EN 3915:2008
Current
Current
The latest, up-to-date edition.
Aerospace series - Insert, thin wall, self-locking, MJ threads, in heat resisting nickel base alloy NI-PH2601 (NI-P100HT, Inconel 718), for salvage of components - Classification: 1 275 MPa (at ambient temperature) / 550 °C - Technical specification
Published date
16-04-2008
Publisher
Sorry this product is not available in your region.
Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Quality assurance
4.1 Qualification
4.1.1 Purpose
4.1.2 EN 9133
4.2 Acceptance
4.2.1 Purpose
4.2.2 Conditions
4.2.3 Responsibility
4.2.4 Inspection and test report
5 Requirements
This standard specifies the characteristics, qualification and acceptance requirements for self-locking thin wall salvage inserts with MJ threads in NI-PH2601 (NI P100HT).Classification: 1 275 MPa ) / 550 °C ).
| Committee |
ASD-STAN
|
| DevelopmentNote |
Supersedes PREN 3915. (05/2008)
|
| DocumentType |
Standard
|
| PublisherName |
Comite Europeen de Normalisation
|
| Status |
Current
|
| Supersedes |
| Standards | Relationship |
| PN EN 3915 : 2008 | Identical |
| BS EN 3915:2008 | Identical |
| NBN EN 3915 : 2008 | Identical |
| I.S. EN 3915:2008 | Identical |
| NS EN 3915 : 1ED 2008 | Identical |
| NF EN 3915 : 2008 | Identical |
| DIN EN 3915:2008-12 | Identical |
| NEN EN 3915 : 2008 | Identical |
| UNE-EN 3915:2008 | Identical |
| NF EN 3916 : 2009 | AEROSPACE SERIES - INSERT, THIN WALL - SALVAGE PROCEDURE FOR COMPONENTS |
| I.S. EN 3916:2008 | AEROSPACE SERIES - INSERT, THIN WALL - SALVAGE PROCEDURE FOR COMPONENTS |
| I.S. EN 3914:2008 | AEROSPACE SERIES - INSERT, THIN WALL, SELF-LOCKING, LONG, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH2601 (NI-P100HT, INCONEL 718), SILVER PLATED ON INTERNAL THREAD, FOR SALVAGE OF COMPONENTS |
| EN 3916:2008 | Aerospace series - Insert, thin wall - Salvage procedure for components |
| NF EN 3914 : 2008 | AEROSPACE SERIES - INSERT, THIN WALL, SELF-LOCKING, LONG, IN HEAT RESISTING NICKEL BASE ALLOY NI-PH2601 (NI-P100HT, INCONEL 718), SILVER PLATED ON INTERNAL THREAD, FOR SALVAGE OF COMPONENTS |
| BS EN 3914:2008 | Aerospace series. Insert, thin wall, self-locking, long, in heat resisting nickel base alloy NI-PH2601 (NI-P100HT, Inconel 718), silver plated on internal thread, for salvage of components |
| EN 3914:2008 | Aerospace series - Insert, thin wall, self-locking, long, in heat resisting nickel base alloy NI-PH2601 (NI-P100HT, Inconel 718), silver plated on internal thread, for salvage of components |
| BS EN 3916:2008 | Aerospace series. Insert, thin wall. Salvage procedure for components |
| ISO 3534:1977 | Statistics — Vocabulary and symbols |
| ISO 5855-2:1999 | Aerospace — MJ threads — Part 2: Limit dimensions for bolts and nuts |
| EN ISO 4288:1997 | Geometrical product specifications (GPS) - Surface texture: Profile method - Rules and procedures for the assessment of surface texture (ISO 4288:1996) |
| PREN 4376 : 200P1 | AEROSPACE SERIES - HEAT RESISTING ALLOY NI-PH2601 (NICR19FE19NB5MO3) - SOLUTION TREATED AND PRECIPITATION TREATED - BAR AND SECTION - D[E] <= 200 MM |
| ISO 3452:1984 | Non-destructive testing — Penetrant inspection — General principles |
| EN 3298:2008 | Aerospace series - Inserts, thin wall, self-locking - Installation and removal procedure |
| EN 3676:1998 | Aerospace series - Inserts, thin wall, self-locking - Design standard |
| PREN 4377 : 200P1 | AEROSPACE SERIES - HEAT RESISTING ALLOY NI-PH2601 (NICR19FE19NB5MO3) - NON HEAT TREATED - FORGING STOCK - A OR D <= 300 MM |
| PREN 2404 : 2 | AEROSPACE SERIES - HEAT RESISTING NICKEL BASE ALLOY NI-P100-HT - SOLUTION TREATED AND PRECIPITATION TREATED - BARS |
| SAE AMS4117K | Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061; -T6, -T651) |
| ISO 8642:2008 | Aerospace — Self-locking nuts with maximum operating temperature greater than 425 degrees C — Test methods |
Summarise
Sorry this product is not available in your region.