EN 14605:2005+A1:2009
Current
Protective clothing against liquid chemicals - performance requirements for clothing with liquid-tight (Type 3) or spray-tight (Type 4) connections, including items providing protection to parts of the body only (Types PB [3] and PB [4])
06-05-2009
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
4.1 Materials
4.2 Seams, joins and assemblages
4.3 Performance requirements for whole suits (Types 3 and 4)
4.3.1 General
4.3.2 Pre-conditioning
4.3.3 Conditioning
4.3.4 Resistance to penetration by liquids
4.4 Visor
4.4.1 General
4.4.2 Mechanical strength of visor
4.4.3 Field of vision
4.4.4 Distortion of vision
5 Marking
6 Information supplied by the manufacturer
Annex ZA (informative) Relationship between this European
Standard and the Essential Requirements
of EU Directive 89/686/EEC
Bibliography
This document specifies the minimum requirements for the following types of limited use and reusable chemical protective clothing:-Full-body protective clothing with liquid-tight connections between different parts of the clothing (Type 3: liquid-tight clothing) and, if applicable, with liquid-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards. Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves;-Full-body protective clothing with spray-tight connections between different parts of the clothing (Type 4: spray-tight clothing) and, if applicable, spray-tight connections to component parts, such as hoods, gloves, boots, visors or respiratory protective equipment, which may be specified in other European Standards. Examples of such clothing are one-piece coveralls or two-piece suits, with or without hood or visors, with or without boot-socks or over-boots, with or without gloves;-Partial body protection garments offering protection to specific parts of the body against permeation of chemical liquids.Examples of such garments are e.g. laboratory coats, jackets, trousers, aprons, sleeves, hoods (not air-supplied) etc. As partial body protection leaves some parts of the body unprotected this document specifies only the performance requirements for the clothing material and the seams.NOTEPartial body chemical protective garments which offer only protection against penetration of chemical liquids are within the scope of EN 13034 (Type PB [6] clothing).
| Committee |
CEN/TC 162
|
| DevelopmentNote |
Supersedes EN 465, EN 466 and EN 467. (04/2005) 2005 Edition Re-Issued in May 2009 & incorporates AMD 1 2009. (06/2009)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| NS EN 14605 : 2005 + A1 2009 | Identical |
| NF EN 14605 : 2005 + A1 2009 | Identical |
| PN EN 14605 : 2008 + A1 2010 | Identical |
| NBN EN 14605 : 2006 + A1 2009 | Identical |
| NEN EN 14605 : 2005 + A1 2009 | Identical |
| I.S. EN 14605:2005+A1:2009 | Identical |
| BS EN 14605:2005+A1:2009 | Identical |
| BS EN 14605 : 2005 | Identical |
| DIN EN 14605:2009-08 | Identical |
| UNE-EN 14605:2005+A1:2009 | Identical |
| UNE-EN 14605:2005 | Identical |