DIN EN 483:2000-06
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
GAS-FIRED CENTRAL HEATING BOILERS - TYPE C BOILERS OF NOMINAL HEAT INPUT NOT EXCEEDING 70 KW
Hardcopy , PDF
English
01-01-2000
01-01-2013
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification of boilers
5 Constructional requirements
6 Operational requirements
7 Test methods
8 Marking and instructions
Annex A (informative) - National situations
Annex B (informative) - Particular national conditions
Annex C (informative) - Classification of Type C boilers
Annex D (informative) - Composition of the gas circuit
Annex E (informative) - Compilation of the test conditions
Annex F (normative) - Test apparatus for Type C[2] boilers
Annex G (informative) - Practical method of calibrating the
test rig to enable the heat loss D[p] to be determined
Annex H (informative) - A-deviations
Annex J (informative) - Main symbols and abbreviations used
Annex K (informative) - Examples for marking
Annex L (informative) - Example of calculation of the
weighting factors for a boiler with several rates
following Table 17
Annex M (informative) - Calculation of conversions of NO[x]
Annex N (informative) - Requirements and test methods for
separate air supply and combustion products evacuation
ducts of Type C[6] boilers
Annex P (informative) - Determination of the heat loses from
the test rig of the indirect method and the
contribution of the circulating pump of the test rigs
Annex Q (informative) - Means of determining the ignition time at
full rate
Annex ZA (informative) - Clauses of this European standard
addressing essential requirements or other provisions
of EU Directives
Annex R (normative) - Test methods to determine the effects of
to long-term thermal load, long-term condensate exposure,
condensing/non-condensing cycling and resistance to
UV radiation
Annex S (informative) - Comparison table on clauses of this
amendment addressing essential requirements of the
GAD or other provisions of EU directives
Bibliography
| DevelopmentNote |
Supersedes DIN 3368-5 E and DIN 3368-6 E. (03/2003)
|
| DocumentType |
Standard
|
| Pages |
138
|
| PublisherName |
German Institute for Standardisation (Deutsches Institut für Normung)
|
| Status |
Superseded
|
| Standards | Relationship |
| NS EN 483 : 1999 AMD 4 2007 | Identical |
| BS EN 483 : 2000 | Identical |
| NF EN 483 : 2000 AMD 4 2008 | Identical |
| NEN EN 483 : 99 AMD 4 2007 | Identical |
| I.S. EN 483:2000 | Identical |
| NBN EN 483 : 1999 AMD 4 2008 | Identical |
| EN 1859:2009+A1:2013 | Chimneys - Metal chimneys - Test methods |
| EN ISO 1183-3:1999 | Plastics - Methods for determining the density of non-cellular plastics - Part 3: Gas pyknometer method (ISO 1183-3:1999) |
| EN ISO 8256:2004 | Plastics - Determination of tensile-impact strength (ISO 8256:2004) |
| EN 1856-2:2009 | Chimneys - Requirements for metal chimneys - Part 2: Metal flue liners and connecting flue pipes |
| EN ISO 527-2:2012 | Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012) |
| EN 13216-1:2004 | Chimneys - Test methods for system chimneys - Part 1: General test methods |
| ISO 188:2011 | Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests |
| ISO 8256:2004 | Plastics — Determination of tensile-impact strength |
| EN ISO 527-1:2012 | Plastics - Determination of tensile properties - Part 1: General principles (ISO 527-1:2012) |
| EN ISO 179-1:2010 | Plastics - Determination of Charpy impact properties - Part 1: Non-instrumented impact test (ISO 179-1:2010) |
| ISO 527-2:2012 | Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics |
| EN 14241-1:2013 | Chimneys - Elastomeric seals and elastomeric sealants - Material requirements and test methods - Part 1: Seals in flue liners |
| ISO 7619:1997 | Rubber — Determination of indentation hardness by means of pocket hardness meters |
| EN ISO 9969:2016 | Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016) |
| ISO 6914:2013 | Rubber, vulcanized or thermoplastic — Determination of ageing characteristics by measurement of stress relaxation in tension |
| EN 14471:2013+A1:2015 | Chimneys - System chimneys with plastic flue liners - Requirements and test methods |
| ISO 179-1:2010 | Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test |
| ISO 37:2017 | Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties |
| EN 1856-1:2009 | Chimneys - Requirements for metal chimneys - Part 1: System chimney products |
| ISO 178:2010 | Plastics — Determination of flexural properties |
| ISO 9969:2016 | Thermoplastics pipes — Determination of ring stiffness |
| EN 513:1999 | Unplasticized polyvinylchloride (PVC-U) profiles for the fabrication of windows and doors - Determination of the resistance to artificial weathering |
| EN ISO 1183-1:2012 | Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012) |
| ISO 527-1:2012 | Plastics — Determination of tensile properties — Part 1: General principles |
| ISO 1817:2015 | Rubber, vulcanized or thermoplastic — Determination of the effect of liquids |
| EN ISO 1183-2:2004 | Plastics - Methods for determining the density of non-cellular plastics - Part 2: Density gradient column method (ISO 1183-2:2004) |
| ISO 2781:2008 | Rubber, vulcanized or thermoplastic — Determination of density |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.