• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 1093-11:2001+A1:2008

Current
Current

The latest, up-to-date edition.

Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 11: Decontamination index
Published date

09-07-2008

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Principle
5 Determination of concentration measurement points
6 Test method
7 Application to specific group of machines
8 Influencing factors
9 Expression of results
10 Test report
Annex ZA (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 98/37/EC
Annex ZB (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 2006/42/EC

This standard describes a method for the measurement of the decontami¬nation index of pollution con¬trol systems e. g. capture devices including local exhaust ventilation, water spray systems and, when appropriate, separation equipment installed on a machine. This method uses the real pollutant (see 4.2 of EN 1093-1 : 1998 “ Safety of machinery — Evaluation of the emission of airborne hazardous substances — Part 1: Selection of test methods”) and can be operated in room or field environments.It should be observed that during the test, especially during the shutdown or the removal of the pollution control system, the concentration of hazardous substances , if present, can reach levels which are liable to incur a risk to the health of the operators or other occupants present in the room.Warning: This standard does not deal with the protective measures required to control these risks.Measurement of the decontamination index of pollution control system can serve for the:–evaluation of the performance of a pollution control system of a machine;–evaluation of the improvement of a pollution control system;–comparison of pollution control systems for machines of similar design;–ranking of pollution control systems according to their decontamination efficiency;–determination of the air flow rate in the case of an exhaust system to achieve a given level;–determination of the state of the art of pollution control systems for machines with respect to the decontamina¬tion efficiency.

Committee
CEN/TC 114
DevelopmentNote
2001 Edition Re-Issued in July 2008 & incorporates AMD 1 2008. (07/2008)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Current

I.S. EN 691-1:2012 SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS
12/30253910 DC : DRAFT JULY 2012 BS EN 1807-2 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - LOG SAWING MACHINES
PREN 1870-3 : DRAFT 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
11/30237569 DC : 0 BS EN 1870-19 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
DIN EN 1807-1:2013-06 Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
I.S. EN ISO 18217:2015 SAFETY OF WOODWORKING MACHINES - EDGE-BANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015)
PREN 1870-12 : DRAFT 2011 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES
I.S. EN 1807-2:2013 SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES
UNE-EN ISO 19085-1:2018 Woodworking machines - Safety - Part 1: Common requirements (ISO 19085-1:2017)
DIN EN 1870-7:2013-01 Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
DIN EN 1870-12:2014-03 Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines
DIN EN 1870-16:2013-01 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING
DIN EN 1870-9:2013-01 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
DIN EN 1870-3:2015-02 Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
I.S. EN 861:2007 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
UNE-EN 1870-4:2012 Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading
BS EN 859 : 2007 SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES
UNE-EN 1870-7:2013 Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
BS EN 1870-9:2012 Safety of woodworking machines. Circular sawing machines Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading
BS EN 1870-15:2012 Safety of woodworking machines. Circular sawing machines Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading
I.S. EN 1870-16:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V-CUTTING
EN 1807-1:2013 Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
EN 1093-1:2008 Safety of machinery - Evaluation of the emission of airborne hazardous substances - Part 1: Selection of test methods
15/30302620 DC : 0 BS EN ISO 19085-4 - WOODWORKING MACHINES - SAFETY - PART 4: VERTICAL PANEL CIRCULAR SAWING MACHINES
12/30265270 DC : 0 BS EN 1870-6 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING
11/30237566 DC : 0 BS EN 1870-18 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
07/30165769 DC : 0 BS EN 1093-1 - SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS
UNE-EN 1870-13:2008 Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines
BS EN 1870-19:2013 Safety of woodworking machines. Circular sawing machines Circular saw benches (with and without sliding table) and building site saws
UNI EN 1870-19 : 2014 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
11/30237557 DC : 0 BS EN 1870-11 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
DIN EN 1807-2:2013-06 Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines; German version EN 1807-2:2013
12/30232434 DC : 0 BS EN 1870-5:2002+A1:2009 AMD 2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
UNE-EN 691-1:2013 Safety of woodworking machines - Part 1: Common requirements
PREN 1870-11 : DRAFT 2011 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI-AUTOMATIC AND AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
11/30244804 DC : 0 BS EN 940:2009/A1 - SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
PREN 1870-6 : DRAFT 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING
DIN EN 1870-14:2012-06 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
DIN EN 1870-13:2013-07 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES
DIN EN 1870-10:2013-07 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
DIN EN 1870-8:2013-03 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
BS EN 1870-7:2012 Safety of woodworking machines. Circular sawing machines Single blade log sawing machines with integrated feed table and manual loading and/or unloading
BS EN 940 : 2009 SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
UNE-EN 1870-10:2013 Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
I.S. EN 1870-8:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
I.S. EN 1870-10:2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
I.S. EN 1870-11:2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
I.S. EN 1870-12:2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES
I.S. EN 1870-9:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSSCUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
I.S. EN 1870-3:2014 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
I.S. EN 1093-1:2008 SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS
I.S. EN 12750:2013 SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
I.S. EN 1870-15:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTIBLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING
I.S. EN 1870-17:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
I.S. EN 1870-14:2007 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
I.S. EN 940:2009 SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
I.S. EN 1870-5:2002 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
I.S. EN 1870-7:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 7: SINGLE BLADE LOG SAWING MACHINES WITH INTEGRATED FEED TABLE AND MANUAL LOADING AND/OR UNLOADING
I.S. EN 1870-4:2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
UNI EN 940 : 2012 SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
UNI EN 691-1 : 2012 SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS
I.S. EN 848-1:2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
DIN EN ISO 18217:2015-12 Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
11/30231787 DC : 0 BS EN 1870-14:2007+A1:2009/FPRA2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
10/30232428 DC : DRAFT DEC 2010 BS EN 1870-16 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING
BS EN 1870-18:2013 Safety of woodworking machines. Circular sawing machines Dimension saws
DIN EN 1870-19 E : 2014 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
12/30253907 DC : DRAFT JULY 2012 BS EN 1807-1 - SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - TABLE BAND SAWS AND BAND RE-SAWS
10/30233212 DC : 0 BS EN 848-3 - SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES
BS EN 1807-2:2013 Safety of woodworking machines. Band sawing machines Log sawing machines
10/30232431 DC : DRAFT DEC 2010 BS EN 1870-17 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (MANUAL RADIAL ARM SAWS)
14/30293310 DC : 0 BS EN ISO 19085-1 - WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS
BS EN 1807-1:2013 Safety of woodworking machines. Band sawing machines Table band saws and band re-saws
BS EN ISO 19085-1:2017 Woodworking machines. Safety Common requirements
11/30237563 DC : 0 BS EN 1870-10 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
UNE-EN 1807-1:2013 Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and band re-saws
UNI EN 1807-2 : 2013 SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 2: LOG SAWING MACHINES
PREN 1870-10 : DRAFT 2011 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
UNE-EN 1870-14:2008 Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines
EN ISO 19085-1:2017/AC:2018 WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS (ISO 19085-1:2017)
ISO/TR 18569:2004 Safety of machinery Guidelines for the understanding and use of safety of machinery standards
DIN EN 1870-11:2014-02 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
DIN EN 12750:2013-05 Safety of woodworking machines - Four sided moulding machines
DIN EN 1870-17:2015-06 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
DIN EN 1870-15:2013-01 Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading
DIN EN 848-3:2013-01 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES
DIN EN 860:2012-09 SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES
DIN EN 848-1:2013-01 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
DIN EN 848-2:2013-01 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
BS EN 861 : 2007 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
UNE-EN 1870-8:2013 Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
BS EN 848-2 : 2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
UNE-EN 848-1:2008 Safety of woodworking machines - One side moulding machines with rotating tool - Part 1: Single spindle vertical moulding machines
UNE-EN 848-3:2013 Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines
I.S. EN 848-2:2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
EN 1870-15:2012 Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading
UNI EN 1870-13 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES
UNI EN 1870-8 : 2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 8: SINGLE BLADE EDGING CIRCULAR RIP SAWING MACHINES WITH POWER DRIVEN SAW UNIT AND MANUAL LOADING AND/OR UNLOADING
UNI EN 1093-1 : 2009 SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS
UNI EN 1870-15 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTI-BLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING
UNI EN 12750 : 2013 SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
UNI EN 848-3 : 2012 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES
UNI EN 1870-16 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 16: DOUBLE MITRE SAWING MACHINES FOR V CUTTING
UNI EN 860 : 2012 SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANNING MACHINES
UNI EN 859 : 2012 SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES
UNI EN 848-1 : 2013 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
EN 1870-11:2013 Safety of woodworking machines - Circular sawing machines - Part 11: Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)
UNI EN 1870-9 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
UNI EN 1870-12 : 2014 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES
UNI EN 1870-14 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
UNI EN 1870-10 : 2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 10: SINGLE BLADE AUTOMATIC AND SEMI-AUTOMATIC UP-CUTTING CROSS-CUT SAWING MACHINES
UNI EN 1870-11 : 2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 11: SEMI AUTOMATIC HORIZONTAL CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
EN 860:2007+A2:2012 Safety of woodworking machines - One side thickness planing machines
UNI EN 1870-4 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
UNI EN 848-2 : 2013 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
UNI EN 861 : 2012 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
UNI EN 1870-5 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
UNI EN 1870-7:2012 Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
UNI EN 1807-1 : 2013 SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS
14/30293313 DC : 0 BS EN ISO 19085-2 - WOODWORKING MACHINES - SAFETY - PART 2: HORIZONTAL BEAM PANEL CIRCULAR SAWING MACHINES
10/30232425 DC : DRAFT DEC 2010 BS EN 1870-15 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 15: MULTI-BLADE CROSS-CUT SAWING MACHINES WITH INTEGRATED FEED OF THE WORKPIECE AND MANUAL LOADING AND/OR UNLOADING
10/30227080 DC : DRAFT JUNE 2010 BS EN 691-1 - SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS
DIN EN 1870-19:2014-03 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
I.S. EN 848-3:2012 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES
11/30237560 DC : 0 BS EN 1870-12 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 12: PENDULUM CROSS-CUT SAWING MACHINES
16/30318928 DC : 0 BS EN ISO 19085-7 - WOODWORKING MACHINES - SAFETY - PART 7: SURFACE PLANING THICKNESS PLANING COMBINED SURFACE/THICKNESS PLANING MACHINES
PREN 848-3 : DRAFT 2010 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOLS - PART 3: NUMERICALLY CONTROLLED (NC) BORING AND ROUTING MACHINES
12/30263881 DC : 0 BS EN 1870-3 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 3: DOWN CUTTING CROSS-CUT SAWS AND DUAL PURPOSE DOWN CUTTING CROSS-CUT SAWS/CIRCULAR SAW BENCHES
11/30231784 DC : 0 BS EN 1870-13:2007+A1:2009/FPRA2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES
16/30335973 DC : 0 BS ISO 19085-9 - WOODWORKING MACHINES - SAFETY - PART 9: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE)
14/30297793 DC : 0 BS EN ISO 19085-3 - WOODWORKING MACHINES - SAFETY REQUIREMENTS - PART 3: NC BORING AND ROUTING MACHINES
DIN EN 1870-18:2013-08 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
UNI EN 1870-18 : 2014 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
UNE-EN 1807-2:2013 Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines
I.S. EN 1870-18:2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 18: DIMENSION SAWS
DIN EN 940:2012-05 SAFETY OF WOODWORKING MACHINES - COMBINED WOODWORKING MACHINES
DIN EN 861:2012-09 SAFETY OF WOODWORKING MACHINES - SURFACE PLANING AND THICKNESSING MACHINES
DIN EN 859:2012-09 SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANING MACHINES
DIN EN 1093-1:2009-02 SAFETY OF MACHINERY - EVALUATION OF THE EMISSION OF AIRBORNE HAZARDOUS SUBSTANCES - PART 1: SELECTION OF TEST METHODS
BS EN 1093-1:2008 Safety of machinery. Evaluation of the emission of airborne hazardous substances Selection of test methods
BS EN 1870-12:2013 Safety of woodworking machines. Circular sawing machines Pendulum cross-cut sawing machines
BS EN 848-1 : 2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 1: SINGLE SPINDLE VERTICAL MOULDING MACHINES
UNE-EN 1870-15:2013 Safety of woodworking machines - Circular sawing machines - Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading
BS EN 1870-3:2014 Safety of woodworking machines. Circular sawing machines Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
UNE-EN 12750:2013 Safety of woodworking machines - Four sided moulding machines
BS EN 12750:2013 Safety of woodworking machines. Four sided moulding machines
BS EN 1870-11:2013 Safety of woodworking machines. Circular sawing machines Semi automatic horizontal cross-cut sawing machines with one saw unit (radial arm saws)
BS EN 1870-4:2012 Safety of woodworking machines. Circular sawing machines Multiblade rip sawing machines with manual loading and/or unloading
ISO 18217:2015 Safety of woodworking machines Edge-banding machines fed by chain(s)
UNE-EN 860:2007 Safety of woodworking machines - One side thickness planing machines
BS EN 1870-13 : 2007 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES
UNE-EN 1870-9:2013 Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading
UNE-EN 1870-16:2013 Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting
BS EN 1870-5 : 2002 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAW BENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
BS EN 860 : 2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES
EN 691-1:2012 Safety of woodworking machines - Part 1: Common requirements
EN 1870-16:2012 Safety of woodworking machines - Circular sawing machines - Part 16: Double mitre sawing machines for V cutting
EN 1870-13:2007+A2:2012 Safety of woodworking machines - Circular sawing machines - Part 13: Horizontal beam panel sawing machines
EN 1870-6:2017 Safety of woodworking machines - Circular sawing machines - Part 6: Circular sawing machines for fire wood
EN 1870-3:2014 Safety of woodworking machines - Circular sawing machines - Part 3: Down cutting cross-cut saws and dual purpose down cutting cross-cut saws/circular saw benches
EN 1870-18:2013 Safety of woodworking machines - Circular sawing machines - Part 18: Dimension saws
EN 1870-14:2007+A2:2012 Safety of woodworking machines - Circular sawing machines - Part 14: Vertical panel sawing machines
EN 1807-2:2013 Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines
EN 1870-7:2012 Safety of woodworking machines - Circular sawing machines - Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading
EN 1870-5 : 2002 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 5: CIRCULAR SAWBENCHES/UP-CUTTING CROSS-CUT SAWING MACHINES
EN 1870-19:2013 Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws
EN 1870-17:2012+A1:2015 Safety of woodworking machines - Circular sawing machines - Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (radial arm saws)
EN 859:2007+A2:2012 Safety of woodworking machines - Hand fed surface planing machines
EN 861:2007+A2:2012 Safety of woodworking machines - Surface planing and thicknessing machines
EN 848-2 : 2007 COR 2012 SAFETY OF WOODWORKING MACHINES - ONE SIDE MOULDING MACHINES WITH ROTATING TOOL - PART 2: SINGLE SPINDLE HAND FED/INTEGRATED FED ROUTING MACHINES
EN 940:2009+A1:2012 Safety of woodworking machines - Combined woodworking machines
EN 1870-8:2012 Safety of woodworking machines - Circular sawing machines - Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
EN 1870-4:2012 Safety of woodworking machines - Circular sawing machines - Part 4: Multiblade rip sawing machines with manual loading and/or unloading
EN 848-3:2012 Safety of woodworking machines - One side moulding machines with rotating tool - Part 3: Numerically controlled (NC) boring and routing machines
EN 1870-12:2013 Safety of woodworking machines - Circular sawing machines - Part 12: Pendulum cross-cut sawing machines
EN 1870-10:2013 Safety of woodworking machines - Circular sawing machines - Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
EN 1870-9:2012 Safety of woodworking machines - Circular sawing machines - Part 9: Double blade circular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading
ISO 19085-1:2017 Woodworking machines Safety Part 1: Common requirements
BS EN 691-1:2012 Safety of woodworking machines Common requirements
DIN EN 691-1:2013-01 SAFETY OF WOODWORKING MACHINES - PART 1: COMMON REQUIREMENTS
11/30232437 DC : 0 BS EN 1870-6:2002+A1:2009/FPRA2 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 6: CIRCULAR SAWING MACHINES FOR FIREWOOD AND DUAL PURPOSE CIRCULAR SAWING MACHINES FOR FIREWOOD/CIRCULAR SAW BENCHES, WITH MANUAL LOADING AND/OR UNLOADING
16/30318924 DC : 0 BS EN ISO 19085-6 - WOODWORKING MACHINES - SAFETY - PART 6: SINGLE SPINDLE VERTICAL MOULDING MACHINES ('TOUPIES')
DIN EN ISO 18217 E : 2015 SAFETY OF WOODWORKING MACHINES - EDGEBANDING MACHINES FED BY CHAIN(S) (ISO 18217:2015)
I.S. EN 1870-13:2007 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 13: HORIZONTAL BEAM PANEL SAWING MACHINES
16/30341470 DC : 0 BS EN ISO 19085-10 - WOODWORKING MACHINES - SAFETY - PART 10: BUILDING SITE SAWS (CONTRACTOR SAWS)
BS EN ISO 18217:2015 Safety of woodworking machines. Edge-banding machines fed by chain(s)
12/30260496 DC : 0 BS EN 12750 - SAFETY OF WOODWORKING MACHINES - FOUR SIDED MOULDING MACHINES
15/30300474 DC : DRAFT FEB 2015 BS ISO 19085-5 - WOODWORKING MACHINES - SAFETY - PART 5: DIMENSION SAWS
10/30232422 DC : DRAFT DEC 2010 BS EN 1870-9 - SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 9: DOUBLE BLADE CIRCULAR SAWING MACHINES FOR CROSS-CUTTING WITH INTEGRATED FEED AND WITH MANUAL LOADING AND/OR UNLOADING
BS EN 1870-6:2017 Safety of woodworking machines. Circular sawing machines Circular sawing machines for fire wood
UNE-EN 1870-18:2013 Safety of woodworking machines - Circular sawing machines - Part 18: Dimension saws
16/30331355 DC : 0 BS EN ISO 19085-8 - WOODWORKING MACHINES - SAFETY - PART 8: WIDE BELT CALIBRATING AND SANDING MACHINES
UNE-EN ISO 18217:2016 Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
I.S. EN 1807-1:2013 SAFETY OF WOODWORKING MACHINES - BAND SAWING MACHINES - PART 1: TABLE BAND SAWS AND BAND RE-SAWS
I.S. EN ISO 19085-1:2017 WOODWORKING MACHINES - SAFETY - PART 1: COMMON REQUIREMENTS (ISO 19085-1:2017)
I.S. EN 1870-19:2013 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 19: CIRCULAR SAW BENCHES (WITH AND WITHOUT SLIDING TABLE) AND BUILDING SITE SAWS
EN ISO 18217:2015 Safety of woodworking machines - Edge-banding machines fed by chain(s) (ISO 18217:2015)
DIN EN 1870-4:2012-06 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 4: MULTIBLADE RIP SAWING MACHINES WITH MANUAL LOADING AND/OR UNLOADING
DIN EN 1870-5:2013-01 Safety of woodworking machines - Circular sawing machines - Part 5: Circular saw benches/up-cutting cross-cut sawing machines (includes Amendment A2:2012)
BS EN 1870-8:2012 Safety of woodworking machines. Circular sawing machines Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading
PD ISO/TR 18569:2004 Safety of machinery. Guidelines for the understanding and use of safety of machinery standards.
BS EN 1870-16:2012 Safety of woodworking machines. Circular sawing machines Double mitre sawing machines for V cutting
BS EN 848-3:2012 Safety of woodworking machines. One side moulding machines with rotating tool Numerically controlled (NC) boring and routing machines
I.S. EN 859:2007 SAFETY OF WOODWORKING MACHINES - HAND FED SURFACE PLANNING MACHINES
I.S. EN 860:2007 SAFETY OF WOODWORKING MACHINES - ONE SIDE THICKNESS PLANING MACHINES
BS EN 1870-14 : 2007 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 14: VERTICAL PANEL SAWING MACHINES
BS EN 1870-17 : 2012 SAFETY OF WOODWORKING MACHINES - CIRCULAR SAWING MACHINES - PART 17: MANUAL HORIZONTAL CUTTING CROSS-CUT SAWING MACHINES WITH ONE SAW UNIT (RADIAL ARM SAWS)
BS EN 1870-10:2013 Safety of woodworking machines. Circular sawing machines Single blade automatic and semi-automatic up-cutting cross-cut sawing machines
EN 12750:2013 Safety of woodworking machines - Four sided moulding machines

ISO 7145:1982 Determination of flowrate of fluids in closed conduits of circular cross-section Method of velocity measurement at one point of the cross-section
ISO 4053-1:1977 Measurement of gas flow in conduits — Tracer methods — Part 1: General
ISO/TR 5168:1998 Measurement of fluid flow Evaluation of uncertainties
ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
1998/37/EC : 1998 DIRECTIVE 98/37/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL OF 22 JUNE 1998 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES RELATING TO MACHINERY
ISO 3966:2008 Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes
EN 1070 : 1998 SAFETY OF MACHINERY - TERMINOLOGY
ISO 4006:1991 Measurement of fluid flow in closed conduits — Vocabulary and symbols

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.