• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

EN 1451-1:2017

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system

Superseded date

03-02-2020

Published date

15-11-2017

European foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Material
6 General characteristics
7 Geometrical characteristics
8 Mechanical characteristics
9 Physical characteristics
10 Performance requirements
11 Sealing rings
12 Marking
Annex A (normative) - Utilization of non-virgin PP material
Annex B (informative) - Product standards
Bibliography

This part of EN 1451 specifies the requirements for solid-wall polypropylene (PP) pipes, fittings and the system intended for:-soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");-soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code "BD").This part of EN 1451 is also applicable to PP pipes and fittings and the system intended for the following purposes:-ventilating part of the pipework in association with discharge applications;-rainwater pipework within the building structure.It also specifies the test parameters for the test methods referred to in this standard.This standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.It applies to pipes and fittings, marked with "B", which are intended to be used inside buildings and outside buildings fixed onto the wall.This standard is applicable to PP pipes and fittings of the following types:-plain-ended;-with integral elastomeric ring seal socket;-for butt fusion joints.whereby the fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.

Committee
CEN/TC 155
DevelopmentNote
Supersedes PREN 1451-1. (11/2017)
DocumentType
Standard
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

ISO 580:2005 Plastics piping and ducting systems — Injection-moulded thermoplastics fittings — Methods for visually assessing the effects of heating
EN ISO 3126:2005 Plastics piping systems - Plastics components - Determination of dimensions (ISO 3126:2005)
ISO/TR 10358:1993 Plastics pipes and fittings Combined chemical-resistance classification table
ISO 13259:2010 Thermoplastics piping systems for underground non-pressure applications Test method for leaktightness of elastomeric sealing ring type joints
ISO 3451-1:2008 Plastics Determination of ash Part 1: General methods
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
ISO 13263:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for impact strength
EN ISO 1043-1:2011/A1:2016 PLASTICS - SYMBOLS AND ABBREVIATED TERMS - PART 1: BASIC POLYMER AND THEIR SPECIAL CHARACTERISTICS (ISO 1043-1:2011/AMD 1:2016)
ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 265-1:1988 Pipes and fittings of plastics materials Fittings for domestic and industrial waste pipes Basic dimensions: Metric series Part 1: Unplasticized poly(vinyl chloride) (PVC-U)
ISO 1133-1:2011 Plastics Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics Part 1: Standard method
ISO 13255:2010 Thermoplastics piping systems for soil and waste discharge inside buildings Test method for airtightness of joints
EN ISO 11173:2017 Thermoplastics pipes - Determination of resistance to external blows - Staircase method (ISO 11173:1994)
EN ISO 3451-1:2008 Plastics - Determination of ash - Part 1: General methods (ISO 3451-1:2008)
EN ISO 1167-2:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 2: Preparation of pipe test pieces (ISO 1167-2:2006)
ISO/TR 7620:2005 Rubber materials — Chemical resistance
EN ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - Determination of the resistance to internal pressure - Part 1: General method (ISO 1167-1:2006)
EN 681-2:2000/A2:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 2: THERMOPLASTIC ELASTOMERS
ISO 3126:2005 Plastics piping systems Plastics components Determination of dimensions
EN 476:2011 General requirements for components used in drains and sewers
EN ISO 1133-1:2011 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 1: Standard method (ISO 1133-1:2011)
ISO 472:2013 Plastics Vocabulary
EN ISO 3127:2017 Thermoplastics pipes - Determination of resistance to external blows - Round-the-clock method (ISO 3127:1994)
CEN/TR 13801:2014 Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation
EN ISO 13967:2009 Thermoplastics fittings - Determination of ring stiffness (ISO 13967:2009)
ISO 1183-2:2004 Plastics Methods for determining the density of non-cellular plastics Part 2: Density gradient column method
EN ISO 9969:2016 Thermoplastics pipes - Determination of ring stiffness (ISO 9969:2016)
EN ISO 580:2005 Plastics piping and ducting systems - Injection-moulded thermoplastics fittings - Methods for visually assessing the effects of heating (ISO 580:2005)
EN ISO 13254:2017 Thermoplastics piping systems for non-pressure applications - Test method for watertightness (ISO 13254:2010)
ISO 11357-6:2008 Plastics Differential scanning calorimetry (DSC) Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
ISO 4065:1996 Thermoplastics pipes Universal wall thickness table
EN ISO 2505:2005 Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505:2005)
ISO 13967:2009 Thermoplastics fittings Determination of ring stiffness
ISO 13257:2010 Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycling
EN ISO 13257:2017 Thermoplastics piping systems for non-pressure applications - Test method for resistance to elevated temperature cycling (ISO 13257:2010)
ISO 13254:2010 Thermoplastics piping systems for non-pressure applications Test method for watertightness
ISO 13264:2010 Thermoplastics piping systems for non-pressure underground drainage and sewerage Thermoplastics fittings Test method for mechanical strength or flexibility of fabricated fittings
ISO 1043-1:2011 Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
ISO 9969:2016 Thermoplastics pipes Determination of ring stiffness
EN ISO 472:2013 Plastics - Vocabulary (ISO 472:2013)
EN 12099:1997 Plastics piping systems - Polyethylene piping materials and components - Determination of volatile content
EN ISO 1183-2:2004 PLASTICS - METHODS FOR DETERMINING THE DENSITY OF NON-CELLULAR PLASTICS - PART 2: DENSITY GRADIENT COLUMN METHOD
ISO 1167-1:2006 Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method
ISO 2505:2005 Thermoplastics pipes — Longitudinal reversion — Test method and parameters

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.