• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 13463-1:2009

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Non-electrical equipment for use in potentially explosive atmospheres - Part 1: Basic method and requirements
Superseded date

01-04-2016

Published date

21-01-2009

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Equipment categories and explosion groups
5 Ignition hazard assessment
6 Assessment of possible ignition sources
7 Additional considerations
8 Verification and tests
9 Documentation and information for use
Annex A (normative) Methodology for confirming the category
Annex B (informative) Explanation of the ignition hazard
        assessment procedure
Annex C (informative) Examples of ignition hazard assessment
Annex D (informative) Charging tests with non conductive materials
Annex E (informative) Example of rig for resistance to impact test
Annex F (normative) Rig for impact ignition test
Annex G (informative) Consideration of misuse which can
        reasonably be anticipated during ignition hazard
        assessment procedure
Annex H (informative) Significant changes between this
        European Standard and the previous edition
Annex ZA (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 94/9/EC
Bibliography

This European Standard specifies the basic method and requirements for design, construction, testing and marking of non-electrical equipment intended for use in potentially explosive atmospheres in air of gas, vapour, mist and dusts. Such atmospheres can also exist inside the equipment. In addition, the external atmosphere can be drawn inside the equipment by natural breathing produced as a result of fluctuations in the equipment’s internal operating pressure, and/or temperature.This European Standard is valid for atmospheres having pressures ranging from 0,8 bar to 1,1 bar and temperatures ranging from - 20 °C to + 60 °C., i.e. equipment built to this European Standard will be satisfactory to any service conditions within this range unless otherwise specified.NOTE 1The requirements of this European Standard can also be helpful for the design, construction, testing and marking of equipment intended for use in atmospheres outside the validity range stated above. In this case however, the ignition hazard assessment, ignition protection provided, additional testing (if necessary), manufacturer’s technical documentation and instructions to the user, should clearly demonstrate and indicate the equipment’s suitability for the conditions it may encounter. It should also be recognized that changes in temperature and pressure can have a significant influence on ignitability.This European Standard does not cover additional marking for equipment intended for use outside the scope of its validity such as an oxygen-enriched atmosphere.This European Standard is also applicable for the design, construction, testing and marking of components, protective systems, devices and assemblies of these products which have possible ignition sources and are intended for use in potentially explosive atmospheres.

Committee
CEN/TC 305
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

I.S. EN 16125:2015 LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG IN LIQUID PHASE AND VAPOUR PRESSURE PHASE
API 685 REDLINE : 2011 SEALLESS CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL, AND GAS INDUSTRY PROCESS SERVICE
14/30301257 DC : 0 BS EN 13160-3 - LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS
BS EN 15089:2009 Explosion isolation systems
DIN EN ISO 11148-6:2013-05 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 6: ASSEMBLY POWER TOOLS FOR THREADED FASTENERS (ISO 11148-6:2012)
10/30219414 DC : 0 BS EN 13617-4 - PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS
BS EN ISO 11148-1:2011 Hand-held non-electric power tools. Safety requirements Assembly power tools for non-threaded mechanical fasteners
UNI EN ISO 11148-2 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 2: CUTTING-OFF AND CRIMPING POWER TOOLS
PREN 50050-1 : DRAFT 2011 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
BS EN ISO 11148-11:2011 Hand-held non-electric power tools. Safety requirements Nibblers and shears
03/107320 DC : DRAFT APR 2003 EN 14678-1 - LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS
12/30265289 DC : 0 BS EN 12050-1 - WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER
UNI EN 1474-1 : 2009 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS
03/119040 DC : DRAFT NOV 2003 PREN 1010-1 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS
11/30248849 DC : 0 BS EN 50050-3:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
UNE-EN 50050-2:2014 Electrostatic hand-held spraying equipment - Safety requirements - Part 2: Hand-held spraying equipment for ignitable coating powder
13/30279579 DC : 0 BS ISO 19372 - MICROTURBINES APPLICATIONS - SAFETY
12/30243081 DC : 0 BS EN 1034-17 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
09/30198043 DC : 0 BS EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
UNI EN 13237 : 2012 POTENTIALLY EXPLOSIVE ATMOSPHERES - TERMS AND DEFINITIONS FOR EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
DIN EN ISO 11148-5:2012-06 Hand-held non-electric power tools - Safety requirements - Part 5: Rotary percussive drills (ISO 11148-5:2011)
13/30273033 DC : 0 BS EN 1012-3 - COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS
BS EN ISO 11148-10:2011 Hand-held non-electric power tools. Safety requirements Compression power tools
ISO 13578:2017 Industrial furnaces and associated processing equipment — Safety requirements for machinery and equipment for production of steel by electric arc furnaces
I.S. EN 15089:2009 EXPLOSION ISOLATION SYSTEMS
11/30239006 DC : 0 BS EN 13237 - POTENTIALLY EXPLOSIVE ATMOSPHERES - TERMS AND DEFINITIONS FOR EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
10/30227668 DC : 0 BS EN 14678-3 - LPG EQUIPMENT AND ACCESSORIES - PART 3: REFUELLING INSTALLATIONS AT PRIVATE AND INDUSTRIAL PREMISES
12/30270980 DC : 0 BS EN 1127-2 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING
10/30227671 DC : 0 BS EN 14678-1 - LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS
BS EN 14677:2008 Safety of machinery. Secondary steelmaking. Machinery and equipment for treatment of liquid steel
09/30202029 DC : 0 BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES
04/30115503 DC : DRAFT JUN 2004 EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
08/30173506 DC : DRAFT JAN 2008 BS EN 1539 - DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS
I.S. EN 14678-3:2013 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES
I.S. EN ISO 11148-1:2011 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 1: ASSEMBLY POWER TOOLS FOR NON-THREADED MECHANICAL FASTENERS (ISO 11148-1:2011)
I.S. EN 50176:2009 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
I.S. EN 415-10:2014 SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS
PREN 13012 : DRAFT 2010 PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS
I.S. EN ISO 11148-10:2011 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS (ISO 11148-10:2011)
I.S. EN ISO 11148-8:2011 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 8: SANDERS AND POLISHERS (ISO 11148-8:2011)
I.S. EN 1474-1:2008 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS
I.S. EN 16009:2011 FLAMELESS EXPLOSION VENTING DEVICES
PD CLC/TR 60079-32-1:2015 Explosive atmospheres Electrostatic hazards, guidance
I.S. EN ISO 11148-3:2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 3: DRILLS AND TAPPERS (ISO 11148-3:2012)
UNE-EN 15089:2010 Explosion isolation systems
I.S. EN 14973:2015 CONVEYOR BELTS FOR USE IN UNDERGROUND INSTALLATIONS - ELECTRICAL AND FLAMMABILITY SAFETY REQUIREMENTS
UNE-EN 50050-3:2014 Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock
PREN 16770 : DRAFT 2014 SAFETY OF WOODWORKING MACHINES - CHIP AND DUST EXTRACTION SYSTEMS FOR INDOOR INSTALLATION - SAFETY REQUIREMENTS
EN 13617-1:2012 Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
DIN EN 1804-3:2010-05 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems (includes Amendment A1:2010)
DIN EN 13463-2:2005-02 NON-ELECTRICAL EQUIPMENT FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 2: PROTECTION BY FLOW RESTRICTING ENCLOSURE 'FR'
DIN EN 13355:2010-06 COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
EN 13617-4:2012 Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
DIN EN 14678-2:2012-04 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 2: Components other than dispensers and installation requirements (includes Amendment A1:2012)
BS EN 1755:2015 Industrial Trucks. Safety requirements and verification. Supplementary requirements for operation in potentially explosive atmospheres
UNE-EN 13617-2:2012 Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
UNE-EN 13617-4:2012 Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
UNE-EN 1127-1:2012 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
BS EN 14678-2 : 2007 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS
BS EN 14797:2006 Explosion venting devices
BS EN 13617-3:2012 Petrol filling stations Safety requirements for construction and performance of shear valves
BS EN 13463-3:2005 Non-electrical equipment for use in potentially explosive atmospheres Protection by flameproof enclosure \'d\'
BS EN 13760:2003 Automotive LPG filling system for light and heavy duty vehicles. Nozzle, test requirements and dimensions
DIN EN 1127-2:2002-07 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING
I.S. EN 14678-2:2007 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS
EN 12753:2005+A1:2010 Thermal cleaning systems for exhaust gas from surface treatment equipment - Safety requirements
EN 1034-17:2012 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines
CLC/TR 60079-33:2015 Explosive atmospheres - Part 33: Equipment protection by special protection 's'
DIN EN 14797:2007-03 Explosion venting devices
EN 13463-6:2005 Non-electrical equipment for use in potentially explosive atmospheres - Part 6: Protection by control of ignition source 'b'
EN 1010-1:2004+A1:2010 Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements
EN 12050-1:2015 Wastewater lifting plants for buildings and sites - Part 1: Lifting plants for wastewater containing faecal matter
EN 50176:2009 Stationary electrostatic application equipment for ignitable liquid coating material - Safety requirements
EN 13237:2012 Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
EN 50177:2009/A1:2012 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS
I.S. EN 13760:2003 AUTOMOTIVE LPG FILLING SYSTEM FOR LIGHT AND HEAVY DUTY VEHICLES - NOZZLE, TEST REQUIREMENTS AND DIMENSIONS
EN 12779:2015 Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements
EN 13463-3:2005 Non-electrical equipment for use in potentially explosive atmospheres - Part 3: Protection by flameproof enclosure 'd'
EN 12621:2006+A1:2010 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
EN 14591-2:2007/AC:2008 EXPLOSION PREVENTION AND PROTECTION IN UNDERGROUND MINES - PROTECTIVE SYSTEMS - PART 2: PASSIVE WATER TROUGH BARRIERS
EN 12215:2004+A1:2009 Coating plants - Spray booths for application of organic liquid coating materials - Safety requirements
EN 12693:2008 Refrigerating systems and heat pumps - Safety and environmental requirements - Positive displacement refrigerant compressors
EN 12757-1:2005+A1:2010 Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing
EN 13463-8:2003 Non-electrical equipment for potentially explosive atmospheres - Part 8: Protection by liquid immersion 'k'
EN 13463-2:2004 Non-electrical equipment for use in potentially explosive atmospheres - Part 2: Protection by flow restricting enclosure 'fr'
EN 13355:2004+A1:2009 Coating plants - Combined booths - Safety requirements
EN 50050-3:2013 Electrostatic hand-held spraying equipment - Safety requirements - Part 3: Hand-held spraying equipment for ignitable flock
EN 12186:2014 Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
DIN EN 14492-2:2010-05 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
11/30246684 DC : 0 BS EN 1953 - ATOMISING AND SPRAYING EQUIPMENT FOR COATING MATERIALS - SAFETY REQUIREMENTS
DIN EN 14678-3:2013-03 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES
API 11D3 :2008 PROGRESSING CAVITY PUMP SYSTEMS FOR ARTIFICIAL LIFT - SURFACE-DRIVE SYSTEMS
06/30150265 DC : 0 EN 1474-1 - INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS
13/30280729 DC : 0 BS EN 12186 - GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS
UNI EN ISO 8230-3 : 2009 SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 3: MACHINES USING COMBUSTIBLE SOLVENTS
11/30247811 DC : 0 BS EN 415-10 - SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS
UNI EN ISO 11148-1 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 1: ASSEMBLY POWER TOOLS FOR NON-THREADED MECHANICAL FASTENERS
I.S. EN 13463-5:2011 NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
BS EN ISO 11148-12:2012 Hand-held non-electric power tools. Safety requirements Circular, oscillating and reciprocating saws
ISO 21789:2009 Gas turbine applications — Safety
11/30248842 DC : 0 BS EN 50050-1:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
I.S. EN 13463-6:2005 NON-ELECTRICAL EQUIPMENT FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 6: PROTECTION BY CONTROL OF IGNITION SOURCE 'B'
PREN 1672-1 : DRAFT 2012 FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS
08/30183842 DC : DRAFT JUNE 2008 BS EN ISO 11148-6 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 6: ASSEMBLY POWER TOOLS FOR THREADED FASTENERS
08/30183838 DC : DRAFT JUNE 2008 BS EN ISO 11148-4 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 4: NON-ROTARY PERCUSSIVE POWER TOOLS
DIN EN 12693:2016-10 (Draft) REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
BS EN ISO/IEC 80079-34:2011 Explosive atmospheres Application of quality systems for equipment manufacture
08/30180312 DC : DRAFT MAR 2008 BS EN 50223 - STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
PREN 14973 : DRAFT 2013 CONVEYOR BELTS FOR USE IN UNDERGROUND INSTALLATIONS - ELECTRICAL AND FLAMMABILITY SAFETY REQUIREMENTS
CLC/TR 50404:2003 Electrostatics - Code of practice for the avoidance of hazards due to static electricity
12/30259421 DC : 0 BS EN 1672-1 - FOOD PROCESSING MACHINERY - BASIC CONCEPTS - PART 1: SAFETY REQUIREMENTS
14/30301251 DC : 0 BS EN 13160-1 - LEAK DETECTION SYSTEMS - PART 1: GENERAL PRINCIPLES
02/540765 DC : DRAFT SEP 2002 BS EN 13463-3 - NON-ELECTRICAL EQUIPMENT FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 3: PROTECTION BY FLAMEPROOF ENCLOSURE 'D'
09/30187383 DC : 0 BS ISO 11148-11 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS
05/30125032 DC : DRAFT JUL 2005 EN 14678-2 - LPG EQUIPMENT AND ACCESSORIES - EQUIPMENT FOR LIQUEFIED PETROLEUM GAS AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS, AND INSTALLATION REQUIREMENTS
12/30249552 DC : DRAFT JULY 2012 BS EN 1755 A2 - SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST
API 685 : 2011 SEALLESS CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL, AND GAS INDUSTRY PROCESS SERVICE
BS EN 14678-3:2013 LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Refuelling installations at commercial and industrial premises
12/30243465 DC : 0 BS ISO/IEC 80079-38 - EXPLOSIVE ATMOSPHERES - PART 38: EQUIPMENT AND COMPONENTS IN EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
10/30230365 DC : 0 BS EN 50050-2 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
BS EN ISO 11148-5:2011 Hand-held non-electric power tools. Safety requirements Rotary percussive drills
11/30235009 DC : 0 BS EN 13852-1 - CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES
PREN 1953 : DRAFT 2011 ATOMISING AND SPRAYING EQUIPMENT FOR COATING MATERIALS - SAFETY REQUIREMENTS
UNI EN ISO 11148-5 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 5: ROTARY PERCUSSIVE DRILLS
DIN EN ISO 11148-11:2012-06 Hand-held non-electric power tools - Safety requirements - Part 11: Nibblers and shears (ISO 11148-11:2011)
UNI EN ISO 11148-6 : 2013 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 6: ASSEMBLY POWER TOOLS FOR THREADED FASTENERS
BS EN 50223:2015 Stationary electrostatic application equipment for ignitable flock material. Safety requirements
BS EN 15268:2008 Petrol filling stations. Safety requirements for the construction of submersible pump assemblies
13/30286132 DC : 0 BS EN 13616-2 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - REQUIREMENTS AND TEST/ASSESSMENT METHODS - PART 2: OVERFILL PREVENTION DEVICES WITHOUT CLOSURE DEVICE
09/30187371 DC : 0 BS ISO 11148-1 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 1: ASSEMBLY POWER TOOLS FOR NON-THREADED MECHANICAL FASTENERS
CEI EN 50176 : 2010 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
S.R. CEN/TR 16829:2016 FIRE AND EXPLOSION PREVENTION AND PROTECTION FOR BUCKET ELEVATORS
05/30127970 DC : DRAFT JAN 2005 EN 1127-1 - EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
BS EN 12693:2008 Refrigerating systems and heat pumps. Safety and environmental requirements. Positive displacement refrigerant compressors
PREN 12186 : DRAFT 2013 GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS
S.R. CLC/TR 60079-32-1:2015 EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS - GUIDANCE
UNI EN 16009 : 2011 FLAMELESS EXPLOSION VENTING DEVICES
PREN 14986 : DRAFT 2014 DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
DIN EN ISO 11148-8:2012-06 Hand-held non-electric power tools - Safety requirements - Part 8: Sanders and polishers (ISO 11148-8:2011)
PREN 1539 : DRAFT 2012 DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS
NF EN 50303 : 2000 GROUP I, CATEGORY M1 EQUIPMENT INTENDED TO REMAIN FUNCTIONAL IN ATMOSPHERES ENDANGERED BY FIREDAMP AND/OR COAL DUST
I.S. EN 1127-1:2011 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
I.S. EN 1012-3:2013 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS
I.S. EN ISO/IEC 80079-34:2011 EXPLOSIVE ATMOSPHERES - PART 34: APPLICATION OF QUALITY SYSTEMS FOR EQUIPMENT MANUFACTURE
UNI EN 15268 : 2009 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
I.S. EN 50177:2009 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS
UNE-EN 14678-2:2009 LPG equipment and accessories - Equipment for Liquefied Petroleum Gas automotive filling stations - Part 2: Components other than dispensers, and installation requirements
EN 13012:2012 Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
NF EN 1127-1 : 2011 EXPLOSIVES ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
I.S. EN 14591-4:2007 EXPLOSION PREVENTION AND PROTECTION IN UNDERGROUND MINES - PROTECTIVE SYSTEMS - PART 4: AUTOMATIC EXTINGUISHING SYSTEMS FOR ROAD HEADERS
NF EN 1804-2 : 2002 + A1 2010 MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 2: POWER SET LEGS AND RAMS
I.S. EN 15268:2008 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
I.S. EN 14492-2:2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
DIN EN 1010-1:2011-06 Safety of machinery - Safety requirements for the design and construction of printing and paper converting machines - Part 1: Common requirements (includes Amendment A1:2010)
DIN EN 12215:2010-06 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
DIN EN 12621:2011-07 Machinery for the supply and circulation of coating materials under pressure - Safety requirements (includes Amendment A1:2010)
DIN EN 1012-1:2011-02 Compressors and vacuum pumps - Safety requirements - Part 1: Air compressors
DIN EN 12581:2011-02 Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements (includes Amendment A1:2010)
DIN EN 12981:2010-06 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
DIN EN 13617-4:2012-05 Petrol filling stations - Part 4: Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
DIN EN 13617-3:2012-05 Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves
DIN EN 13617-1:2012-08 Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
DIN EN 14681:2010-10 Safety of machinery - Safety requirements for machinery and equipment for production of steel by electric arc furnaces (includes Amendment A1:2010)
DIN EN 15198 E : 2007 METHODOLOGY FOR THE RISK ASSESSMENT OF NON-ELECTRICAL EQUIPMENT AND COMPONENTS FOR INTENDED USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
BS EN ISO 13709:2003 Centrifugal pumps for petroleum, petrochemical and natural gas industries
BS EN 13355 : 2004 COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
UNE-EN 12186:2015 Gas infrastructure - Gas pressure regulating stations for transmission and distribution - Functional requirements
BS EN 12757-1 : 2005 MIXING MACHINERY FOR COATING MATERIALS - SAFETY REQUIREMENTS - PART 1: MIXING MACHINERY FOR USE IN VEHICLE REFINISHING
BS EN 12981 : 2005 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
I.S. EN 14492-1:2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
I.S. EN 14678-1:2013 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS
I.S. EN 1012-1:2010 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 1: AIR COMPRESSORS
UNI EN 1804-3 : 2010 MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 3: HYDRAULIC CONTROL SYSTEMS
I.S. EN 1804-3:2006 MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 3: HYDRAULIC CONTROL SYSTEMS
DIN EN 1755:2016-02 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
I.S. EN 13237:2012 POTENTIALLY EXPLOSIVE ATMOSPHERES - TERMS AND DEFINITIONS FOR EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
I.S. EN 13012:2012 PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS
I.S. EN 12757-1:2005 MIXING MACHINERY FOR COATING MATERIALS - SAFETY REQUIREMENTS - PART 1: MIXING MACHINERY FOR USE IN VEHICLE REFINISHING
I.S. EN 12215:2004 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
I.S. EN 13617-4:2012 PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS
DIN EN 1127-1:2011-10 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
DIN EN 1776:2016-05 GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
DIN EN 14492-1:2010-06 Cranes - Power driven winches and hoists - Part 1: Power driven winches (includes Amendment A1:2009)
DIN EN 13463-5:2011-10 NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
I.S. EN 1127-2:2014 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING
DIN EN 13463-5:2004-03 NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
I.S. EN 13852-1:2013 CRANES - OFFSHORE CRANES - PART 1: GENERAL - PURPOSE OFFSHORE CRANES
I.S. EN 12981:2005 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
I.S. EN 12921-3:2005 MACHINES FOR SURFACE CLEANING AND PRE-TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 3: SAFETY OF MACHINES USING FLAMMABLE CLEANING LIQUIDS
I.S. EN 12621:2006 MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS
DIN EN 13463-8:2004-01 NON-ELECTRICAL EQUIPMENT FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 8: PROTECTION BY LIQUID IMMERSION 'K'
DIN EN 13852-2:2005-03 Cranes - Offshore cranes - Part 2: Floating cranes
I.S. EN 14681:2006 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
I.S. EN 1539:2015 DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS
I.S. EN 1755:2015 INDUSTRIAL TRUCKS - SAFETY REQUIREMENTS AND VERIFICATION - SUPPLEMENTARY REQUIREMENTS FOR OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES
I.S. EN 13355:2005 COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
I.S. EN 13617-2:2012 PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS
I.S. EN 12186:2014 GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS
DIN EN 1539:2016-02 DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS
I.S. EN 12779:2015 SAFETY OF WOODWORKING MACHINES - CHIP AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATION - SAFETY RELATED PERFORMANCES AND SAFETY REQUIREMENTS
I.S. EN 13617-1:2012 PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS
I.S. EN 14125:2013 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
I.S. EN 1010-1:2005 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS
EN 1804-3:2006+A1:2010 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems
DIN EN 13760:2003-11 Automotive LPG filling system for light and heavy duty vehicles - Nozzle; Test requirements and dimensions
I.S. EN 12753:2005 THERMAL CLEANING SYSTEMS FOR EXHAUST GAS FROM SURFACE TREATMENT EQUIPMENT - SAFETY REQUIREMENTS
I.S. EN 1776:2015 GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
DIN EN 13463-6:2005-07 NON-ELECTRICAL EQUIPMENT FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 6: PROTECTION BY CONTROL OF IGNITION SOURCE 'B'
I.S. EN 1953:2013 ATOMISING AND SPRAYING EQUIPMENT FOR COATING MATERIALS - SAFETY REQUIREMENTS
I.S. EN 12050-1:2015 WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER
I.S. EN 13617-3:2012 PETROL FILLING STATIONS - PART 3: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SHEAR VALVES
I.S. EN 12581:2006 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
VDI 2263 Blatt 5:2014-10 Dust fires and dust explosions - Hazards, assessment, protective measures - Explosion protection in fluidized bed dryers
VDI/VDE 3844:2014-01 Industrial process control valves - Actuators for control valves
VDI 2263 Blatt 8.1:2011-03 Dust fires and dust explosions - Hazards - assessment - protective measures - Fire and explosion protection on elevators - Examples
VDI 2262 Blatt 1:2013-06 Workplace air - Reduction of exposure to air pollutants - Legal principles, terms and definitions, basic organisational measures for industrial safety and environmental protection
VDI 2263 Blatt 6:2017-08 Dust fires and dust explosions - Hazards - assessment - protective measures - Dust fires and explosion protection in dust extracting installations
VDI 3476 Blatt 2:2010-01 Waste gas cleaning - Catalytic waste gas cleaning methods - Oxidative processes
CEI EN 50050-2 : 2014 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
DIN EN ISO 11148-2:2012-06 Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools (ISO 11148-2:2011)
PREN 50223 : DRAFT 2013 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
10/30219402 DC : 0 BS EN 13012 - PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS
09/30199364 DC : 0 BS EN 13463-5 - NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
13/30284894 DC : 0 BS EN 50223 - STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
BS EN ISO 11148-2:2011 Hand-held non-electric power tools. Safety requirements Cutting-off and crimping power tools
13/30257895 DC : 0 BS EN 1755 - SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST
PD CEN/CLC/TR 16832:2015 Selection, use, care and maintenance of personal protective equipment for preventing electrostatic risks in hazardous areas (explosion risks)
UNI EN 12693 : 2008 REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
BS EN 50050-2:2013 Electrostatic hand-held spraying equipment. Safety requirements Hand-held spraying equipment for ignitable coating powder
PREN 13617-1 : DRAFT 2010 PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS
DIN EN ISO 11148-12:2013-05 Hand-held non-electric power tools - Safety requirements - Part 12: Circular, oscillating and reciprocating saws (ISO 11148-12:2012)
09/30183551 DC : 0 BS ISO 11148-7 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS
08/30183566 DC : DRAFT JUNE 2008 BS ISO 11148-3 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 3: DRILLS AND TAPPERS
BS PD CEN/TR 16832 : 2015 SELECTION, USE, CARE AND MAINTENANCE OF PERSONAL PROTECTIVE EQUIPMENT FOR PREVENTING ELECTROSTATIC RISKS IN HAZARDOUS AREAS (EXPLOSION RISKS)
09/30175678 DC : 0 BS EN 14681:2006/A1 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
S.R. CLC/TR 60079-33:2015 EXPLOSIVE ATMOSPHERES - PART 33: EQUIPMENT PROTECTION BY SPECIAL PROTECTION 'S'
DIN EN 15089:2009-07 EXPLOSION ISOLATION SYSTEMS
DIN EN 14677:2008-11 SAFETY OF MACHINERY - SECONDARY STEEL MAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL
15/30312749 DC : 0 BS EN 16808 - PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - SAFETY OF MACHINERIES - MANUAL ELEVATORS
PREN 14492-1 : DRAFT 2015 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
12/30258755 DC : 0 BS EN 1539 - DRYERS AND OVENS, IN WHICH FLAMMABLE SUBSTANCES ARE RELEASED - SAFETY REQUIREMENTS
06/30157092 DC : 0 ISO/DIS 21789 - GAS TURBINE APPLICATIONS - SAFETY
UNI EN ISO 11148-12 : 2013 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 12: CIRCULAR, OSCILLATING AND RECIPROCATING SAWS
DIN EN ISO/IEC 80079-34:2012-03 EXPLOSIVE ATMOSPHERES - PART 34: APPLICATION OF QUALITY SYSTEMS FOR EQUIPMENT MANUFACTURE (ISO/IEC 80079-34:2011)
10/30219405 DC : 0 BS EN 13617-1 - PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS
BS EN 1034-17:2012 Safety of machinery. Safety requirements for the design and construction of paper making and finishing machines Tissue making machines
CEI EN 50050-1 : 2014 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
DIN EN ISO 11148-3:2013-05 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 3: DRILLS AND TAPPERS (ISO 11148-3:2012)
BS EN 50050-3:2013 Electrostatic hand-held spraying equipment. Safety requirements Hand-held spraying equipment for ignitable flock
UNE-EN 50176:2010 Stationary electrostatic application equipment for ignitable liquid coating material - Safety requirements
DIN EN 15268 E : 2008 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP ASSEMBLIES
09/30183557 DC : 0 BS EN ISO 11148-9 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 9: DIE GRINDERS
UNI EN ISO 11148-8 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 8: SANDERS AND POLISHERS
DIN EN 14973 E : 2016 CONVEYOR BELTS FOR USE IN UNDERGROUND INSTALLATIONS - ELECTRICAL AND FLAMMABILITY SAFETY REQUIREMENTS
03/118986 DC : DRAFT NOV 2003 EN 14797 - EXPLOSION VENTING DEVICES
BS EN 1012-3:2013 Compressors and vacuum pumps. Safety requirements Process compressors
DIN EN ISO 8230-3:2009-05 SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 3: MACHINES USING COMBUSTIBLE SOLVENTS
14/30294092 DC : 0 BS EN 14986 - DESIGN OF FANS WORKING IN POTENTIALLY EXPLOSIVE ATMOSPHERES
UNI EN 15089 : 2009 EXPLOSION ISOLATION SYSTEMS
BS ISO 21789:2009 Gas turbine applications — Safety
05/30131803 DC : DRAFT APR 2005 EN 15198 - METHODOLOGY FOR THE IGNITION HAZARD ASSESSMENT OF NON-ELECTRICAL EQUIPMENT AND COMPONENTS FOR INTENDED USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
DIN EN 415-10:2014-07 SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS
BS EN 14973:2015 Conveyor belts for use in underground installations. Electrical and flammability safety requirements
PREN 13617-3 : DRAFT 2010 PETROL FILLING STATIONS - PART 3: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SHEAR VALVES
PREN 12779 : DRAFT 2014 SAFETY OF WOODWORKING MACHINES - CHIPS AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATIONS - SAFETY REQUIREMENTS
S.R. CEN/CLC/TR 16832:2015&LC:2015 SELECTION, USE, CARE AND MAINTENANCE OF PERSONAL PROTECTIVE EQUIPMENT FOR PREVENTING ELECTROSTATIC RISKS IN HAZARDOUS AREAS (EXPLOSION RISKS)
I.S. EN 50050-2:2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
UNI EN ISO 11148-4 : 2013 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 4: NON-ROTARY PERCUSSIVE POWER TOOLS
I.S. EN ISO 11148-12:2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 12: CIRCULAR, OSCILLATING AND RECIPROCATING SAWS (ISO 11148-12:2012)
UNI EN 415-10 : 2014 SAFETY OF PACKAGING MACHINES - PART 10: GENERAL REQUIREMENTS
CEN/CLC/TR 16832:2015 Selection, use, care and maintenance of personal protective equipment for preventing electrostatic risks in hazardous areas (explosion risks)
I.S. EN ISO 11148-6:2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 6: ASSEMBLY POWER TOOLS FOR THREADED FASTENERS (ISO 11148-6:2012)
PREN 13160-1 : DRAFT 2014 LEAK DETECTION SYSTEMS - PART 1: GENERAL PRINCIPLES
UNE-EN ISO/IEC 80079-34:2012 Explosive atmospheres - Part 34: Application of quality systems for equipment manufacture
UNI EN 14678-3 : 2013 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 3: REFUELLING INSTALLATIONS AT COMMERCIAL AND INDUSTRIAL PREMISES
IEC 60079-33:2012 Explosive atmospheres - Part 33: Equipment protection by special protection 's'
PREN 16985 : DRAFT 2016 SPRAY BOOTHS FOR ORGANIC COATING MATERIAL - SAFETY REQUIREMENTS
ISO 19372:2015 Microturbines applications — Safety
EN 13617-3:2012 Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves
DIN EN 1710:2008-08 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
EEMUA 186 : 2016 A PRACTITIONER'S HANDBOOK FOR POTENTIALLY EXPLOSIVE ATMOSPHERES
DIN EN 13463-3:2005-07 NON-ELECTRICAL EQUIPMENT FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 3: PROTECTION BY FLAMEPROOF ENCLOSURE 'D'
DIN EN 1953:2013-12 ATOMISING AND SPRAYING EQUIPMENT FOR COATING MATERIALS - SAFETY REQUIREMENTS
DIN EN 13617-2:2012-05 Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
DIN EN 1127-2:2014-09 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING
DIN EN 12186:2014-12 GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS
DIN EN 12779:2016-03 Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements
DIN EN 12050-1:2015-05 WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER
BS EN 13617-4:2012 Petrol filling stations Safety requirements for construction and performance of swivels for use on metering pumps and dispensers
BS EN 14591-2:2007 Explosion prevention and protection in underground mines. Protective systems Passive water trough barriers
UNE-EN 1755:2016 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
BS EN 13012:2012 Petrol filling stations. Construction and performance of automatic nozzles for use on fuel dispensers
UNE-EN 13617-3:2012 Petrol filling stations - Part 3: Safety requirements for construction and performance of shear valves
UNE-EN 14973:2016 Conveyor belts for use in underground installations - Electrical and flammability safety requirements
BS EN 1010-1 : 2004 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS
BS EN 12921-3 : 2005 MACHINES FOR SURFACE CLEANING AND PRE-TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 3: SAFETY OF MACHINES USING FLAMMABLE CLEANING LIQUIDS
BS EN 12215 : 2004 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
UNE-EN 14678-1:2013 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers
ISO 11148-4:2012 Hand-held non-electric power tools — Safety requirements — Part 4: Non-rotary percussive power tools
DIN EN 15198:2007-11 Methodology for the risk assessment of non-electrical equipment and components for intended use in potentially explosive atmospheres
BS EN 12753 : 2005 THERMAL CLEANING SYSTEMS FOR EXHAUST GAS FROM SURFACE TREATMENT EQUIPMENT - SAFETY REQUIREMENTS
BS EN 1539:2015 Dryers and ovens, in which flammable substances are released. Safety requirements
I.S. EN 13463-2:2005 NON-ELECTRICAL EQUIPMENT FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 2: PROTECTION BY FLOW RESTRICTING ENCLOSURE 'FR'
I.S. EN 13463-3:2005 NON-ELECTRICAL EQUIPMENT FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 3: PROTECTION BY FLAMEPROOF ENCLOSURE 'D'
UNE-EN 13463-5:2013 Non-electrical equipment intended for use in potentially explosive atmospheres - Part 5: Protection by constructional safety 'c'
UNE-EN 16125:2016 LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase
EN 1474-1:2008 Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms
UNI EN 13617-1 : 2012 PETROL FILLING STATIONS - PART 1: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF METERING PUMPS, DISPENSERS AND REMOTE PUMPING UNITS
EN 14678-1:2013 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers
UNI EN 14677 : 2008 SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL
UNI EN 1012-1 : 2010 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 1: AIR COMPRESSORS
UNI EN 12581 : 2010 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
UNI EN 1010-1 : 2011 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PRINTING AND PAPER CONVERTING MACHINES - PART 1: COMMON REQUIREMENTS
UNI EN 12186 : 2014 GAS INFRASTRUCTURE - GAS PRESSURE REGULATING STATIONS FOR TRANSMISSION AND DISTRIBUTION - FUNCTIONAL REQUIREMENTS
UNI EN 12981 : 2009 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC POWDER COATING MATERIAL - SAFETY REQUIREMENTS
UNI EN 13463-5 : 2011 NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
UNI EN 1012-3 : 2014 COMPRESSORS AND VACUUM PUMPS - SAFETY REQUIREMENTS - PART 3: PROCESS COMPRESSORS
UNI EN 12757-1 : 2010 MIXING MACHINERY FOR COATING MATERIALS - SAFETY REQUIREMENTS - PART 1: MIXING MACHINERY FOR USE IN VEHICLE REFINISHING
UNI EN 14591-1 : 2005 EXPLOSION PREVENTION AND PROTECTION IN UNDERGROUND MINES - PROTECTIVE SYSTEMS - PART 1: 2-BAR EXPLOSION PROOF VENTILATION STRUCTURE
UNI EN 1953 : 2013 Atomising and spraying equipment for coating materials - Safety requirements
UNI EN 13852-1 : 2013 CRANES - OFFSHORE CRANES - PART 1: GENERAL-PURPOSE OFFSHORE CRANES
UNI EN 1127-2 : 2014 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING
UNI EN 14591-4 : 2008 EXPLOSION PREVENTION AND PROTECTION IN UNDERGROUND MINES - PROTECTIVE SYSTEMS - PART 4: AUTOMATIC EXTINGUISHING SYSTEMS FOR ROAD HEADERS
UNI EN 14125 : 2013 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
UNI EN 12753 : 2010 THERMAL CLEANING SYSTEMS FOR EXHAUST GAS FROM SURFACE TREATMENT EQUIPMENT - SAFETY REQUIREMENTS
UNI EN 12621 : 2010 MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS
UNI EN 14492-2 : 2009 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
UNI EN 14678-2 : 2012 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 2: COMPONENTS OTHER THAN DISPENSERS AND INSTALLATION REQUIREMENTS
UNI EN 1710 : 2008 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
UNI EN 14678-1 : 2013 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS
UNI EN 13355 : 2009 COATING PLANTS - COMBINED BOOTHS - SAFETY REQUIREMENTS
UNI EN 12215 : 2010 COATING PLANTS - SPRAY BOOTHS FOR APPLICATION OF ORGANIC LIQUID COATING MATERIALS - SAFETY REQUIREMENTS
UNI EN 14492-1 : 2009 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
UNI EN 12921-3 : 2009 MACHINES FOR SURFACE CLEANING AND PRE- TREATMENT OF INDUSTRIAL ITEMS USING LIQUIDS OR VAPOURS - PART 3: SAFETY OF MACHINES USING FLAMMABLE CLEANING LIQUIDS
UNI EN 14681 : 2010 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
UNE-EN 50223:2016 Stationary electrostatic application equipment for ignitable flock material - Safety requirements
BS EN 50176:2009 Stationary electrostatic application equipment for ignitable liquid coating material. Safety requirements
09/30183554 DC : 0 BS EN ISO 11148-8 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 8: SANDERS AND POLISHERS
DIN EN 1474-1:2009-03 INSTALLATION AND EQUIPMENT FOR LIQUEFIED NATURAL GAS - DESIGN AND TESTING OF MARINE TRANSFER SYSTEMS - PART 1: DESIGN AND TESTING OF TRANSFER ARMS
DIN EN ISO 11148-1:2012-06 Hand-held non-electric power tools - Safety requirements - Part 1: Assembly power tools for non-threaded mechanical fasteners (ISO 11148-1:2011)
BS EN ISO 11148-8:2011 Hand-held non-electric power tools. Safety requirements Sanders and polishers
10/30214970 DC : 0 BS EN 13616 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID PETROLEUM FUELS
11/30231856 DC : 0 BS EN 14125 - THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
I.S. EN 13463-8:2003 NON-ELECTRICAL EQUIPMENT FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 8: PROTECTION BY LIQUID IMMERSION 'K'
PREN 14678-1 : DRAFT 2010 LPG EQUIPMENT AND ACCESSORIES - CONSTRUCTION AND PERFORMANCE OF LPG EQUIPMENT FOR AUTOMOTIVE FILLING STATIONS - PART 1: DISPENSERS
PREN 50050-3 : DRAFT 2011 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
UNI EN 1034-17 : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
PREN 50050-2 : DRAFT 2011 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
DIN EN 14973:2016-02 CONVEYOR BELTS FOR USE IN UNDERGROUND INSTALLATIONS - ELECTRICAL AND FLAMMABILITY SAFETY REQUIREMENTS
PREN 14125 : DRAFT 2011 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
BS EN ISO 11148-6:2012 Hand-held non-electric power tools. Safety requirements Assembly power tools for threaded fasteners
03/300200 DC : DRAFT JAN 2003 CENELEC TR 50404 - ELECTROSTATICS - CODE OF PRACTICE FOR THE AVOIDANCE OF HAZARDS DUE TO STATIC ELECTRICITY
09/30187374 DC : 0 BS ISO 11148-2 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 2: CUTTING-OFF AND CRIMPING POWER TOOLS
13/30286135 DC : 0 BS EN 13616-1 - OVERFILL PREVENTION DEVICES FOR STATIC TANKS FOR LIQUID FUELS - REQUIREMENTS AND TEST/ASSESSMENT METHODS - PART 1: OVERFILL PREVENTION DEVICES WITH CLOSURE DEVICE
10/30219408 DC : 0 BS EN 13617-2 - PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS
09/30208493 DC : 0 BS EN 16009 - FLAMELESS EXPLOSION VENTING DEVICES (TYPE C STANDARD)
CEN/TR 16832 : 2015 COR 2015 SELECTION, USE, CARE AND MAINTENANCE OF PERSONAL PROTECTIVE EQUIPMENT FOR PREVENTING ELECTROSTATIC RISKS IN HAZARDOUS AREAS (EXPLOSION RISKS)
11/30248845 DC : 0 BS EN 50050-2:2011 - ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
02/540766 DC : DRAFT SEP 2002 BS EN 13463-6 - NON-ELECTRICAL EQUIPMENT FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 6: PROTECTION BY CONTROL OF IGNITION SOURCE 'B'
BS EN 415-10:2014 Safety of packaging machines General Requirements
PREN 1755 : DRAFT 2013 SAFETY OF INDUSTRIAL TRUCKS - OPERATION IN POTENTIALLY EXPLOSIVE ATMOSPHERES - USE IN FLAMMABLE GAS, VAPOUR, MIST AND DUST
BS EN 1474-1:2008 Installation and equipment for liquefied natural gas. Design and testing of marine transfer systems Design and testing of transfer arms
10/30219411 DC : 0 BS EN 13617-3 - PETROL FILLING STATIONS - PART 3: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SHEAR VALVES
DIN EN 1034-17 E : 2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
04/30105027 DC : DRAFT JUNE 2004 ISO 21789 - GAS TURBINES - SAFETY
BS EN ISO 11148-7:2012 Hand-held non-electric power tools. Safety requirements Grinders
DIN EN 1034-17:2012-11 Safety of machinery - Safety requirements for the design and construction of paper making and finishing machines - Part 17: Tissue making machines
DIN EN 15268:2008-11 PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION OF SUBMERSIBLE PUMP
09/30187380 DC : 0 BS ISO 11148-10 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS
04/19986707 DC : 0 BS EN 1804-4 - MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 4: ELECTRO-HYDRAULIC CONTROL SYSTEMS
DIN EN 15089 E : 2009 EXPLOSION ISOLATION SYSTEMS
API 11D3 : 2008 : R2015 PROGRESSING CAVITY PUMP SYSTEMS FOR ARTIFICIAL LIFT - SURFACE-DRIVE SYSTEMS
DIN EN 16125:2016-03 LPG EQUIPMENT AND ACCESSORIES - PIPEWORK SYSTEMS AND SUPPORTS - LPG LIQUID PHASE AND VAPOUR PRESSURE PHASE
BS EN 50177 : 2009 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE COATING POWDERS - SAFETY REQUIREMENTS
DIN EN 14591-4:2007-09 Explosion prevention and protection in underground mines - Protective systems - Part 4: Automatic extinguishing systems for road headers
DIN EN ISO 11148-10:2012-06 Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools (ISO 11148-10:2011)
UNI EN 1127-1 : 2011 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 1: BASIC CONCEPTS AND METHODOLOGY
API 610 : 2010 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
PREN 13617-2 : DRAFT 2010 PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS
API 610 REDLINE : 2010 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
UNI EN ISO 11148-11 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS
I.S. EN 12693:2008 REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
BS PD IEC TS 60079-32-1 : 2013 EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS, GUIDANCE
CEI UNI EN ISO/IEC 80079-34 : 2013 EXPLOSIVE ATMOSPHERES - PART 34: APPLICATION OF QUALITY SYSTEMS FOR EQUIPMENT MANUFACTURE
UNI EN ISO 11148-3 : 2013 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 3: DRILLS AND TAPPERS
BS EN 16125:2015 LPG Equipment and Accessories. Pipework systems and supports. LPG in liquid phase and vapour pressure phase
PREN 13852-1 : DRAFT 2011 CRANES - OFFSHORE CRANES - PART 1: GENERAL PURPOSE OFFSHORE CRANES
PREN 12050-1 : DRAFT 2012 WASTEWATER LIFTING PLANTS FOR BUILDINGS AND SITES - PART 1: LIFTING PLANTS FOR WASTEWATER CONTAINING FAECAL MATTER
I.S. CLC/TR 50404:2006 ELECTROSTATICS - CODE OF PRACTICE FOR THE AVOIDANCE OF HAZARDS DUE TO STATIC ELECTRICITY
14/30301874 DC : 0 BS EN 16770 - SAFETY OF WOODWORKING MACHINES - CHIP AND DUST EXTRACTION SYSTEMS FOR INDOOR INSTALLATION - SAFETY REQUIREMENTS
16/30335146 DC : 0 BS EN 16985 - SPRAY BOOTHS FOR ORGANIC COATING MATERIAL - SAFETY REQUIREMENTS
UNE-EN 50050-1:2014 Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials
DIN EN 12753:2011-02 Thermal cleaning systems for exhaust gas from surface treatment equipment - Safety requirements (includes Amendment A1:2010)
DIN EN 12757-1:2011-02 Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing (includes Amendment A1:2010)
EN 13617-2:2012 Petrol filling stations - Part 2: Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
I.S. EN ISO 13709:2009 CENTRIFUGAL PUMPS FOR PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES
NF EN 1804-1 : 2002 + A1 2010 MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 1: SUPPORT UNITS AND GENERAL REQUIREMENTS
DIN EN 13012:2012-09 Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
DIN EN 14681 E : 2010 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
DIN EN 14797 E : 2007 EXPLOSION VENTING DEVICES
DIN EN 13852-1:2014-01 Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
BS EN 13463-5:2011 Non-electrical equipment intended for use in potentially explosive atmospheres Protection by constructional safety \'c\'
BS EN 12050-1:2015 Wastewater lifting plants for buildings and sites Lifting plants for wastewater containing faecal matter
ISO 11148-6:2012 Hand-held non-electric power tools — Safety requirements — Part 6: Assembly power tools for threaded fasteners
UNE-EN 12621:2006 Machinery for the supply and circulation of coating materials under pressure - Safety requirements
ISO 11148-1:2011 Hand-held non-electric power tools Safety requirements Part 1: Assembly power tools for non-threaded mechanical fasteners
ISO 8230-3:2008 Safety requirements for dry-cleaning machines Part 3: Machines using combustible solvents
BS EN 1804-3 : 2006 MACHINES FOR UNDERGROUND MINES - SAFETY REQUIREMENTS FOR HYDRAULIC POWERED ROOF SUPPORTS - PART 3: HYDRAULIC CONTROL SYSTEMS
BS EN 13463-6:2005 Non-electrical equipment for potentially explosive atmospheres Protection by control of ignition source \'b\'
BS EN 12186:2014 Gas infrastructure. Gas pressure regulating stations for transmission and distribution. Functional requirements
ISO/IEC 80079-34:2011 Explosive atmospheres Part 34: Application of quality systems for equipment manufacture
UNE-EN 1776:2017 Gas infrastructure - Gas measuring systems - Functional requirements
BS EN 13617-1:2012 Petrol filling stations Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
BS EN ISO 15136-2:2006 Petroleum and natural gas industries. Progressing cavity pump systems for artificial lift Surface drive systems
BS EN 12621 : 2006 MACHINERY FOR THE SUPPLY AND CIRCULATION OF COATING MATERIALS UNDER PRESSURE - SAFETY REQUIREMENTS
BS EN 12779:2015 Safety of woodworking machines. Chip and dust extraction systems with fixed installation. Safety requirements
BS EN 1776:2015 Gas infrastructure. Gas measuring systems. Functional requirements
UNE-EN 1539:2010 Dryers and ovens, in which flammable substances are released - Safety requirements
ISO 11148-2:2011 Hand-held non-electric power tools Safety requirements Part 2: Cutting-off and crimping power tools
EN ISO/IEC 80079-34:2011 Explosive atmospheres - Part 34: Application of quality systems for equipment manufacture (ISO/IEC 80079-34:2011)
BS ISO 19372:2015 Microturbines applications. Safety
ISO 11148-8:2011 Hand-held non-electric power tools Safety requirements Part 8: Sanders and polishers
ISO 15136-2:2006 Petroleum and natural gas industries — Progressing cavity pump systems for artificial lift — Part 2: Surface-drive systems
BS EN 13237:2012 Potentially explosive atmospheres. Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
ISO 11148-11:2011 Hand-held non-electric power tools Safety requirements Part 11: Nibblers and shears
BS EN 1127-2:2014 Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology for mining
UNE-EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
UNE-EN 13012:2012 Petrol filling stations - Construction and performance of automatic nozzles for use on fuel dispensers
BS EN 14492-1 : 2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
UNE-EN 13617-1:2012 Petrol filling stations - Part 1: Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
ISO 11148-5:2011 Hand-held non-electric power tools Safety requirements Part 5: Rotary percussive drills
BS EN 13463-8:2003 Non-electrical equipment for potentially explosive atmospheres Protection by liquid immersion \'k\'
BS EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
PD CLC/TR 60079-33:2015 Explosive atmospheres Equipment protection by special protection \'s\'
BS EN 1710 : 2005 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
ISO 11148-7:2012 Hand-held non-electric power tools — Safety requirements — Part 7: Grinders
ISO 11148-10:2011 Hand-held non-electric power tools Safety requirements Part 10: Compression power tools
BS IEC 60079-33 : 2012 EXPLOSIVE ATMOSPHERES - PART 33: EQUIPMENT PROTECTION BY SPECIAL PROTECTION 'S'
UNE-EN 12050-1:2015 Wastewater lifting plants for buildings and sites - Part 1: Lifting plants for wastewater containing faecal matter
UNE-EN 13852-1:2014 Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
EN 50223:2015 Stationary electrostatic application equipment for ignitable flock material - Safety requirements
EN ISO 11148-8:2011 Hand-held non-electric power tools - Safety requirements - Part 8: Sanders and polishers (ISO 11148-8:2011)
UNI EN 13617-4 : 2012 PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS
UNI EN 13617-2 : 2012 PETROL FILLING STATIONS - PART 2: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SAFE BREAKS FOR USE ON METERING PUMPS AND DISPENSERS
EN 1710:2005+A1:2008/AC:2010 EQUIPMENT AND COMPONENTS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES IN UNDERGROUND MINES
EI MODEL CODE SAFE PRACTICE PT1 : 2010 THE SELECTION, INSTALLATION, INSPECTION, AND MAINTENANCE OF ELECTRICAL AND NON ELECTRICAL APPARATUS IN HAZARDOUS AREAS
EN 415-10:2014 Safety of packaging machines - Part 10: General Requirements
EN ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries (ISO 13709:2009)
UNI EN 13012 : 2012 PETROL FILLING STATIONS - CONSTRUCTION AND PERFORMANCE OF AUTOMATIC NOZZLES FOR USE ON FUEL DISPENSERS
EN 1755:2015 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
UNI EN 13617-3 : 2012 PETROL FILLING STATIONS - PART 3: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SHEAR VALVES
EN ISO 8230-3:2008 Safety requirements for dry-cleaning machines - Part 3: Machines using combustible solvents (ISO 8230-3:2008)
EN ISO 11148-7:2012 Hand-held non-electric power tools - Safety requirements - Part 7: Grinders (ISO 11148-7:2012)
EN 15198:2007 Methodology for the risk assessment of non-electrical equipment and components for intended use in potentially explosive atmospheres
EN 14797:2006 Explosion venting devices
EN ISO 11148-6:2012 Hand-held non-electric power tools - Safety requirements - Part 6: Assembly power tools for threaded fasteners (ISO 11148-6:2012)
EN ISO 11148-4:2012 Hand-held non-electric power tools - Safety requirements - Part 4: Non-rotary percussive power tools (ISO 11148-4:2012)
EN ISO 11148-12:2012 Hand-held non-electric power tools - Safety requirements - Part 12: Circular, oscillating and reciprocating saws (ISO 11148-12:2012)
EN 16009:2011 Flameless explosion venting devices
EN 15268:2008 Petrol filling stations - Safety requirements for the construction of submersible pump assemblies
EN ISO 11148-2:2011 Hand-held non-electric power tools - Safety requirements - Part 2: Cutting-off and crimping power tools (ISO 11148-2:2011)
EN 1776:2015 Gas infrastructure - Gas measuring systems - Functional requirements
EN 1539:2015 Dryers and ovens, in which flammable substances are released - Safety requirements
EN 12581:2005+A1:2010 Coating plants - Machinery for dip coating and electrodeposition of organic liquid coating material - Safety requirements
EN 1953:2013 Atomising and spraying equipment for coating materials - Safety requirements
EN 14678-2:2007+A1:2012 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 2: Components other than dispensers and installation requirements
EN 16125:2015 LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase
EN ISO 11148-5:2011 Hand-held non-electric power tools - Safety requirements - Part 5: Rotary percussive drills (ISO 11148-5:2011)
EN 14492-1:2006+A1:2009/AC:2010 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 1: POWER DRIVEN WINCHES
EN 15089:2009 Explosion isolation systems
EN 14591-1:2004/AC:2006 EXPLOSION PREVENTION AND PROTECTION IN UNDERGROUND MINES - PROTECTIVE SYSTEMS - PART 1: 2-BAR EXPLOSION PROOF VENTILATION STRUCTURE
EN ISO 11148-1:2011 Hand-held non-electric power tools - Safety requirements - Part 1: Assembly power tools for non-threaded mechanical fasteners (ISO 11148-1:2011)
EN 14125:2013 Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
EN 14681:2006+A1:2010 Safety of machinery - Safety requirements for machinery and equipment for production of steel by electric arc furnaces
EN ISO 11148-3:2012 Hand-held non-electric power tools - Safety requirements - Part 3: Drills and tappers (ISO 11148-3:2012)
EN ISO 11148-11:2011 Hand-held non-electric power tools - Safety requirements - Part 11: Nibblers and shears (ISO 11148-11:2011)
EN 14973:2015 Conveyor belts for use in underground installations - Electrical and flammability safety requirements
EN 13852-1:2013 Cranes - Offshore cranes - Part 1: General-purpose offshore cranes
EN 14678-3:2013 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 3: Refuelling installations at commercial and industrial premises
EN 14492-2:2006+A1:2009/AC:2010 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
EN 14677:2008 Safety of machinery - Secondary steelmaking - Machinery and equipment for treatment of liquid steel
EN ISO 15136-2:2006 Petroleum and natural gas industries - Progressing cavity pump systems for artificial lift - Part 2: Surface-drive systems (ISO 15136-2:2006)
EN ISO 11148-10:2011 Hand-held non-electric power tools - Safety requirements - Part 10: Compression power tools (ISO 11148-10:2011)
EN 13852-2:2004 Cranes - Offshore cranes - Part 2: Floating cranes
BS EN ISO 8230-3:2008 Safety requirements for dry-cleaning machines Machines using combustible solvents
PREN 13617-4 : DRAFT 2010 PETROL FILLING STATIONS - PART 4: SAFETY REQUIREMENTS FOR CONSTRUCTION AND PERFORMANCE OF SWIVELS FOR USE ON METERING PUMPS AND DISPENSERS
09/30183560 DC : 0 BS ISO 11148-12 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 12: CIRCULAR, OSCILLATING AND RECIPROCATING SAWS
UNI EN ISO 11148-7 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS
UNE-EN 50177:2010 Stationary electrostatic application equipment for ignitable coating powders - Safety requirements
BS EN ISO 11148-3:2012 Hand-held non-electric power tools. Safety requirements Drills and tappers
DIN EN ISO 11148-4:2013-05 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 4: NON-ROTARY PERCUSSIVE POWER TOOLS (ISO 11148-4:2012)
I.S. EN ISO 11148-4:2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 4: NON-ROTARY PERCUSSIVE POWER TOOLS (ISO 11148-4:2012)
PREN 13160-3 : DRAFT 2014 LEAK DETECTION SYSTEMS - PART 3: REQUIREMENTS AND TEST/ASSESSMENT METHODS FOR LIQUID SYSTEMS FOR TANKS
09/30187377 DC : 0 BS ISO 11148-5 - HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 5: ROTARY PERCUSSIVE DRILLS
13/30277457 DC : 0 BS EN 1776 - GAS INFRASTRUCTURE - GAS MEASURING SYSTEMS - FUNCTIONAL REQUIREMENTS
BS EN 50050-1:2013 Electrostatic hand-held spraying equipment. Safety requirements Hand-held spraying equipment for ignitable liquid coating materials
DIN EN ISO 11148-7:2013-01 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS (ISO 11148-7:2012)
CEI EN 50050-3 : 2014 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
03/306594 DC : DRAFT APR 2003 BS EN 14681 - SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACE
03/306595 DC : 0 BS EN 14677 - SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL
I.S. EN 50050-1:2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 1: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE LIQUID COATING MATERIALS
14/30292850 DC : 0 BS EN 12779 - SAFETY OF WOODWORKING MACHINES - CHIPS AND DUST EXTRACTION SYSTEMS WITH FIXED INSTALLATIONS - SAFETY REQUIREMENTS
BS EN 16009:2011 Flameless explosion venting devices
UNE-EN 14678-3:2013 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 3: Refuelling installations at commercial and industrial premises
04/30113213 DC : 0 EN 14591-3 - EXPLOSION PROTECTION IN UNDERGROUND MINING - PROTECTIVE SYSTEMS - PART 3: WATER TROUGHS FOR EXPLOSION BARRIERS
13/30265319 DC : 0 BS EN 14973 - CONVEYOR BELTS FOR USE IN UNDERGROUND INSTALLATIONS - ELECTRICAL AND FLAMMABILITY SAFETY REQUIREMENTS
PREN 13463-5 : DRAFT 2009 NON-ELECTRICAL EQUIPMENT INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 5: PROTECTION BY CONSTRUCTIONAL SAFETY 'C'
05/30135286 DC : 0 EN 15268 - PETROL FILLING STATIONS - SAFETY REQUIREMENTS FOR THE CONSTRUCTION AND PERFORMANCE OF SUBMERSIBLE PUMP ASSEMBLIES
BS EN ISO 11148-4:2012 Hand-held non-electric power tools. Safety requirements Non-rotary percussive power tools
PD CLC/TR 50404:2003 Electrostatics. Code of practice for the avoidance of hazards due to static electricity
BS EN 14591-4:2007 Explosion prevention and protection in underground mines. Protective systems Automatic extinguishing systems for road headers
DIN EN 16009:2011-10 Flameless explosion venting devices
DIN EN 14677 E : 2008 SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL
PREN 13463-6 : DRAFT 2002 NON-ELECTRICAL EQUIPMENT FOR POTENTIALLY EXPLOSIVE ATMOSPHERES - PART 6: PROTECTION BY CONTROL OF IGNITION SOURCE 'B'
I.S. EN ISO 11148-2:2011 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 2: CUTTING-OFF AND CRIMPING POWER TOOLS (ISO 11148-2:2011)
I.S. EN 50050-3:2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 3: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE FLOCK
I.S. EN ISO 11148-7:2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 7: GRINDERS (ISO 11148-7:2012)
I.S. EN ISO 11148-11:2011 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 11: NIBBLERS AND SHEARS (ISO 11148-11:2011)
I.S. EN ISO 8230-3:2008 SAFETY REQUIREMENTS FOR DRY-CLEANING MACHINES - PART 3: MACHINES USING COMBUSTIBLE SOLVENTS
I.S. EN 14677:2008 SAFETY OF MACHINERY - SECONDARY STEELMAKING - MACHINERY AND EQUIPMENT FOR TREATMENT OF LIQUID STEEL
PREN 1127-2 : DRAFT 2012 EXPLOSIVE ATMOSPHERES - EXPLOSION PREVENTION AND PROTECTION - PART 2: BASIC CONCEPTS AND METHODOLOGY FOR MINING
I.S. EN 1034-17:2012 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR THE DESIGN AND CONSTRUCTION OF PAPER MAKING AND FINISHING MACHINES - PART 17: TISSUE MAKING MACHINES
UNI EN ISO 11148-10 : 2012 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 10: COMPRESSION POWER TOOLS
UNI CEI EN ISO/IEC 80079-34 : 2012 EXPLOSIVE ATMOSPHERES - PART 34: APPLICATION OF QUALITY SYSTEMS FOR EQUIPMENT MANUFACTURE
BS EN 1127-1:2011 Explosive atmospheres. Explosion prevention and protection Basic concepts and methodology
I.S. EN ISO 11148-5:2011 HAND-HELD NON-ELECTRIC POWER TOOLS - SAFETY REQUIREMENTS - PART 5: ROTARY PERCUSSIVE DRILLS (ISO 11148-5:2011)
CLC/TR 60079-32-1:2015 Explosive atmospheres - Part 32-1: Electrostatic Hazards - Guidance
I.S. EN 50223:2015 STATIONARY ELECTROSTATIC APPLICATION EQUIPMENT FOR IGNITABLE FLOCK MATERIAL - SAFETY REQUIREMENTS
DIN EN 14678-1:2013-06 LPG equipment and accessories - Construction and performance of LPG equipment for automotive filling stations - Part 1: Dispensers
DIN EN 14591-2:2007-07 Explosion prevention and protection in underground mines - Protective systems - Part 2: Passive water trough barriers
DIN EN 13237:2013-01 POTENTIALLY EXPLOSIVE ATMOSPHERES - TERMS AND DEFINITIONS FOR EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
DIN EN 14591-1:2004-12 Explosion prevention and protection in underground mines - Protective systems - Part 1: 2-bar-explosion proof ventilation structure
DIN EN 14492-2:2016-08 (Draft) CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
DIN EN 12921-3:2010-02 Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 3: Safety of machines using flammable cleaning liquids (includes Amendment A1:2008)
DIN EN 14125:2013-09 THERMOPLASTIC AND FLEXIBLE METAL PIPEWORK FOR UNDERGROUND INSTALLATION AT PETROL FILLING STATIONS
DIN EN 14492-1:2015-05 (Draft) Cranes - Power driven winches & hoists - part 1 power driven winches; German and English version prEN 14492-1:2015
BS EN 13852-2:2004 Cranes. Offshore cranes Floating cranes
UNE-EN 12779:2016 Safety of woodworking machines - Chip and dust extraction systems with fixed installation - Safety requirements
BS EN 14591-1:2004 Explosion prevention and protection in underground mines. Protective systems 2-bar explosion proof ventilation structure
BS EN 12581 : 2005 COATING PLANTS - MACHINERY FOR DIP COATING AND ELECTRODEPOSITION OF ORGANIC LIQUID COATING MATERIAL - SAFETY REQUIREMENTS
BS EN 15198:2007 Methodology for the risk assessment of non-electrical equipment and components for intended use in potentially explosive atmospheres
BS EN 14678-1:2013 LPG equipment and accessories. Construction and performance of LPG equipment for automotive filling stations Dispensers
BS EN 1953:2013 Atomising and spraying equipment for coating materials. Safety requirements
BS EN 13463-2:2004 Non-electrical equipment for use in potentially explosive atmospheres Protection by flow restricting enclosure \'fr\'
BS EN 13617-2:2012 Petrol filling stations Safety requirements for construction and performance of safe breaks for use on metering pumps and dispensers
ISO 11148-3:2012 Hand-held non-electric power tools — Safety requirements — Part 3: Drills and tappers
BS EN 1012-1:2010 Compressors and vacuum pumps. Safety requirements Air compressors
BS EN 13852-1:2013 Cranes. Offshore cranes General-purpose offshore cranes
BS EN 13160-3:2003 Leak detection systems Liquid systems for tanks
BS EN 14681 : 2006 SAFETY OF MACHINERY - SAFETY REQUIREMENTS FOR MACHINERY AND EQUIPMENT FOR PRODUCTION OF STEEL BY ELECTRIC ARC FURNACES
BS EN 14492-2 : 2006 CRANES - POWER DRIVEN WINCHES AND HOISTS - PART 2: POWER DRIVEN HOISTS
ISO 11148-12:2012 Hand-held non-electric power tools — Safety requirements — Part 12: Circular, oscillating and reciprocating saws
ISO 13709:2009 Centrifugal pumps for petroleum, petrochemical and natural gas industries
DIN EN 12693:2008-09 REFRIGERATING SYSTEMS AND HEAT PUMPS - SAFETY AND ENVIRONMENTAL REQUIREMENTS - POSITIVE DISPLACEMENT REFRIGERANT COMPRESSORS
EN 1012-3:2013 Compressors and vacuum pumps - Safety requirements - Part 3: Process compressors
EN 1127-2:2014 Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining
EN 12921-3:2005+A1:2008 Machines for surface cleaning and pre-treatment of industrial items using liquids or vapours - Part 3: Safety of machines using flammable cleaning liquids
EN 12981:2005+A1:2009 Coating plants - Spray booths for application of organic powder coating material - Safety requirements
EN 13760:2003 Automotive LPG filling system for light and heavy duty vehicles - Nozzle, test requirements and dimensions
EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
EN 1012-1:2010 Compressors and vacuum pumps - Safety requirements - Part 1: Air compressors
EN 14591-4:2007/AC:2008 EXPLOSION PREVENTION AND PROTECTION IN UNDERGROUND MINES - PROTECTIVE SYSTEMS - PART 4: AUTOMATIC EXTINGUISHING SYSTEMS FOR ROAD HEADERS
EN 13463-5:2011 Non-electrical equipment intended for use in potentially explosive atmospheres - Part 5: Protection by constructional safety 'c'
EN 50050-2 : 2013 ELECTROSTATIC HAND-HELD SPRAYING EQUIPMENT - SAFETY REQUIREMENTS - PART 2: HAND-HELD SPRAYING EQUIPMENT FOR IGNITABLE COATING POWDER
EN 50050-1:2013 Electrostatic hand-held spraying equipment - Safety requirements - Part 1: Hand-held spraying equipment for ignitable liquid coating materials
UNE-EN 12757-1:2006+A1:2010 Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing
UNE-EN 16125:2020 LPG Equipment and Accessories - Pipework systems and supports - LPG in liquid phase and vapour pressure phase
API RP 697:2023 Pump Repair
UNE-EN 12757-1:2006 Mixing machinery for coating materials - Safety requirements - Part 1: Mixing machinery for use in vehicle refinishing
UNE-EN 1804-3:2007 Machines for underground mines - Safety requirements for hydraulic powered roof supports - Part 3: Hydraulic control systems

EN 62262:2002 Degrees of protection provided by enclosures for electrical equipment against external mechanical impacts (IK code)
ISO 6507-1:2005 Metallic materials Vickers hardness test Part 1: Test method
EN 1127-1:2011 Explosive atmospheres - Explosion prevention and protection - Part 1: Basic concepts and methodology
IEC 60079-1:2014 RLV Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
EN 60079-26:2015 Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
ISO 6507-4:2005 Metallic materials Vickers hardness test Part 4: Tables of hardness values
EN 582:1993 Thermal spraying - Determination of tensile adhesive strength
EN 60079-1:2014 Explosive atmospheres - Part 1: Equipment protection by flameproof enclosures "d"
IEC TR 60079-20:1996 Electrical apparatus for explosive gas atmospheres - Part 20: Data for flammable gases and vapours, relating to the use of electrical apparatus
EN 60079-0:2012/A11:2013 EXPLOSIVE ATMOSPHERES - PART 0: EQUIPMENT - GENERAL REQUIREMENTS (IEC 60079-0:2011, MODIFIED)
EN 12874 : 2001 FLAME ARRESTERS - PERFORMANCE REQUIREMENTS, TEST METHODS AND LIMITS FOR USE
EN 13237:2012 Potentially explosive atmospheres - Terms and definitions for equipment and protective systems intended for use in potentially explosive atmospheres
EN 13463-6:2005 Non-electrical equipment for use in potentially explosive atmospheres - Part 6: Protection by control of ignition source 'b'
EN 60079-28:2015 Explosive atmospheres - Part 28: Protection of equipment and transmission systems using optical radiation
ISO 281:2007 Rolling bearings Dynamic load ratings and rating life
EN 14986:2017 Design of fans working in potentially explosive atmospheres
EN 1755:2015 Industrial Trucks - Safety requirements and verification - Supplementary requirements for operation in potentially explosive atmospheres
EN 13463-8:2003 Non-electrical equipment for potentially explosive atmospheres - Part 8: Protection by liquid immersion 'k'
EN 61241-1:2004/corrigendum Dec. 2006 ELECTRICAL APPARATUS FOR USE IN THE PRESENCE OF COMBUSTIBLE DUST - PART 1: PROTECTION BY ENCLOSURES "TD"
EN 1127-2:2014 Explosive atmospheres - Explosion prevention and protection - Part 2: Basic concepts and methodology for mining
EN ISO 12100-1:2003/A1:2009 SAFETY OF MACHINERY - BASIC CONCEPTS, GENERAL PRINCIPLES FOR DESIGN - PART 1: BASIC TERMINOLOGY, METHODOLOGY
EN 15198:2007 Methodology for the risk assessment of non-electrical equipment and components for intended use in potentially explosive atmospheres
IEC 61241-1:2004 Electrical apparatus for use in the presence of combustible dust - Part 1: Protection by enclosures "tD"
EN 13463-2:2004 Non-electrical equipment for use in potentially explosive atmospheres - Part 2: Protection by flow restricting enclosure 'fr'
IEC 60079-0:2011 Explosive atmospheres - Part 0: Equipment - General requirements
ISO 12100-1:2003 Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
EN 14522:2005 Determination of the auto ignition temperature of gases and vapours
EN 13463-5:2011 Non-electrical equipment intended for use in potentially explosive atmospheres - Part 5: Protection by constructional safety 'c'
EN 13463-3:2005 Non-electrical equipment for use in potentially explosive atmospheres - Part 3: Protection by flameproof enclosure 'd'
IEC TR 60079-12:1978 Electrical apparatus for explosive gas atmospheres - Part 12:Classification of mixtures of gases of vapours with air accordingto their maximum experimental safe gaps and minimum ignitingcurrents
EN 50303:2000 Group I, Category M1 equipment intended to remain functional in atmospheres endangered by firedamp and/or coal dust
IEC 60079-26:2014 RLV Explosive atmospheres - Part 26: Equipment with Equipment Protection Level (EPL) Ga
CLC/TR 50404:2003 Electrostatics - Code of practice for the avoidance of hazards due to static electricity
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
1994/9/EC : 1994 DIRECTIVE 94/9/EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL OF 23 MARCH 1994 ON THE APPROXIMATION OF THE LAWS OF THE MEMBER STATES CONCERNING EQUIPMENT AND PROTECTIVE SYSTEMS INTENDED FOR USE IN POTENTIALLY EXPLOSIVE ATMOSPHERES
EN 60079-2:2014/AC:2015 EXPLOSIVE ATMOSPHERES - PART 2: EQUIPMENT PROTECTION BY PRESSURIZED ENCLOSURE 'P' (IEC 60079-2:2014)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.