS UP TO 250 HV, DESIGNED FOR USE WITH HEXAGON HEAD BOLTS AND NUTS |
| DIN 963:1990-08 | SLOTTED COUNTERSUNK (FLAT) HEAD SCREWS |
| VDE 0636-22 : 1984 | LOW-VOLTAGE FUSES - PART 22: H.R.C. FUSES; H.R.C. FUSES UP TO 1250 A AND 1000 V A.C. FOR PROTECTION OF EQUIPMENT |
| DIN 427:1986-09 | SLOTTED HEADLESS SCREWS WITH CHAMFERED END |
| DIN 84:1990-08 | SLOTTED CHEESE HEAD SCREWS; PRODUCT GRADE A |
| DIN 85:1990-08 | SLOTTED PAN HEAD SCREWS; PRODUCT GRADE A |
| DIN 57636-21 : 1984 | LOW-VOLTAGE FUSES - PART 21: H.R.C. FUSES; PROTECTION OF CABLES AND CORDS UP TO 1250 A AND 500 V A.C., 440 V D.C. AND 660 V A.C. |
| DIN 65371:1992-06 | AEROSPACE; SOCKETS, FIVE- AND ELEVEN-POLE, 10 AMP |
| DIN VDE 0636-22 : 1984 | LOW-VOLTAGE FUSES - PART 22: H.R.C. FUSES - H.R.C. FUSES UP TO 1250 A AND 1000 V A.C. FOR PROTECTION OF EQUIPMENT |
| DIN 7337:1991-08 | BLIND RIVETS WITH BREAK MANDREL |
| DIN 3547-1:1990-06 | PN 4 TO PN 16 GAS AND WATER STOPVALVES; REQUIREMENTS AND ACCEPTANCE TESTING |
| DIN 65502:1984-07 | AEROSPACE - PAN HEAD BOLTS WITH RIPPED TORQ-SET (ACR) RECESS AND MJ-THREAD, SHORT THREAD, CORROSION-RESISTING STEEL, NOMINAL TENSILE STRENGTH 700 MPA, FOR TEMPERATURES UP TO 425 DEGREES C |
| DIN 48801:1985-03 | LIGHTNING PROTECTION SYSTEMS; CONDUCTORS, SCREWS AND NUTS |
| DIN 28129:1990-03 | Clamp nuts; for covers |
Summarise
Sorry this product is not available in your region.