DIN 3962-2:1978-08
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
TOLERANCES FOR CYLINDRICAL GEAR TEETH; TOLERANCES FOR TOOTH TRACE DEVIATIONS
Available format(s)
Hardcopy , PDF
Language(s)
English, German
Published date
01-01-1978
Superseded date
01-03-2018
£26.70
Excluding VAT
| DocumentType |
Standard
|
| Pages |
2
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Supersedes |
| DIN 21772:2012-07 | GEARS - CYLINDRICAL INVOLUTE GEARS AND GEAR PAIRS - DEFINITION OF DEVIATIONS |
| DIN 3960:1987-03 | DEFINITIONS, PARAMETERS AND EQUATIONS FOR INVOLUTE CYLINDRICAL GEARS AND GEAR PAIRS |
| DIN ISO 14635-2:2010-01 | Gears - FZG test procedures - Part 2: FZG step load test A10/16, 6R/120 for relative scuffing load-carrying capacity of high EP oils (ISO 14635-2:2004) |
| DIN 3990-21:1989-02 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; APPLICATION STANDARD FOR HIGH SPEED GEARS AND GEARS OF SIMILAR REQUIREMENT |
| DIN ISO 14635-3:2011-08 | Gears - FZG test procedures - Part 3: FZG test method A/2,8/50 for relative scuffing load-carrying capacity and wear characteristics of semifluid gear greases (ISO 14635-3:2005) |
| DIN ISO 14635-1:2006-05 | Gears - FZG test procedures - Part 1: FZG test method A/8,3/90 for relative scuffing load-carrying capacity of oils (ISO 14635-1:2000) |
| DIN HDBK 123 : 5ED 2007 | |
| DIN 3969-1:1991-10 | Surface roughness of tooth flanks; roughness parameters, surface grades |
| VDI/VDE 2613:2003-12 | Pitch and runout testing on gearings - Cylindrical gears, whormwheels, bevel gears |
| DIN 3990-41:1990-05 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; APPLICATION STANDARD FOR VEHICLE GEARS |
| DIN ISO 21771:2014-08 | Gears - Cylindrical involute gears and gear pairs - Concepts and geometry (ISO 21771:2007) |
| DIN 3990-11:1989-02 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; APPLICATION STANDARD FOR INDUSTRIAL GEARS; DETAILED METHOD |
| DIN 1829-2:1977-11 | Pinion-type cutters for cylindrical gears; tolerances |
| DIN 3990-5:1987-12 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS; ENDURANCE LIMITS AND MATERIAL QUALITIES |
| DIN 4000-59:1987-12 | TABULAR LAYOUTS OF ARTICLE CHARACTERISTICS FOR RACKS, CYLINDRICAL GEARS, PINION SHAFTS, BEVEL GEARS, BEVEL PINION SHAFTS, WORMS AND WORM WHEELS |
| DIN 3990-1:1987-12 | CALCULATION OF LOAD CAPACITY OF CYLINDRICAL GEARS - INTRODUCTION AND GENERAL INFLUENCE FACTORS |
| DIN ISO 18653:2009-12 | Gears - Evaluation of instruments for the measurement of individual gears (ISO 18653:2003) |
| DIN 3970:2010-04 | Master gears for checking cylindrical gears - Gear blanks and gearing |
Summarise
£26.70
Excluding VAT
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.